AEG S 76372 Kg Operating Instructions

							818 34 51-00/759
Installation
Installation Location
The appliance should be installed in a well ventilated, dry room.
Energy use and efficient performance of the appliance is affected by 
the ambient temperature.
The appliance should therefore
– not be exposed to direct sunlight;
– not be installed next to radiators, cookers or other sources of heat;
– only be installed at a location whose ambient temperature 
corresponds to the climate classification, for which the appliance is 
designed.
The climate classification can be found on the rating plate, which is 
located at the left on the inside of the appliance.
The following table shows which ambient temperature is correct for 
each climate classification:
If installation next to a source of heat is unavoidable, the following 
minimum clearances must be maintained at the sides of the appliance:
– for electric cookers 3 cm;
– for oil and coal fired ranges 30 cm.
If these clearances cannot be maintained a heat insulating pad is requi-
red between the cooker and the refrigeration appliance.
Climate classificationfor an ambient temperature of
SN+10 to +32 °C
N+16 to +32 °C
ST+18 to +38 °C
T+18 to +43 °C
 
						

							Installation
60818 34 51-00/7
The refrigerator/freezer needs ventilation
Air is fed under the door through the 
vent slots in the base and is exhausted 
upwards along the back wall. To ensure 
proper air circulation never cover or 
alter the vent openings.
Important!  If the appliance is installed 
under a hanging cabinet, a clearance of 
at least 10 cm between the top of the 
appliance and the cabinet above it must 
be maintained.
Please check whether, after installing 
your appliance and especially after 
reversing the door, the door seal seals 
tightly. A badly fitting door seal may 
lead to heavy frosting and a higher 
power consumption (see also What to 
do if ...“).
Remove the two wall spacers from 
the appliance accessories pack and, 
in accordance with the illustrations, 
fix them at the top of the rear of the 
appliance so that the distance from 
the wall required for the necessary 
ventilation is ensured. 
Appliance Alignment
0 1.The appliance must be level. Please compensate for unevenness in the 
floor by turning the two adjustable feet at the front. 
Electrical Connection
A properly installed socket outlet with earthing contact is required for 
electrical connection. Electrical fuse protection must be of at least 10 
ampere.
If the outlet socket is no longer accessible after installation of the 
appliance, appropriate measures must be taken during electrical instal-
lation to assure that the appliance can be disconnected from the mains 
(e.g. fuse, circuit breaker, non-operate current safety-switch or the like, 
with a contact opening of at least 3 mm).
 
						

							Installation
818 34 51-00/761
0 1.Before initial start-up, refer to the appliance rating plate to ascertain if 
supply voltage and current values correspond with those of the mains 
at the installation location.
e.g.: AC 220 ... 240 V 50 Hz or
 220 ... 240 V~50 Hz
(i.e. 220 to 240 volts alternating current, 50 Hertz)
The rating plate is inside the appliance at the left. 
Warning: To avoid potential danger, if the mains connection lead of 
this appliance is damaged, it must be replaced by our customer service 
representative or a person with similar qualifications. 
Warning: Under no circumstances should the appliance be connected 
to electronic “power saving plugs” or to a.c.-d.c. converters which con-
vert direct current to 230 V alternating current (e.g., solar installations, 
ship networks)
Installation of the carbon filter
On delivery the carbon filter is placed 
in a plastic bag to secure the length of 
life of the carbon filter. The filter 
should be placed behind the grill 
before the cabinet is turned on. 
0 1.The cover can be opened by simultane-
ously pressing the lever on the right of 
grill (1) and turning the cover outward 
(2). 
2.The carbon filter is then mounted in 
the slot found in the back of the cover 
(3).
1 The filter should be handled carefully 
so fragments don´t loosen from the 
surface.
 
						

							62818 34 51-00/7
Reversing The Door 
The door hinges can be changed from right (as supplied) to left if 
required to suit the location where the appliance is installed. 
1 Warning! Unplug from the mains, before reversing the door. 
0 1.Open the freezer compartment 
door and remove the plinth to 
the front. Move the door bearing 
cover on the plinth from the left 
to the right. 
2.Close the freezer compartment 
door. Open the fridge compart-
ment door and unscrew the 
retaining screw for the self-clos-
ing mechanism on the top of the 
freezer compartment door. 
3.With the freezer compartment 
door closed, remove the cross-
head screws from the lower door 
bearing and remove the door 
bearing downwards. 
4.Move the bearing pivot from the 
right to the left hand hole. 
Remove the freezer compartment 
door carefully to the front and 
place on one side. 
 
