AEG Steam oven BS831470KM User Manual
Have a look at the manual AEG Steam oven BS831470KM User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 513 AEG manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
4.Press . Remove the baking tray after the end of the procedure.12.9 Tank Emptying Remove all accessories. The cleaning function removes the residual water from the water drawer. Use the function after the steam cooking function. Select the function from the menu: Cleaning. The user interface will guide you through the procedure. The duration of the function is around 6 minutes. The light in this function is off. 1. Put the baking tray on the first shelf position. 2. Press . Remove the baking tray after the end of the procedure. 12.10 Removing and installing the door You can remove the door and the internal glass panels to clean it. The number of glass panels is different for different models. WARNING! Be careful when you remove the door from the appliance. The door is heavy. 1. Open the door fully. 2. Fully press the clamping levers (A) on the two door hinges. 3. Close the oven door to the first opening position (approximately 70° angle). 4. Hold the door with one hand on each side and pull it away from the appliance at an upwards angle. 5. Put the door with the outer side down on a soft cloth on a stable surface. This is to prevent scratches. 6. Hold the door trim (B) on the top edge of the door at the two sides and push inwards to release the clip seal. 7. Pull the door trim to the front to remove it. 8. Hold the door glass panels on their top edge one by one and pull them up out of the guide. 9. Clean the glass panel with water and soap. Dry the glass panel carefully. When the cleaning is completed, install the glass panels and the door. Do the above steps in the opposite sequence. Install the smaller panel first, then the larger. 12.11 Replacing the lamp Put a cloth on the bottom of the interior of the appliance. It prevents damage to the lamp glass cover and the cavity. WARNING! Danger of electrocution! Disconnect the fuse before you replace the lamp. The lamp and the lamp glass cover can be hot. 1. Deactivate the appliance. 2. Remove the fuses from the fuse box or deactivate the circuit breaker. ENGLISH51 AA 1 2 B
The top lamp1. Turn the lamp glass cover counterclockwise to remove it. 2. Remove the metal ring and clean the glass cover. 3. Replace the lamp with a suitable 300 °C heat-resistant lamp. 4. Attach the metal ring to the glass cover. 5. Install the glass cover.The side lamp 1.Remove the left shelf support to get access to the lamp. 2. Use a Torx 20 screwdriver to remove the cover. 3. Remove and clean the metal frame and the seal. 4. Replace the lamp with a suitable 300 °C heat-resistant lamp. 5. Install the metal frame and the seal. Tighten the screws. 6. Install the left shelf support. 13. TROUBLESHOOTINGWARNING! Refer to Safety chapters.13.1 What to do if...ProblemPossible causeRemedyYou cannot activate or oper- ate the oven.The oven is not connected to an electrical supply or it is connected incorrectly.Check if the oven is correctly connected to the electrical supply (refer to the connec- tion diagram if available).The oven does not heat up.The oven is deactivated.Activate the oven.The oven does not heat up.The clock is not set.Set the clock.The oven does not heat up.The necessary settings are not set.Make sure that the settings are correct.The oven does not heat up.The automatic switch-off is activated. Refer to "Automatic switch- off". The oven does not heat up.The Child Lock is on.Refer to "Using the Child Lock".The oven does not heat up.The door is not closed cor- rectly.Fully close the door.The oven does not heat up.The fuse is blown.Make sure that the fuse is the cause of the malfunction. If the fuse is blown again and again, contact a quali- fied electrician.www.aeg.com52
ProblemPossible causeRemedyThe lamp does not operate.The lamp is defective.Replace the lamp.The display shows F111.The plug of the core tem- perature sensor is not cor- rectly installed into the sock- et.Put the plug of the core tem- perature sensor as far as possible into the socket.The display shows an error code that is not in this table. There is an electrical fault.