AEG Lavamat Ls 70840 User Manual

Red wine: soak in water and detergent, rinse and treat with acetic or citric acid, then rinse.
Treat any residual marks with bleach.
Ink: depending on the type of ink, moisten the fabric first with acetone
1), then with acetic
acid; treat any residual marks on white fabrics with bleach and then rinse thoroughly.
Tar stains: first treat with stain remover, methylated spirits or benzine, then rub with de-
tergent paste.
Detergents and additives
Good washing results also depend on the choice of detergent...

Descaling
The water we use normally contains lime. It is a good idea to periodically use a water soft-
ening powder in the machine. Do this separately from any laundry washing, and according
to the softening powder manufacturers instructions. This will help to prevent the forma-
tion of lime deposits.
After each wash
Leave the door open for a while. This helps to prevent mould and stagnant smells forming
inside the appliance. Keeping the door open after a wash will also help to preserve the door
seal....

Washing drum
Rust deposits in the drum may occur due to rusting foreign bodies in the washing or tap
water containing iron.
Do not clean the drum with acidic descaling agents, scouring agents containing chlorine or
iron or steel wool.
1. Remove any rust deposits on the drum with a cleaning agent for stainless steel.
2. Run a washing cycle without any washing to clean off any cleaning agent residues.
Programme: Short Cotton Programme at maximum temperature and add approx. 1/4
measuring cup of detergent....

6. Pull out the emergency emptying hose,
place it in the container and remove its
cap.
7. When no more water comes out, un-
screw the pump cover by turning it an-
ti-clockwise and remove the filter. Use
pliers, if necessary. Always keep a rag
nearby to dry up any water spillages
when removing the cover.
Clean the filter under a tap, to remove
any traces of fluff.
8. Remove foreign bodies and fluff from
the filter seat and from the pump im-
peller.
9. Check carefully whether the pump im-
peller rotates...

When the appliance is in use and depending on the programme selected there can be hot
water in the pump.
Never remove the pump cover during a wash cycle, always wait until the appliance has fin-
ished the cycle, and is empty. When refitting the pump cover, ensure it is securely re-tight-
ened so as to stop leaks and young children being able to remove it.
Cleaning the water inlet filters
If the appliance doesnt fill, it takes a long time to fill with water, the starting button blinks
yellow or the...

7. Screw the hose back to the machine and
make sure the connection is tight.
8. Turn on the water tap.
Emergency emptying out
If the water is not discharged, proceed as follows to empty out the machine:
1. pull out the plug from the power socket;
2. close the water tap;
3. if necessary, wait until the water has cooled down;
4. open the pump door;
5. place a bowl on the floor and place the end of the emergency emptying hose into the
bowl. Remove its cap. The water should drain by gravity into the bowl....

WHAT TO DO IF…
Certain problems are due to lack of simple maintenance or oversights, which can be solved
easily without calling out an engineer. Before contacting your local Service Centre, please
carry out the checks listed below.
During machine operation it is possible that the yellow pilot light of button 7 blinks, one of
the following alarm codes appears on the display and at the same time some acoustic sig-
nals sound every 20 seconds to indicate that the machine is not working:
•
 : problem with...

ProblemPossible cause/Solution
The machine does not empty and/or does not
spin:
The drain hose is squashed or kinked. • Check the drain hose connection.
The drain filter is clogged. 
• Clean the drain filter.
An option or a programme that ends with the
water still in the tub or a that eliminates all the
spinning phases has been selected.
• Select the draining or the spinning pro-
gramme.
The laundry is not evenly distributed in the
drum.
• Redistribute the laundry.
There is water on the floor:
Too much...

ProblemPossible cause/Solution
The machine vibrates or is noisy:
The transit bolts and packing have not been re-
moved.
• Check the correct installation of the appli-
ance.
The support feet have not been adjusted
• Check the correct levelling of the appliance.
The laundry is not evenly distributed in the
drum.
• Redistribute the laundry.
Maybe there is very little laundry in the drum.
• Load more laundry.
Spinning starts late or the machine does not
spin:
The electronic unbalance detection device has
cut...

If you are unable to identify or solve the problem,
contact our service centre. Before telephoning,
make a note of the model, serial number and pur-
chase date of your machine: the Service Centre
will require this information.
TECHNICAL DATA
DimensionsWidth
Height
Depth60 cm
85 cm
45 cm
Electrical connectionInformation on the electrical connection is given on the rating
plate, on the inner edge of the appliance door.
Water supply pressureMinimum
Maximum0,05 MPa
0,8 MPa
Maximum LoadCotton6 kg
Spin...