AEG Oven BP531450KM User Manual

							FoodTemperature
(°C)Time (h)Shelf position1 position2 positionsVegetables for
sour60 - 705 - 631 / 4Mushrooms50 - 606 - 831 / 4Herbs40 - 502 - 331 / 4
Fruit
FoodTemperature
(°C)Time (h)Shelf position1 position2 positionsPlums60 - 708 - 1031 / 4Apricots60 - 708 - 1031 / 4Apple slices60 - 706 - 831 / 4Pears60 - 706 - 931 / 49.17  Core temperature sensor table
Beef
FoodFood core temperature (°C)Rib / Fillet steak: rare45 - 50Rib / Fillet steak: medium60 - 65Rib / Fillet steak: well done70 - 75
Pork
FoodFood core temperature (°C)Shoulder / Ham / Neck joint of pork80 - 82Chop (saddle) / Smoked pork loin75 - 80Meatloaf75 - 80
Veal
FoodFood core temperature (°C)Roast veal75 - 80Knuckle of veal85 - 90
Mutton / lamb
FoodFood core temperature (°C)Leg of mutton80 - 85ENGLISH31 
						

							FoodFood core temperature (°C)Saddle of mutton80 - 85Roast lamb / Leg of lamb70 - 75
Game
FoodFood core temperature (°C)Saddle of hare70 - 75Leg of hare70 - 75Whole hare70 - 75Saddle of venison70 - 75Leg of venison70 - 75
Fish
FoodFood core temperature (°C)Salmon65 - 70Trouts65 - 7010. CARE AND CLEANINGWARNING!
Refer to Safety chapters.10.1  Notes on cleaning
• Clean the front of the appliance with a
soft cloth with warm water and a
cleaning agent.
• To clean metal surfaces, use a dedicated cleaning agent.
• Clean the appliance interior after each use. Fat accumulation or other
food remains may result in a fire. The
risk is higher for the grill pan.
• Clean stubborn dirt with a special oven cleaner.
• Clean all accessories after each use and let them dry. Use a soft cloth withwarm water and a cleaning agent.
• If you have nonstick accessories, do not clean them using aggressive
agents, sharp-edged objects or a dishwasher. It can cause damage to
the nonstick coating.
10.2  Removing the shelf
supports
To clean the oven, remove the shelf
supports.
1. Pull the front of the shelf support
away from the side wall.
2. Pull the rear end of the shelf support
away from the side wall and remove
it.
www.aeg.com32   
						

							Install the shelf supports in the opposite
sequence.
The retaining pins on the
telescopic runners must
point to the front.10.3  PyrolysisCAUTION!
Do not start the Pyrolysis if the Plus Steam button is
pressed in.CAUTION!
Remove all accessories and
removable shelf supports.Do not start the Pyrolysis if
you did not fully close the
oven door. In some models,
the display shows "C3"
when this error occurs.WARNING!
The appliance becomes very
hot. There is a risk of burns.CAUTION!
If there are other appliances installed in the same
cabinet, do not use them
when the Pyrolysis function
operates. It can cause
damage to the appliance.
1. Remove the worst dirt manually.
2. Clean the inner side of the door with
hot water, so that the residues do not
burn from the hot air.
3. Set the Pyrolysis function. Refer to
"Oven functions".
4. When 
 flashes, press  or  to
set the necessary procedure:
OptionDescriptionP1If the oven is
not very dirty.
Time of the
procedure: 1
h 30 min.P2If you cannot
easily remove
the dirt. Time
of the proce-
dure: 2 h 30
min.
You can use the End function to delay
the start of the cleaning procedure.
During the Pyrolysis the oven lamp is off. 5. To change the default length of the
procedure ( P1 or  P2), press 
 to set
, and then press  or  to set
the length of the cleaning procedure.
6. When the oven is at its set
temperature, the door locks. The
display shows the symbol 
 and the
bars of the heat indicator until the
door unlocks.
7. When Pyrolysis is completed, the
display shows the time of day. The
oven door stays locked.
8. When the appliance is cool again, an
acoustic signal sounds and the door
unlocks.
10.4  Cleaning reminder
To remind you that the Pyrolysis is
necessary, PYR flashes in the display for
10 seconds after each activation and
deactivation of the appliance.
The cleaning reminder
goes out:
• after the end of the Pyrolysis function.
• if you press 
 and  at
the same time while PYR
flashes in the display.
ENGLISH332
1                   
						

