AEG S 83200 Cmm0 User Manual

							ProblemPossible causeSolution
dEMo appears on the
display.The appliance is in demonstra-
tion mode.Keep pressed approximately 10
sec the OK button since a long
sound of buzzer is heard and the
display shut off for a short while:
appliance start works regularly.
As much as the advice does not lead to result, call the nearest brand-mark service.
Closing the door
1. Clean the door gaskets.
2. If necessary, adjust the door. Refer to Installation.
3. If necessary, replace the defective door gaskets. Contact the Service Center.
TECHNICAL DATA
  S83200CMM0S83600CMM0
Dimension   
 Height1850 mm2010 mm
 Width595 mm595 mm
 Depth658 mm658 mm
Rising Time 18 h18 h
Voltage 230 - 240 V230 - 240 V
Frequency 50 Hz50 Hz
The technical information are situated in the rating plate on the internal left side of the
appliance and in the energy label.
INSTALLATION
WARNING!
Read the Safety Information carefully for your safety and correct operation of the appli-
ance before installing the appliance.
Positioning
Install this appliance at a location where the ambient temperature corresponds to the cli-
mate class indicated on the rating plate of the appliance:Technical data
21
 
						

							Climate classAmbient temperature
SN+10°C to + 32°C
N+16°C to + 32°C
ST+16°C to + 38°C
T+16°C to + 43°C
Location
The appliance should be installed well away from
sources of heat such as radiators, boilers, direct
sunlight etc. Ensure that air can circulate freely
around the back of the cabinet. To ensure best
performance, if the appliance is positioned below
an overhanging wall unit, the minimum distance
between the top of the cabinet and the wall unit
must be at least 100 mm . Ideally, however, the
appliance should not be positioned below over-
hanging wall units. Accurate levelling is ensured
by one or more adjustable feet at the base of the
cabinet.
WARNING!
It must be possible to disconnect the appliance
from the mains power supply; the plug must therefore be easily accessible after installation.
Electrical connection
Before plugging in, ensure that the voltage and frequency shown on the rating plate corre-
spond to your domestic power supply.
The appliance must be earthed. The power supply cable plug is provided with a contact for
this purpose. If the domestic power supply socket is not earthed, connect the appliance to a
separate earth in compliance with current regulations, consulting a qualified electrician.
The manufacturer declines all responsibility if the above safety precautions are not ob-
served.
This appliance complies with the E.E.C. Directives.
AB
mm
mm
min100
20
22Installation
 
						

							Rear spacers
You can find the two spacers in the bag with doc-
umentation.
Do these steps to install the spacers:
1. Release the screw.
2. Engage the spacer below the screw.
3. Turn the spacer to the right position.
4. Tighten again the screws.
Levelling
When placing the appliance ensure that it stands
level. This can be achieved by two adjustable feet
at the bottom in front.
2
431
Installation23
 
						

							Removing the shelf holders
Your appliance is equipped with shelf retainers
that make it possible to secure the shelves during
transportation.
To remove them proceed as follows:
1. Move the shelf holders in the direction of the
arrow (A).
2. Raise the shelf from the rear and push it for-
ward until it is freed (B).
3. Remove the retainers (C).
Installation of the CleanAir Control filter
The CleanAir Control filter is an active car-
bon filter which absorbs bad odours and per-
mits to maintain the best flavour and aroma
for all foodstuffs without risk of odour cross
contamination.
On delivery the carbon filter is in a plastic
bag to maintain it’s duration and character-
istics. The filter should be placed behind the
flap before the appliance is turned on.
1. Open the flap cover.
2. Remove the filter from the plastic bag.
3. Insert the filter in the slot found in the
back of the flap cover.
4. Close the flap cover.
The filter should be handled carefully so fragments do not loosen from the surface. The fil-
ter should change once every six months.
Door reversibility
In case you want to change the opening direction of the door, contact the nearest After
Sales Service Force. The After Sales Service specialist will carry out the reversibility of the
doors at your cost.
ENVIRONMENTAL CONCERNS
The symbol  on the product or on its packaging indicates that this product may not be
treated as household waste. Instead it should be taken to the appropriate collection point
A
B
C
24Environmental concerns
 
						

							for the recycling of electrical and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste
handling of this product. For more detailed information about recycling of this product,
please contact your local council, your household waste disposal service or the shop where
you purchased the product.
25
 
						

							26
 
						

							27
 
						

							www.aeg.com/shop210621382-A-022011