AEG Su 86000 5i Operating And Installation Instructions

Installation
11

4.
The joint cover (B) is to be
assembled after having installed
the appliance in the recess.

B
4
1

Push the appliance
into place. The plug
socket necessary for
connection of the
appliance to the elec-
tricity supply should 
be positioned, so that
the plug is not placed
in the recess.

3.
To adjust the height
proceed as follows:
Loosen or tighten the
two front feet.
The rear feet are
adjusted by turning the screw in the front kick plate to the left or
right.

596
555
max
+
-
3
+
-...

Installation
12

7

6.
To mount the furniture door
proceed as shown in the fig-
ures:

5.
Push the appliance
into place and retain
the cabinet with
screws (I) through the
securing brackets into
the worktop or adja-
cent woodwork as
necessary.

ab
c
C
click
click
8

5
I
a
b
10
1 2
3 4
C
6
 

Installation
13

I
27,5 cm27,5 cm
55 cm
10
F
b
=
=
9
I
c
MšbeltŸr Innenseitea
Upper part of kitchen 
furniture panel
12
3
45
°
11=
=
10
12
1
2
 

Installation
14

90°
115 °
L
L
15

14
A

8 mm
13
G
K
I
F

7.
Refit the covering strip.
 

15
Installation

Fitting the plinth

Important!

For the efficient operation of
the appliance, it is important
that the original ventilation
grid is used.¥ For an opening height dimension A=820 mm and a
plinth height dimension
a=100 mm, the plinth may
be fitted without adjust-
ments. The same applies to
an opening height dimen-
sion B=890 mm and a
plinth height dimension
b=170 mm.
¥ For plinth heights greater than  a=100 mm, b=170 mm, a cut should be made in the plinth, 580 mm
wide, in the centre of the...

16
Installation

Electrical Connection

Any electrical work required to install this appliance should be carried
out by a qualified electrician or competent person.

WARNING Ð THIS APPLIANCE MUST BE EARTHED
The manufacturer declines any liability should these safety mea-
sures not be observed.

Before switching on, make sure the electricity supply voltage is the
same as that indicated on the appliance rating plate. The rating plate
is inside, on the right.
The appliance is supplied with a 13 amp plug...

17

Description of the appliance
View of the appliance

1 Butter/cheese compartment
2 Sliding shelf
3 Bottle shelf
4 Vegetable drawers
5 Storage shelves
6Thermostat

Prior to Initial StartÐUp

Please clean the appliance interior and all accessories prior to initial\
start-up (see section: ÒCleaning and CareÓ).
+

À
Á
Â
Ã Ä Å
 

18

Starting up and temperature regulation

Important!
Only use the appliance when builtÐin!

+
1.
Connect the appliance to the mains electricity supply.
When the refrigerator compartment door is opened, the internal light-
ing is switched on.
The temperature control knob is
located on the right hand side of the
refrigerator compartment.

Setting Ò0Ó means:
Off.

2.
Turn the control knob clockwise past 
Ò1Ó. The refrigerating unit is now on 
and operates automatically.

Setting Ò1Ó means:

Hightest...

19

Switching off the appliance

To switch off the appliance, turn the temperature regulator to position
0.

If the appliance is not going to be used for an extended period:

+
1.
Remove all refrigerated packages.

2.
Switch off the appliance by turning the thermostat knob to position
0.

3.
Remove the mains plug or switch off or disconnect from the electricity
supply.

4.
Clean thoroughly (see section: ÒCleaning and CareÓ).

5.
Leave the door open to avoid the build up of odours.

+

Interior...

20
Interior Accessories

Variable Storage Box

Some models are equipped with a variable stor-
age box which is fitted under a door shelf com-
partment and can be slid sideways.
The variable box can be hung from a
storage shelf in the refrigerator com-
partment:

+
1.
Pull the storage shelf forward until it
can be tipped up or down and removed.

2.
Hang the retaining bracket on the taper
on the storage shelf and slide the stor-
age shelf back into the guides.

Bottle Holder

Some models are equipped with...