AEG Lavamat Ls 84840 User Manual

							If you are unable to identify or solve the problem,
contact our service centre. Before telephoning,
make a note of the model, serial number and pur-
chase date of your machine: the Service Centre
will require this information.
TECHNICAL DATA
DimensionsWidth / Height / Depth60 / 85 / 63 mm
Electrical connectionVoltage
Overall power
Fuse
Frequency230 V
2200 W
10 A
50 Hz
Water supply pressureMinimum
Maximum0,5 bar (0,05 MPa)
8 bar (0,8 MPa)
Level of protection against ingress of solid particles and moistureIPX4
Water supply 1) Cold water
Maximum LoadCotton6 kg
Spin SpeedMaximum1400 rpm
1) Connect the water inlet hose to a water tap with a 3/4 thread.
CONSUMPTION VALUES
ProgrammeEnergy consumption
(KWh)Water consumption
(litres)Programme duration
(Hours.Minutes)
White Cottons 95°1.9562
For the duration of
the programmes,
please refer to the
display on the control
panel.
Cottons 60°1.1558
Cotton ECO 60° 1)1.0245
Cottons 40°0.7558
Synthetics 40°0.545
Delicates 40°0.558
Wool/ Handwash 30°0.2842
1) « Cotton Eco » at 60°C with a load of 6 kg is the reference programme for the data entered in the energy label,
in compliance with EEC 92/75 standards.
Technical data31
 
						

							The consumption data shown on this chart is to be considered purely indicative, as it may
vary depending on the quantity and type of laundry, on the inlet water temperature and on
the ambient temperature.
INSTALLATION
Unpacking
All transit bolts and packing must be removed before using the appliance.
You are advised to keep all transit devices so that they can be refitted if the machine ever
has to be transported again.
1. After removing all the packaging, care-
fully lay machine on it’s back to remove
the polystyrene base from the bottom.
2. Remove the power supply cable and the
draining and inlet hose from the hose
holders on the rear of the appliance.
32Installation
 
						

							3. Unscrew the three bolts with the key
supplied with the appliance.
4. Slide out the relevant plastic spacers.
5. Fill the smaller upper hole and the two
large ones with the corresponding plas-
tic plug caps supplied in the bag con-
taining the instruction booklet.
Installation33
 
						

							Positioning and levelling
Install the machine on a flat hard floor.
Make sure that air circulation around the machine
is not impeded by carpets, rugs etc.
Before placing it on small tiles, apply a rubber
coating.
Never try to correct any unevenness in the floor
by putting pieces of wood, cardboard or similar
materials under the machine.
If it is impossible to avoid positioning the machine
next to a gas cooker or coalburning stove, an in-
sulating panel covered with aluminium foil on the
side facing the cooker or stove, must be inserted
between the two appliances.
The machine must not be installed in rooms where the temperature can drop below 0°C.
The water inlet hose and the drain hose must not be kinked.
Please ensure that when the appliance is installed, it is easily accessible for the engineer in
the event of a breakdown.
Carefully level by screwing the adjustable feet in or out. Never place cardboard, wood or
similar materials under the machine to compensate for any unevenness in the floor.
Water inlet
An inlet hose is supplied and can be found inside the machine drum.
This appliance must be connected to a cold water supply.
Do not use the hose from your previous machine to connect to the water supply.
1. Open the porthole and extract the inlet
hose.
2. Connect the hose with the angled con-
nection to the machine.
Do not place the inlet hose downwards.
Angle the hose to the left or right depend-
ing on the position of your water tap.
34Installation
 
						

							3. Set the hose correctly by loosening the
ring nut. After positioning the inlet
hose, be sure to tighten the ring nut
again to prevent leaks.
4. Connect the hose to a tap with a 3/4”
thread. Always use the hose supplied
with the appliance.
The inlet hose must not be lengthened. If it is
too short and you do not wish to move the
tap, you will have to purchase a new, longer
hose specially designed for this type of use.
Installation should comply with local water
authority and building regulations require-
ments. Check the minimum water pressure
required for safe operation of the appliance
in the chapter Technical Data.
Water-stop device
The inlet hose is provided with a water stop de-
vice, which protects against damage caused by
water leaks in the hose which could develop due
to natural ageing of the hose. This fault is shown
by a red sector in the window «A». Should this oc-
cur, turn the water tap off and refer to your Serv-
ice Centre to replace the hose.
Water drainage
The end of the drain hose can be positioned in three ways:
1.Hooked over the edge of a sink using the plastic hose guide supplied with the ma-
chine.
In this case, make sure the end cannot come unhooked when the machine is emptying.
A
Installation35
 
						

							This could be done by tying it to the tap
with a piece of string or attaching it to
the wall.
2.In a sink drain pipe branch. This branch
must be above the trap so that the bend
is at least 60 cm above the ground.
3.Directly into a drain pipe at a height
of not less than 60 cm and not more
than 90 cm.
The end of the drain hose must always be
ventilated, i.e. the inside diameter of the
drain pipe must be larger than the outside
diameter of the drain hose.
The drain hose must not be kinked.
The drain hose may be extended to a maximum of 4 metres. An additional drain hose and
joining piece is available from your local Service Centre.
ELECTRICAL CONNECTION
Information on the electrical connection is given on the rating plate on the inner edge of
the appliance door.
Check that your domestic electrical installation can take the maximum load required, also
taking into account any other appliances in use.
WARNING!
Connect the machine to an earthed socket.
WARNING!
The manufacturer does not accept any responsibility for damage or injury through fail-
ure to comply with the above safety precaution.
WARNING!
The power supply cable must be easily accessible after installing the machine.
36Electrical connection
 
						

							WARNING!
Should the appliance power supply cable need to be replaced, this must be carried out
by a Service Centre.
ENVIRONMENT CONCERNS
The symbol  on the product or on its packaging indicates that this product may not be
treated as household waste. Instead it should be taken to the appropriate collection point
for the recycling of electrical and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste
handling of this product. For more detailed information about recycling of this product,
please contact your local council, your household waste disposal service or the shop where
you purchased the product.
Packaging materials
The materials marked with the symbol  are recyclable.
>PEPSPP
						

							38
 
						

							39
 
						

							www.aeg.com/shop132957921-A-202011