							10.5 Removing and installing
the door
You can remove the door and the
internal glass panels to clean it. The number of glass panels is different fordifferent models.WARNING!
Be careful when you remove
the door from the appliance.
The door is heavy.
1. Open the door fully.
2. Fully press the clamping levers (A) on
the two door hinges.
3. Close the oven door to the first
opening position (approximately 70°
angle).
4. Hold the door with one hand on each
side and pull it away from the
appliance at an upwards angle.
5. Put the door with the outer side
down on a soft cloth on a stable
surface. This is to prevent scratches.
6. Hold the door trim (B) on the top
edge of the door at the two sides
and push inwards to release the clip
seal.
7. Pull the door trim to the front to
remove it.
8. Hold the door glass panels on their
top edge one by one and pull them
up out of the guide.
9. Clean the glass panel with water and
soap. Dry the glass panel carefully.
When the cleaning is completed, do the
above steps in the opposite sequence.
Install the smaller panel first, then the
larger and the door.
WARNING!
Make sure that the glasses
are inserted in the correct
position otherwise the
surface of the door may
overheat.
Make sure that you put the glass panels (C, B and A) back in the correct
sequence. First, insert panel C, which has
a square printed on the left side and a
triangle on the right side. You will also
find those symbols embossed on the
door frame. The triangle symbol on the
glass must match the triangle on the
door frame, and the square symbol must match the square. After that insert the
other two glass panels.
www.aeg.com34 AA 1
2
B   A B C   
						

							10.6 Replacing the lamp
Put a cloth on the bottom of the interior
of the appliance. It prevents damage to the lamp glass cover and the cavity.WARNING!
Danger of electrocution!
Disconnect the fuse before
you replace the lamp.
The lamp and the lamp glass
cover can be hot.
1. Deactivate the appliance.
2. Remove the fuses from the fuse box
or deactivate the circuit breaker.
The top lamp
1. Turn the lamp glass cover
counterclockwise to remove it.
2. Clean the glass cover.
3. Replace the lamp with a suitable 300
°C heat-resistant lamp.
4. Install the glass cover.The side lamp
1.Remove the left shelf support to get
access to the lamp.
2. Use a narrow, blunt object (e.g. a
teaspoon) to remove the glass cover.
3. Clean the glass cover.
4. Replace the lamp with a suitable 300
°C heat-resistant lamp.
5. Install the glass cover.
6. Install the left shelf support.
11.  TROUBLESHOOTINGWARNING!
Refer to Safety chapters.11.1  What to do if...ProblemPossible causeRemedyYou cannot activate or oper-
ate the oven.The oven is not connected
to an electrical supply or it is
connected incorrectly.Check if the oven is correctly
connected to the electrical
supply (refer to the connec-
tion diagram if available).The oven does not heat up.The oven is deactivated.Activate the oven.The oven does not heat up.The clock is not set.Set the clock.The oven does not heat up.The necessary settings are
not set.Make sure that the settings
are correct.The oven does not heat up.The automatic switch-off is
activated. Refer to "Automatic switch-
off". ENGLISH35     
						

							ProblemPossible causeRemedyThe oven does not heat up.The Child Lock is on.Refer to "Using the Child
Lock".The oven does not heat up.The fuse is blown.Make sure that the fuse is
the cause of the malfunction.
If the fuse is blown again
and again, contact a quali-
fied electrician.The lamp does not operate.The lamp is defective.Replace the lamp.The core temperature sensor
does not operate.The plug of the core tem-
perature sensor is not cor-
rectly installed into the sock-
et.Put the plug of the core tem-
perature sensor as far as
possible into the socket.It takes too long to cook the
dishes or they cook too
quickly.The temperature is too low
or too high.Adjust the temperature if
necessary. Follow the advice
in the user manual.Steam and condensation
settle on the food and in the
cavity of the oven.You left the dish in the oven
for too long.Do not leave the dishes in
the oven for longer than 15 -
20 minutes after the cooking
process ends.The display shows "C2".You want to start the Pyroly-
sis or Defrost function, but
you did not remove the core
temperature sensor plug
from the socket.Remove the core tempera-
ture sensor plug from the
socket.The display shows "C3".The cleaning function does
not operate. You did not
fully close the door, or the
door lock is defective.Fully close the door.The display shows "F102".• You did not fully close the door.
• The door lock is defec- tive.• Fully close the door.
• Deactivate the oven with the house fuse or the
safety switch in the fuse
box and activate it again.
• If the display shows "F102" again, contact the
Customer Care Depart-
ment.www.aeg.com36 
						

