AEG Lavamat Ls 60840l User Manual

6. When no more water comes out, un‐screw the pump and remove it. Always
keep a rag nearby to dry up spillage of
water when removing the pump.
7. Remove any objects from the pump impeller by rotating it.
8. Put the cap back on the emergency emp‐
tying hose and place the latter back in
its seat.
9. Screw the pump fully in.
10. Close the pump door.
WARNING!
When the appliance is in use and depending on the programme selected there can be hot
water in the pump. Never remove the pump cover during a wash...

1. Turn off the water tap.
2. Unscrew the hose from the tap.
3. Clean the filter in the hose with a stiff brush.
4. Screw the hose back onto the tap. Make sure the connection is tight.
5. Unscrew the hose from the machine. Keep
a rug nearby because some water may
flow.
6. Clean the filter in the valve with a stiff brush or with the piece of cloth.
7. Screw the hose back to the machine and make sure the connection is tight.
8. Turn on the water tap.
Emergency emptying out If the water is not discharged,...

is full, put the cap back on the hose. Empty the bowl. Repeat the procedure until water
stops flowing out;
6. clean the pump if necessary as previously described;
7. replace the emergency emptying hose in its seat after having plugged it;
8. screw the pump again and close the door.
Frost precautions If the machine is installed in a place where the temperature could drop below 0°C, proceed
as follows:
1. close the water tap and unscrew the water inlet hose from the tap;
2. place the end of the emergency...

ProblemPossible cause/Solution
The washing machine does not start:
The door has not been closed. • Close the door firmly.
The plug is not properly inserted in the power
socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical instal‐ lation.
The main fuse has blown.
• Replace the fuse.
The selector dial is not correctly positioned and
the button  8 has not been depressed.
• Please turn the selector dial and press the
button  8 again.
The...

ProblemPossible cause/Solution
There is water on the floor:
Too much detergent or unsuitable detergent
(creates too much foam) has been used.
• Reduce the detergent quantity or use anoth‐
er one.
Check whether there are any leaks from one of
the inlet hose fittings. It is not always easy to
see this as the water runs down the hose; check
to see if it is damp.
• Check the water inlet hose connection.
The drain hose is damaged.
• Change it with a new one.
The cap on the emergency emptying hose has
not been...

ProblemPossible cause/Solution
Spinning starts late or the machine does not
spin:
The electronic unbalance detection device has
cut in because the laundry is not evenly distrib‐
uted in the drum. The laundry is redistributed
by reverse rotation of the drum. This may hap‐
pen several times before the unbalance disap‐
pears and normal spinning can resume. If, after
some minutes, the laundry is still not evenly
distributed in the drum, the machine will not
spin.
• Redistribute the laundry.
The load is too...

Water supply pressureMinimum
Maximum0,05 MPa
0,8 MPaMaximum LoadCotton6 kgSpin SpeedMaximum1000 rpm (LS 60840 L)
1200 rpm (LS 62840 L)
Consumption values
ProgrammeEnergy consumption (KWh)Water consumption(litres)Programme duration(Minutes)White Cottons 95°1.9562
For the duration ofthe programmes,
please refer to the
display on the con‐ trol panel.
Cottons 60°1.1558Cotton  ECO 60°  1)1.0245Cottons 40°0.7558Synthetics 40°0.550Delicates 40°0.558Wool/ Handwash 30°0.2842
1) «Cotton Eco» at 60°C with a load of...

1.After removing all the packaging, careful‐
ly lay machine on it’s back to remove the
polystyrene base from the bottom.
2. Remove the power supply cable and the draining and inlet hose from the hose
holders on the rear of the appliance.
3. Unscrew the three bolts with the key sup‐
plied with the appliance.28InstallationDownloaded From WashingMachine-Manual.com Manual• 

4. Slide out the relevant plastic spacers.
5. Fill the smaller upper hole and the two large ones with the corresponding plastic
plug caps supplied in the bag containing
the instruction booklet.
Positioning and levelling Install the machine on a flat hard floor.
Make sure that air circulation around the machine
is not impeded by carpets, rugs etc.
Before placing it on small tiles, apply a rubber
coating.
Never try to correct any unevenness in the floor
by putting pieces of wood, cardboard or similar...

Carefully level by screwing the adjustable feet in or out. Never place cardboard, wood or
similar materials under the machine to compensate for any unevenness in the floor.
Water inlet This appliance must be connected to a cold water supply.
1. Connect the hose to a tap with a 3/4”
thread. Always use the hose supplied with
the appliance.
Do not use the hose from your previ‐
ous machine to connect to the water
supply.
2. The other end of the inlet hose which connects to the machine can be turned as
showed...