AEG S 70318 Kg5 User Manual

Vegetable Drawer
The drawer is suitable for storing fruit and vege-
tables.
There is a separator inside the drawer that can be
placed in different positions to allow for the sub-
division best suited to personal needs.
There is a grille (if foreseen) on the bottom of the
drawer to separate the fruit and vegetables from
any humidity that may form on the bottom sur-
face.
All parts inside the drawer can be removed for
cleaning purposes
Humidity control
The glass shelf incorporates a device with slits...

Hints for refrigeration
Useful hints:
Meat (all types) : wrap in polythene bags and place on the glass shelf above the vegetable
drawer.
For safety, store in this way only one or two days at the most.
Cooked foods, cold dishes, etc..: these should be covered and may be placed on any shelf.
Fruit and vegetables: these should be thoroughly cleaned and placed in the special drawer(s)
provided.
Butter and cheese: these should be placed in special airtight containers or wrapped in
aluminium foil or polythene...

This appliance contains hydrocarbons in its cooling unit; maintenance and recharging must
therefore only be carried out by authorized technicians.
Periodic cleaning
The equipment has to be cleaned regularly:
• clean the inside and accessories with lukewarm water and some neutral soap.
• regularly check the door seals and wipe clean to ensure they are clean and free from
debris.
• rinse and dry thoroughly.
Do not pull, move or damage any pipes and/or cables inside the cabinet.
Never use detergents,...

Defrosting the freezer
A certain amount of frost will always form on the freezer shelves and around the top
compartment.
Defrost the freezer when the frost layer reaches a thickness of about 3-5 mm.
About 12 hours prior to defrosting, set the Temperature regulator toward higher settings ,
in order to build up sufficient chill reserve for the interruption in operation.
To remove the frost, follow the instructions below:
1. Switch off the appliance.
2. Remove any stored food, wrap it in several layers of...

What to do if…
WARNING!
Before troubleshooting, disconnect the mains plug from the mains socket.
Only a qualified electrician or competent person must do the troubleshooting that is not
in this manual.
There are some sounds during normal use (compressor, refrigerant circulation).
ProblemPossible causeSolution
The appliance does not
operate. The lamp does
not operate.The appliance is switched off.Switch on the appliance.
 The mains plug is not connected
to the mains socket correctly.Connect the mains plug...

ProblemPossible causeSolution
 The door is not closed correctly.Refer to Closing the door.
 The product temperature is too
high.Let the product temperature de-
crease to room temperature be-
fore storage.
 Many products are stored at the
same time.Store less products at the same
time.
The temperature in the
refrigerator is too high.There is no cold air circulation in
the appliance.Make sure that there is cold air
circulation in the appliance.
The temperature in the
freezer is too high.Products are too...

Technical data
   
Dimension of the recess  
 Height1850 mm
 Width600 mm
 Depth625 mm
Rising Time 30 h
The technical information are situated in the rating plate on the internal left side of the
appliance and in the energy label.
Installation
WARNING!
Read the Safety Information carefully for your safety and correct operation of the ap-
pliance before installing the appliance.
Positioning
Install this appliance at a location where the ambient temperature corresponds to the
climate class indicated on the...

Electrical connection
Before plugging in, ensure that the voltage and frequency shown on the rating plate cor-
respond to your domestic power supply.
The appliance must be earthed. The power supply cable plug is provided with a contact for
this purpose. If the domestic power supply socket is not earthed, connect the appliance to
a separate earth in compliance with current regulations, consulting a qualified electrician.
The manufacturer declines all responsibility if the above safety precautions are not...

Fitting the door handles
The handles are supplied as a kit at delivery.
1. Screw the top handle bracket to the han-
dle rod.
2. Fit the bottom handle bracket on the low-
er right-hand side of the door.
3. Fit the top handle bracket on the top
right-hand side of the door.
4. Screw the handle rod to the bottom han-
dle bracket.
Do not use excessive force and overtighten the
screws (max. 2 Nm) as you may damage the
door handles.
Door reversibility
WARNING!
Before carrying out any operations, remove the...

2. Slide the bottom door off the middle
hinge (H). Remove the middle hinge by
unscrewing the fixing screws.
3. Slide the top door off the pin (G). Un-
screw the pin (G) and install it on the
opposite side.
4. Remove the two plugs from the middle
crossbeam and install them on the op-
posite side, covering the holes left from
the removed hinge.
5. Remove the plugs (1) on the upper side
of both doors and move them to the
other side.
6. Remove the handle. Unscrew the top
handle bracket from the handle rod...