AEG Su 86000 4i Operating And Installation Instructions

Installation
11
If necessary, pads (E) are supplied for the
rear feet to make sliding the appliance in
and out of the recess easier. To fit the pads,
press them onto the rear feet.
If required, the dimensions of these pads
can be reduced by breaking them where
marked.
II52
E
4.The joint cover (B) is to be
assembled after having installed
the appliance in the recess.
B
4
1
Push the appliance
into place. The plug
socket necessary for
connection of the
appliance to the elec-
tricity supply should 
be...

Installation
12
7
6.To mount the furniture door
proceed as shown in the fig-
ures:
5.Push the appliance
into place and retain
the cabinet with
screws (I) through the
securing brackets into
the worktop or adja-
cent woodwork as
necessary.
ab
c
C
click
click
8
5
I
a
b
10
12
34C
6
 

Installation
13
I
27,5 cm27,5 cm
55 cm
10
F
b
==
9
I
c
MšbeltŸr Innenseitea
Upper part of kitchen 
furniture panel
12
3
45°
11= =
10
12
1
2
 

Installation
14
90°
115°L
L
15
14
A
8 mm
13
G
K
I
F
7.Refit the covering strip.
 

15
Installation
Fitting the plinth
Important!
For the efficient operation of the appliance, it is important that the
original ventilation grid is used.
¥ For an opening height dimension
A=820 mm and a plinth height
dimension a=100 mm, the plinth may
be fitted without adjustments. The
same applies to an opening height
dimension B=870 mm and a plinth
height dimension b=150 mm.
¥ For plinth heights greater than 
a=100 mm, b=150 mm, a cut should
be made in the plinth, 580 mm wide,
in the centre of the...

16
Installation
Electrical Connection
Any electrical work required to install this appliance should be carried
out by a qualified electrician or competent person.
WARNING Ð THIS APPLIANCE MUST BE EARTHED
The manufacturer declines any liability should these safety mea-
sures not be observed.
Before switching on, make sure the electricity supply voltage is the
same as that indicated on the appliance rating plate. The rating plate
is inside, on the right.
The appliance is supplied with a 13 amp plug fitted....

17
Description of the appliance
View of the appliance
1 Butter/cheese compartment
2 Sliding shelf
3 Bottle shelf
4 Vegetable drawers
5 Storage shelves
6
Thermostat
Prior to Initial StartÐUp
Please clean the appliance interior and all accessories prior to initial
start-up (see section: ÒCleaning and CareÓ).+
À
Á
Â
à ÄÅ
 

18
Starting up and temperature regulation
Important!Only use the appliance when builtÐin!
+1.Connect the appliance to the mains electricity supply.
When the refrigerator compartment door is opened, the internal light-
ing is switched on.
The temperature control knob is
located on the right hand side of the
refrigerator compartment.
Setting Ò0Ó means:Off.
2.Turn the control knobclockwise past 
Ò1Ó. The refrigerating unit is now on 
and operates automatically.
Setting Ò1Ó means:
Hightest temperature,...

19
Switching off the appliance
To switch off the appliance, turn the temperature regulator to position
0.
If the appliance is not going to be used for an extended period:
+1.Remove all refrigerated packages.
2.Switch off the appliance by turning the thermostat knob to position
0.
3.Remove the mains plug or switch off or disconnect from the electricity
supply.
4.Clean thoroughly (see section: ÒCleaning and CareÓ).
5.Leave the door open to avoid the build up of odours.
+
Interior Accessories
Storage...

20
Interior Accessories
Variable Storage Box
Some models are equipped with a variable stor-
age box which is fitted under a door shelf com-
partment and can be slid sideways.
The variable box can be hung from a
storage shelf in the refrigerator com-
partment:
+1.Pull the storage shelf forward until it
can be tipped up or down and removed.
2.Hang the retaining bracket on the taper
on the storage shelf and slide the stor-
age shelf back into the guides.
Bottle Holder
Some models are equipped with a bottle...