AEG S 75328 Dt2 User Manual

• pull out of the slot the exhausted air filter.
•
2
1
insert the new air filter in the slot (2)
•close the flap.
The air filter is a consumable accessory and as such is not covered by the guarantee.
During the operation, always keep the air ventilation flap closed.
The air filter should be handled carefully to prevent its surface from being scratched.
Defrosting of the refrigerator
Frost is automatically eliminated from the evaporator of the refrigerator compartment
every time the motor compressor...

It is important to periodically clean the defrost
water drain hole in the middle of the refrigerator
compartment channel to prevent the water over-
flowing and dripping onto the food inside. Use the
special cleaner provided, which you will find al-
ready inserted into the drain hole.
Defrosting of the freezer
The freezer compartment of this model, on the other hand, is a no frost type. This means
that there is no buildup of frost when it is in operation, neither on the internal walls nor
on the foods....

ProblemPossible causeSolution
 The mains plug is not connected
to the mains socket correctly.Connect the mains plug to the
mains socket correctly.
 The appliance has no power.
There is no voltage in the mains
socket.Connect a different electrical ap-
pliance to the mains socket.
Contact a qualified electrician.
The lamp does not work.The lamp is in stand-by.Close and open the door.
 The lamp is defective.Refer to Replacing the lamp.
The compressor operates
continually.The temperature is not set cor-...

ProblemPossible causeSolution
There is too much frost.Food is not wrapped correctly.Wrap the food correctly.
 The door is not closed correctly.Refer to Closing the door.
 The temperature regulator is not
set correctly.Set a higher temperature.
Replacing the lamp
CAUTION!
Disconnect the plug from the mains socket.
1. Press on the rear hook of the lamp cover by a
screwdriver and at the same time pull and ro-
tate the cover in the direction of the arrow.
2. Replace the lamp with one of the same power
(the...

Positioning
Install this appliance at a location where the ambient temperature corresponds to the
climate class indicated on the rating plate of the appliance:
Climate classAmbient temperature
SN+10°C to + 32°C
N+16°C to + 32°C
ST+16°C to + 38°C
T+16°C to + 43°C
Location
The appliance should be installed well away from sources of heat such as radiators, boilers,
direct sunlight etc. Ensure that air can circulate freely around the back of the cabinet. To
ensure best performance, if the appliance is...

This appliance complies with the E.E.C. Directives.
Rear spacers
Inside the appliance you find two spacers
which must be fitted as shown in the figure.
Slacken the screws and insert the spacer under the
screw head, then retighten the screws.
Installation of the Taste Guard Filter
The Taste Guard Filter is an active carbon filter which absorbs bad odours and permits to
maintain the best flavour and aroma for all foodstuffs without risk of odour cross con-
tamination.
On delivery the carbon filter is in a...

1. Screw the top handle bracket to the han-
dle rod.
2. Fit the bottom handle bracket on the low-
er right-hand side of the door.
3. Fit the top handle bracket on the top
right-hand side of the door.
4. Screw the handle rod to the bottom han-
dle bracket.
Do not use excessive force and overtighten the
screws (max. 2 Nm) as you may damage the
door handles.
Removing the shelf holders
Your appliance is equipped with shelf retainers
that make it possible to secure the shelves during
transportation.
To remove...

1. Slide the bottom door off the middle
hinge (H). Remove the middle hinge by
unscrewing the fixing screws.
Make sure to remove the plastic spacer
inserted under the hinge.
2. Slide the top door off the pin (G). Un-
screw the pin (G) and install it on the
opposite side.
3. Remove the two plugs from the middle
crossbeam and install them on the op-
posite side, covering the holes left free
from the removed hinge.
4. Remove the plugs (1) on the upper side
of both doors and move them to the
other side.
H
G...

5. Remove with a tool the cover (e), un-
screw the lower hinge pivot (f) using a
10 mm spanner and re-screw it on the
opposite side.
6. Install the cover (e) on the opposite side.
7. Remove the handle. Unscrew the top
handle bracket from the handle rod (h1).
Unscrew the bottom handle bracket
from the door (h2). Unscrew the top
handle bracket from the door (h3).
Install the plug (1).
8. Install the handle in the opposite side.
Re-screw the handle bracket on the door
(h4). Turn the handle bracket with the...

for the recycling of electrical and electronic equipment. By ensuring this product is disposed
of correctly, you will help prevent potential negative consequences for the environment
and human health, which could otherwise be caused by inappropriate waste handling of
this product. For more detailed information about recycling of this product, please contact
your local council, your household waste disposal service or the shop where you purchased
the product.
20