AEG Sc 81842 5i Operating And Installation Instructions

31
Remove transport safeguard
The appliance and the interior fittings are protected for transport.
 Pull off the adhesive tape on the left and right side of the door.
 Remove all adhesive tape and packing pieces from the interior of the
appliance.
Disposal
Appliance Packaging Information
All materials are environmentally sound! They can be dumped or burned at
an incinerating plant without danger!
About the materials: The plastics can be recycled and are identified as fol-
lows:
>PE< for polyethylene,...

32
Installation
Installation Location
The appliance should be set up in a well ventilated, dry room.
Energy use is affected by the ambient temperature. The appliance should
therefore
– not be exposed to direct sunlight;
– not be installed next to radiators, cookers or other sources of heat;
– only be installed at a location whose ambient temperature corresponds to
the climate classification, for which the appliance is designed.
The climate classification can be found on the serial plate, which is...

33

 
Your appliance needs air
For safety reasons, minimum
ventilationmust be as shown Fig.
Attention: keep ventilation ope-
nings clear of obstruction;



	
	



Rehingeing the door
The side at which the door opens can be changed from the right side (fac-
tory adjustment) to the left side, if the installation site requires.
Warning!When changing the side at
which the door opens, the appliance
may not be connected to the mains.
Remove plug from the mains befo-
rehand.
1....

34
Instructions for total built-in


Apply joint the sealing strip as shown
in figure. 7. Refit the upper door , the hinge pin
and the spacer on the opposite side 
1
244mm
Make sure that a distance of 44 mm
is maintained in the lower part bet-
ween the kitchen furniture and the
border of the appliance.
The lower hinge cover inserted in the
accessories bag, is useful to guarantee
the exact position of the kitchen fur-
niture and the appliance.
Also make sure that the appliance
does not clamp the mains...

35
Apply covers (C-D) on joint cover
lugs and into hinge holes.
Snap vent grille (B) and hinge
covers(E) into position.
BE
E
DC
I
I
Fasten the appliance with 4 screws
provided in the kit included with the
appliance.
From the plastic cover (E), which is
used to cover the hinge with the
pivot pin, you must take away the
part as indicated in the drawing.
This operation is made easer since
there is, in the internal part of the
cover hinge lid a groove that facila-
tes the removal of this coomponent.
“Remove...

36
Place guide (Ha) on the inside part of
the furniture door, up and down as
shown in the figure and mark the
position of external holes. After having
drilled holes, fix the guide with the
screws supplied.




















Separate parts Ha, Hb, Hc, Hd as
shown in the figure
 

37
Fix cover (Hc) on guide (Ha) until it
clips into place.













Open the appliance door and the fur-
niture door at 90°. Insert  the small
square (Hb) into guide (Ha). Put
together the appliance door and the
furniture door and mark the holes as
indicated in the figure. 
Remove the brackets and mark a
distance of 8 mm from the outer
edge of the door where the nail
must be fitted (K).




 

38
In case of side fixing of the
appliance, it will be sufficient to
loose the screws fixing the
bracket (E) and to position it as
shown in figure.








Place the small square on the guide
again and fix it with the screws sup-
plied.
Should the lining up of the furniture
door be necessary, use the clearance
of slots.
At the end of operations, it is neces-
sary to check if the door of the fur-
niture closes properly.






Fix cover (Hd) on guide (Hb) until it
clips into place.
 

39
Electrical connection
Before initial start-up, refer to the appliance rating plate to ascertain if sup-
ply voltage and current values correspond with those of the mains at the
installation location.
e.g.:  AC 220 ... 240 V 50 Hz or
220 ... 240 V~ 50 Hz
(i.e. 220 to 240 volts alternating current, 50 Hertz)
The rating plate is inside the appliance on the left.
A correctly installed, earthed socket is required for the electrical supply. The
supply must have a fuse rating of at least 10 Amps.
If the...

40
Control panel of freezer compartment
	



 
 
A. Operating light (green)
B. Fast freezing light (yellow)
C. Alarm light (red)
D. Fast freezing knob
E. Temperature regulator knob
The control panel elements are:the temperature regulator knob (E)is  also
the on/off switch for the freezer compartment.
The green pilot light (A),which comes on when the mains voltage is avail-
ble. Switch the temperature regulator knob to a number position, the refri-
gerating unit automatically operates by system...