AEG Lavamat 86850 Instruction Booklet

							41Consumption value
The consumption data shown on this chart is to be considered purely indicative,
as it may vary depending on the quantity and type of laundry, on the inlet water
temperature and on the ambient temperature.
(*) «Economy 60°C» with a load of 7 kg is the reference programme for the data
entered in the energy label, in compliance with EEC 92/75 standards.
Consumption value
Programme Water consumption
(lltres)Energy consumption
(KWh)Programme duration
(Minutes)
White Cottons 95°622.1
For the duration of the
programmes, please refer to
the display on the control
panel.
Cottons60°581.35
(*)Cotton ECO 60°451.19
Cottons 40°580.75
Synthetics 60°540.9
Delicates 40°530.55
Wool/ Handwash 40°620.4
132966571.qxd  21/01/2008  16.14  Pagina  41
 
						

							42Installation
Installation
Unpacking
All transit bolts and packing must be removed before using the appliance.
You are advised to keep all transit devices so that they can be refitted if the
machine ever has to be transported again.
1.After removing all the packaging, carefully
lay machine on it’s back to remove the
polystyrene base from the bottom.
2.Remove the power supply cable and the draining hose
from the hose holders on the rear of the appliance.
3.
With a suitable spanner unscrew and remove the central
rear bolt A.
	


	

	

132966571.qxd  21/01/2008  16.14  Pagina  42
 
						

							43Installation
4.Unscrew and remove the two large rear bolts B
and the six smaller bolts C.
5.Remove the bracket Dand tighten up the six
smaller bolts C. Slide out the relevant plastic
spacerE.
6.Open the porthole, take out the inlet hose from the
drum and remove the polystyrene block fitted on the
door seal.
7.Fill the smaller upper hole and the two large ones
with the corresponding plastic plug caps supplied in
the bag containing the instruction booklet.
8.Connect the water inlet hose as described under the
paragraph «Water inlet».
All the different plug caps are supplied with the
appliance in the plastic bag containing the instruction
booklet.




	




	


	


	

132966571.qxd  21/01/2008  16.14  Pagina  43
 
						

							44
Positioning and levelling
Install the machine on a flat hard floor.
Make sure that air circulation around the machine is
not impeded by carpets, rugs etc.
Before placing it on small tiles, apply a rubber
coating.
Never try to correct any unevenness in the floor by
putting pieces of wood, cardboard or similar
materials under the machine.
If it is impossible to avoid positioning the machine next to a gas cooker or coal-
burning stove, an insulating panel covered with aluminium foil on the side facing
the cooker or stove, must be inserted between the two appliances.
The machine must not be installed in rooms where the temperature can drop
below 0.
The water inlet hose and the drain hose must not be kinked.
Please ensure that when the appliance is installed, it is easily accessible for the
engineer in the event of a breakdown.
Carefully level by screwing the adjustable feet in or out. Never place cardboard,
wood or similar materials under the machine to compensate for any unevenness
in the floor.
Automatic foot:The rear foot on the left-hand side of your washing machine
is built as a shock absorbing foot, which is why the appliance gives in the back
left-hand corner if put under load. The automatic foot guarantees that the
appliance does not move even at high spin speeds. Basically the automatic foot
does not need to be set.
Water inlet
An inlet hose is supplied and can be found inside the machine drum.
Do not use the hose from your previous machine to connect to the
water supply.
This appliance must be connected to a cold water supply.
1.Open the porthole and extract the inlet hose.
2.Connect the hose with the angled connection to the machine.
Installation
	

132966571.qxd  21/01/2008  16.14  Pagina  44
 
						

							45
Do not place the inlet hose downwards. Angle
the hose to the left or right depending on the
position of your water tap.
3. Set the hose correctly by loosening the ring nut. 
After positioning the inlet hose, be sure to tighten
the ring nut again to prevent leaks.
4. Connect the hose to a tap with a 3/4” thread.
Always use the hose supplied with the appliance. 
Installation should comply with local water authority
and building regulations requirements. A minimum
water pressure of 0.05 MPa is required for safe
operation of the appliance.
If you cannot make the cold water connection direct
from the rising mains, you may be able to operate the
appliance from your cold water storage system. There
should be a minimum distance of between the appli-
ance’s inlet and the bottom of the water storage tank.
The inlet hose must not be lengthened. If it is too short and you do not wish to
move the tap, you will have to purchase a new, longer hose specially designed for
this type of use.
Water-stop device
The inlet hose is provided with a water stop device,
which protects against damage caused by water leaks in
the hose which could develop due to natural ageing of
the hose. This fault is shown by a red sector in the
window “A”. Should this occur, turn the water tap off
and refer to your Service Centre to replace the hose.
Water drainage
This appliance is designed to be permanently plumbed
into your homes drainage system using one of the
following methods.
1. Into a drainage standpipe.
Firstly form a hook in the end of the drain hose using
the “U” piece” supplied.
Installation 