							ProblemPossible causeRemedyThe display shows an error
code that is not in this table. There is an electrical fault.• Deactivate the oven with the house fuse or the
safety switch in the fuse
box and activate it again.
• If the display shows the error code again, contact
the Customer Care De-
partment.There is no good cooking
performance using the True
Fan Cooking PLUS function.You did not activate the
True Fan Cooking PLUS
function.Refer to "Activating the True
Fan Cooking PLUS func-
tion".There is no good cooking
performance using the True
Fan Cooking PLUS function.You did not activate correct-
ly the True Fan Cooking
PLUS function with the Plus
Steam button.Refer to "Activating the True
Fan Cooking PLUS func-
tion".There is no good cooking
performance using the True
Fan Cooking PLUS function.You did not fill the cavity
embossment with water.Refer to "Activating the True
Fan Cooking PLUS func-
tion".You want to activate the
True Fan Cooking function,
but the indicator of the Plus
Steam button is on.The True Fan Cooking PLUS
function operates.Push the Plus Steam button
 to stop the True Fan
Cooking PLUS function.
You want to activate the
cleaning function, but the
display shows "C4".The Plus Steam button is
pressed in.Press the Plus Steam button
again.The water in the cavity em-
bossment does not boil.The temperature is too low.Set the temperature at least
to 110 °C.
Refer to “Hints and tips”
chapter.The water comes out of the
cavity embossment.There is too much water in
the cavity embossment.Deactivate the oven and
make sure that the appliance
is cold. Wipe the water with
a cloth or sponge. Add the
correct amount of water to
the cavity embossment. Re-
fer to the specific procedure.ENGLISH37  
						

							ProblemPossible causeRemedyThe appliance is activated
and does not heat up. The
fan does not operate. The
display shows  "Demo".The demo mode is activa-
ted.1. Deactivate the oven.
2. Press and hold the but-
ton 
.
3. The first digit on the dis- play and  Demo indicator
start to blink.
4. Enter the code 2468 by
pressing the buttons 
or  to change the val-
ues and press 
 to con-
firm.
5. The next digit starts to blink.
6. Demo  mode deactivates
when you confirm the
last digit and the code is
correct.
11.2  Service data
If you cannot find a solution to the
problem yourself, contact your dealer or
an Authorised Service Centre.
The necessary data for the service centre
is on the rating plate. The rating plate ison the front frame of the appliance
cavity. Do not remove the rating plate
from the appliance cavity.We recommend that you write the data here:Model (MOD.).........................................Product number (PNC).........................................Serial number (S.N.).........................................12.  ENERGY EFFICIENCY12.1  Product Fiche and information according to EU 65-66/2014Supplier's nameAEGModel identificationBP531450KMEnergy Efficiency Index81.2Energy efficiency classA+Energy consumption with a standard load, conven-
tional mode1.09 kWh/cyclewww.aeg.com38     
						

							Energy consumption with a standard load, fan-forced
mode0.69 kWh/cycleNumber of cavities1Heat sourceElectricityVolume71 lType of ovenBuilt-In OvenMass40.0 kgEN 60350-1 - Household electric cooking
appliances - Part 1: Ranges, ovens, steam
ovens and grills - Methods for measuring performance.12.2  Energy savingThe appliance contains
features which help you save
energy during everyday
cooking.General hints
Make sure that the oven door is closed
properly when the appliance operates
and keep it closed as much as possible
during the cooking.
Use metal dishes to improve energy
saving.
When possible, do not preheat the oven before you put the food inside.
When the cooking duration is longer
than 30 minutes, reduce the oven
temperature to minimum 3 - 10 minutes
before the end of the cooking time,
depending on the duration of the cooking. The residual heat inside the
oven will continue to cook.
Use the residual heat to warm up other
dishes.
Cooking with fan
When possible, use the cooking
functions with fan to save energy.
Residual heat
If a programme with the Duration or End
Time selection is activated and the cooking time is longer than 30 minutes,
the heating elements deactivate
automatically 10% faster in some oven
functions.
The fan and lamp continue to operate.Keep food warm
Choose the lowest possible temperature setting to use residual heat and keep ameal warm. The display shows theresidual heat indicator or temperature.
Cooking with the lamp off
Deactivate the lamp during cooking and
activate only when you need it.
Moist Fan Baking
Function designed to save energy during
cooking. It operates in such a way that
the temperature in the oven cavity may
differ from the temperature indicated on
the display during a cooking cycle and
cooking times may be different from the
cooking times in other programmes.
When you use Moist Fan Baking, the
lamp automatically deactivates after 30
seconds. You may activate the lamp
again but this action will reduce the
expected energy savings.
13.  ENVIRONMENTAL CONCERNSRecycle the materials with the symbol .
Put the packaging in applicable
containers to recycle it. Help protect the
environment and human health and torecycle waste of electrical and electronic
appliances. Do not dispose appliances
marked with the symbol 
 with the
household waste. Return the product to
ENGLISH39    
						

							your local recycling facility or contact
your municipal office.
*
www.aeg.com40