AEG Lavamat 86950 A User Manual

ProblemPossible cause/Solution
The door will not open:
The programme is still running.
• Wait the end of washing cycle.
There is water in the drum.
• Select drain or spin programme to empty out
the water.
For opening the door refer to display mes-
sage.
The machine vibrates or is noisy:
The transit bolts and packing have not been re-
moved.
• Check the correct installation of the appli-
ance.
The support feet have not been adjusted
• Check the correct levelling of the appliance.
The laundry is not evenly...

If you are unable to identify or solve the problem,
contact our service centre. Before telephoning,
make a note of the model, serial number and pur-
chase date of your machine: the Service Centre
will require this information.
Technical data
DimensionsWidth
Height
Depth
Depth (Overall dimensions)60 cm
85 cm
60 cm
63 cm
Electrical connection
Voltage - Overall power - FuseInformation on the electrical connection is given on the rating
plate, on the inner edge of the appliance door.
Water supply...

The consumption data shown on this chart is to be considered purely indicative, as it may
vary depending on the quantity and type of laundry, on the inlet water temperature and
on the ambient temperature.
Installation instructions
Installation
Unpacking
All transit bolts and packing must be removed before using the appliance.
You are advised to keep all transit devices so that they can be refitted if the machine ever
has to be transported again.
1. After removing all the packaging, careful-
ly lay...

3. Unscrew the three bolts with the key sup-
plied with the machine.
4. Slide out the relevant plastic spacers.
5. Open the porthole, take out the inlet hose
from the drum and remove the polystyr-
ene block fitted on the door seal.
34Installation
 

6. Fill the smaller upper hole and the two
large ones with the corresponding plastic
plug caps supplied in the bag containing
the instruction booklet.
7. Connect the water inlet hose as described
under the paragraph «Water inlet».
Positioning and levelling
Install the machine on a flat hard floor.
Make sure that air circulation around the machine
is not impeded by carpets, rugs etc.
Before placing it on small tiles, apply a rubber
coating.
Never try to correct any unevenness in the floor
by putting...

1. Open the porthole and extract the inlet
hose.
2. Connect the hose with the angled con-
nection to the machine.
Do not place the inlet hose downwards.
Angle the hose to the left or right de-
pending on the position of your water tap.
3. Set the hose correctly by loosening the
ring nut. After positioning the inlet hose,
be sure to tighten the ring nut again to
prevent leaks.
4. Connect the hose to a tap with a 3/4”
thread. Always use the hose supplied with
the appliance.
The inlet hose must not be...

Water-stop device
The inlet hose is provided with a water stop device,
which protects against damage caused by water
leaks in the hose which could develop due to nat-
ural ageing of the hose. This fault is shown by a
red sector in the window «A» . Should this occur,
turn the water tap off and refer to your Service
Centre to replace the hose.
Water drainage
The end of the drain hose can be positioned in three ways:
1.
Hooked over the edge of a sink using the plastic hose guide supplied with the
machine....

The drain hose may be extended to a maximum of 4 metres. An additional drain hose and
joining piece is available from your local Service Centre.
Electrical connection
Information on the electrical connection is given on the rating plate on the inner edge of
the appliance door.
Check that your domestic electrical installation can take the maximum load required, also
taking into account any other appliances in use.
WARNING!
Connect the machine to an earthed socket.
WARNING!
The manufacturer does not accept...

Packaging materials
The materials marked with the symbol  are recyclable.
>PEPSPP

www.electrolux.com
132946460 - 00 - 072010