						

							Reversing The Door
818 34 51-00/763
5.Unscrew the centre door bearing. 
6.Remove the fridge compartment 
door carefully to the front and 
place on one side. 
7.Unscrew the retaining screw for 
the self-closing mechanism on the 
bottom of the fridge compart-
ment door. 
8.Move the upper bearing pivot to 
the left. 
9.Push the cover on the door handle 
to the left and remove it by bring-
ing it towards you.
 
						

							Reversing The Door
64818 34 51-00/7
10.Unscrew the door handle, turn it 
180° and screw it back on to the 
right-hand side of the door.
11 .Replace the cover for the door 
handle and push it towards the 
left as far as it will go.
12.Fasten the self-closing mechanism 
to the bottom left of the fridge 
compartment door.
13.Carefully slide the fridge com-
partment door onto the top bear-
ing pivot and close. 
 
						

							Reversing The Door
818 34 51-00/765
14.Slide the centre door bearing into 
the bottom left of the fridge com-
partment door and fasten to the 
housing. 
15.Fasten the self-closing mechanism 
on the top left of the freezer 
compartment door, 
16.Carefully slide the freezer com-
partment door onto the centre 
bearing pivot and close. 
17.Place the lower door bearing with 
the bearing pivot in the lower left 
of the freezer compartment door 
and fasten. 
18.Open the freezer compartment 
door and fit the plinth. 
 
						

							66818 34 51-00/7
Appliance Description
View of Appliance
(various models)
áControl panel 
àButter and cheese compartment with lid
âDoor storage compartments
äBottle compartment
ãLONGFRESH 0 °C cold zone
åShelves
çQuick chill shelf
éBottle and can holder
èRating plate
êGrid
ëFreezer drawer (only for storage). When defrosting the bottom 
drawer also serves as a water collecting vessel
íFreezer drawer (for storage and freezing) 
ìFreezer tray
 
						

							Appliance Description
818 34 51-00/767
Freezer tray 
A freezer tray  is included below the 
upper drawer in the freezer 
compartment.
Berries and vegetables, for example, 
can be pre-frozen on the freezer tray.
Advantage: The berries are not squeezed and maintain their natural 
form. The frozen berries can then be stored in compartments or drawers 
packaged in individual portions. 
Cold Accumulation Block
A cold accumulation block is enclosed with the appliance.
3 In the event of power failure or a malfunction of the appliance, the 
cold accumulation block will increase the hold over period by several 
hours. The cold accumulation block will be most effective when placed 
at the front of the upper freezer tray. 
When defrosting the appliance place the cold accumulation block on 
top of the frozen food to keep it cold. 
The block may also be used in a cool bag to keep the temperature of 
food down during transportation.
Refer to the section Prior to Initial Start-Up regarding the freezing of 
the cold accumulation block.
 
						

							Appliance Description
68818 34 51-00/7
Control Panel
  1ON/OFF button and ON/OFF indicator light (green)
  2Temperature display for refrigerator (not for LONGFRESH 0 °C 
cold zone)
  3Temperature setting buttons for refrigerator 
  4COOLMATIC button and COOLMATIC indicator light (yellow) 
 COOLMATIC for intensive cooling in the refrigerator
  5FROSTMATIC button and FROSTMATIC indicator light (yellow)
 FROSTMATIC for fast freezing in the freezer compartment
  6Temperature display for freezer compartment 
  7Temperature setting buttons for freezer compartment
  8ALARM OFF button and warning indicator light (red)
(see section: Control and Information Systems)
Temperature setting buttons
The temperature is adjusted using the 
„+“ (WARMER) and „-“ (COLDER) buttons.
These buttons are connected to the temperature display.
 The temperature display is switched over from the display of the 
ACTUAL temperature (Temperature display is illuminated) to the dis-
play of the DESIRED temperature (Temperature display flashes) by 
pressing one of the two buttons, „+“ (WARMER) or „-“ (COLDER). 
 Each time one of the two buttons is pressed again the DESIRED tem-
perature is adjusted by 1 °C.
 If neither button is pressed, the temperature display automatically 
switches back after a short period (approx. 5 sec.) to the display of 
the ACTUAL temperature.
DESIRED temperature means: 
The temperature that has been selected for inside the fridge or the 
freezer compartment. The DESIRED temperature is indicated by flashing 
numbers.