• Deactivate the oven with the house fuse or the safety switch in the fuse box and activate it again. • If the display shows the error code again, contact the Customer Care De- partment.Steam and condensation settle on the food and in the cavity of the oven.You left the dish in the oven for too long.Do not leave the dishes in the oven for longer than 15 - 20 minutes after the cooking process ends.The descaling procedure is interrupted before it finishes.There was a power cut.Repeat the procedure.The descaling procedure is interrupted before it finishes.The function was stopped by the user.Repeat the procedure.There is no water inside the grill- / roasting pan after the descaling procedure.You did not fill the water drawer to the maximum lev- el.Check if the a descaling agent / water is present in the water drawer body. Repeat the procedure.There is dirty water on the bottom of the cavity after the descaling cycle.The grill- / roasting pan is on a wrong shelf position.Remove the residual water and the descaling agent from the bottom of the oven. Put the grill- / roasting pan on the first shelf posi- tion.The cleaning function is in- terrupted before it finishes.There was a power cut.Repeat the procedure.The cleaning function is in- terrupted before it finishes.The function was stopped by the user.Repeat the procedure.There is too much water on the bottom of the cavity af- ter the end of the cleaning function.You sprayed too much de- tergent in the appliance be- fore the activation of the cleaning cycle.Cover all parts of the cavity with a thin layer of the deter- gent. Spray the detergent evenly.There is no good perform- ance of the cleaning proce- dure.The initial oven cavity tem- perature of the steam clean- ing function was too high.Repeat the cycle. Run the cy- cle when the appliance is cold.ENGLISH53
ProblemPossible causeRemedyThere is no good perform- ance of the cleaning proce- dure.You did not remove the side grids before the start of the cleaning procedure. They can transfer heat to the walls and decrease the perform- ance.Remove the side grids from the appliance and repeat the function.There is no good perform- ance of the cleaning proce- dure.You did not remove the ac- cessories from the appliance before the start of the clean- ing procedure. They can compromise the steam cycle and decrease the perform- ance.Remove the accessories from the appliance and re- peat the function.13.2 Service data If you cannot find a solution to the problem yourself, contact your dealer or an Authorised Service Centre. The necessary data for the service centre is on the rating plate. The rating plate ison the front frame of the appliance cavity. Do not remove the rating plate from the appliance cavity.We recommend that you write the data here:Model (MOD.).........................................Product number (PNC).........................................Serial number (S.N.).........................................14. ENERGY EFFICIENCY14.1 Product Fiche and information according to EU 65-66/2014Supplier's nameAEGModel identificationBS831470KMEnergy Efficiency Index81.2Energy efficiency classA+Energy consumption with a standard load, conven- tional mode0.89 kWh/cycleEnergy consumption with a standard load, fan-forced mode0.69 kWh/cycleNumber of cavities1www.aeg.com54
Heat sourceElectricityVolume71 lType of ovenBuilt-In OvenMass44.5 kgEN 60350-1 - Household electric cooking appliances - Part 1: Ranges, ovens, steam ovens and grills - Methods for measuring performance.14.2 Energy saving The appliance contains features which help you save energy during everydaycooking. General hints Make sure that the oven door is closedproperly when the appliance operates and keep it closed as much as possible during the cooking. Use metal dishes to improve the energy saving. When possible, do not preheat the oven before you put the food inside. When the cooking duration is longer than 30 minutes, reduce the oven temperature 3 - 10 minutes before the end of the cooking time, depending on the duration of the cooking. The residual heat inside the oven will continue to cook. Use the residual heat to warm up other foods. Cooking with fan When possible, use the cooking functions with fan to save energy.Residual heat In some heating functions if a programme with time selection Duration or End Time is activated and the cooking time is longer than 30 minutes, the heating elements deactivate automatically 10% earlier. The fan and lamp continue to operate. Cooking with the lamp off Deactivate the lamp during the cookingand activate only when you need it. Keep food warm If you want to use the residual heat to keep the meal warm, choose the lowest possible temperature setting. The display shows the residual heat temperature. Moist Fan Baking When you use the function Moist Fan Baking, the lamp deactivates after 30 seconds. You may activate the lamp again but this action will reduce the expected energy savings. 15. ENVIRONMENT CONCERNSPlease recycle all materials marked with the symbol . Dispose of all packaging materials appropriately and help to protect the environment, and future generations. Do not dispose of electrical equipment marked with the symbol along with the general house hold waste. Dispose all electrical goods via applicable local authority collections, or at local authority or, commercial recycling centres. * ENGLISH55