	







132966571.qxd  21/01/2008  16.14  Pagina  45
 
						

							Place the drain hose into your
standpipe, which should have an
internal diameter of approximately
38mm thus ensuring there is an air
break between the drain hose and
standpipe.
When discharging into a standpipe
ensure that the top of the standpipe is
no more than 90 cm (35.4) and no less
than 60 cm (23.6) above floor level.
The drain hose may be extended to a
maximum of 4 metres. An additional
drain hose and joining piece is available
from your local Service Force Centre.
The joining piece must have an internal
diameter of 18 mm.
If your drain hose looks like this (see the relevant
pcture) you do not require the “U” piece”. Just push
the hose firmly into the standpipe.
2. Onto a sink outlet spigot.
If the outlet spigot has not been used before, remove
any blanking plug that may be in place.
Push the drain hose onto the spigot and secure with a
clip if required, ensure a loop is formed in the drain
hose (see diagram) to prevent waste from the sink
entering the washing machine.
The drain hose may be extended to a maximum of 4
metres. An additional drain hose and joining piece is
available from your local Service Force Centre. The
joining piece must have an internal diameter of 18 mm.
46Installation 
	

	








 
! 
132966571.qxd  21/01/2008  16.14  Pagina  46
 
						

							If you intend the drain hose from the machine to
empty into a sink, make sure that the sink is empty and
the plug hole is not blocked. Use the plastic “U -Piece”
supplied.
In the interest of the environment
Washing machines and dishwashers
should be connected to the FOUL
drainage system, the water will then
be taken to a sewage works for treat-
ment before being discharged safely
into a river.
It is essential that these appliances are
not connected to the surface water
drainage system as this water is dis-
charged directly into a river or stream
and may cause pollution.
If you require any further advice please
contact your local water authority.
Electrical connection
WARNING: THIS APPLIANCE MUST
BE EARTHED.
The manufacturer does not accept any responsibility for damage or
injury through failure to comply with the above safety precaution.
If the plug that is fitted to your appliance is not suitable for your socket outlet, it
must be cut off and the appropriate plug fitted.
Remove the fuse from the cut off plug.
The cut off plug should then be disposed of to prevent the hazard of shocks in case
it should be plugged into a 13 Amp socket in another part of your home.
47Installation 


	


	
 	

	
!	#$$!
$
	%
	

&$
	
$


 	

& 

	
!	#$$!
$
	
132966571.qxd  21/01/2008  16.14  Pagina  47
 
						

							Important
The wires in the mains lead are coloured in accor-
dance with the following code:
Green and Yellow - Earth
Blue - Neutral
Brown - Live
If you fit your own plug, the colours of the wires in the mains lead of your appli-
ance may not correspond with the markings identifying the terminals in your plug,
proceed as follows:
Connect the green and yellow (earth) wire to the terminal in the plug which is
marked with the letter «E» or the earth symbol  or coloured green and yellow.
Connect the blue (neutral) wire to the terminal in the plug which is marked with
the letter «N» or coloured black.
Connect the brown (live) wire to the terminal in the plug which is marked with the
letter «L» or coloured red.
The plug moulded on to the lead incorporates a fuse. For replacement, use a 13
Amp BS1363/Afuse. Only ASTA or BSI approved fuses should be used.
The plug must not be used if the fuse cover/carrier is lost. The cover/carrier is indi-
cated by the coloured insert at the base of the plug.
A replacement cover/carrier must be obtained from your local AEG/ELECTROLUX
Service Centre.
The power supply cable must be easily accessible after installing the
machine.
Should the appliance power supply cable need to be replaced, this MUST
be carried out by a Service Centre. 
Permanent connection
In the case of a permanent connection it is necessary that you install a double pole
switch between the appliance and the electricity supply (mains), with a minimum
gap of 3 mm between the switch contacts and of a type suitable for the required
load in compliance with the current electrical regulations.
The switch must not break the yellow and green earth cable at any point.
This operation must be performed by a qualified electrician.
48Installation
	

() $

 


() 
	
132966571.qxd  21/01/2008  16.14  Pagina  48
 
						

							49Environment concerns
Enviroment concerns
Packaging materials
The materials marked with the symbol  are recyclable.
>PEPSPP
						

							Standard guarantee conditions 
We, AEG-Electrolux , undertake that if within 12 months of the date of the pur-
chase this AEG-Electrolux appliance or any part thereof is proved to be defective
by reason only of faulty workmanship or materials, we will, at our option repair or
replace the same FREE OF CHARGE for labour, materials or carriage on condition
that: 
 The appliance has been correctly installed and used only on the electricity
supply stated on the rating plate. 
 The appliance has been used for normal domestic purposes only, and in
accordance with the manufacturers instructions. 
 The appliance has not been serviced, maintained, repaired, taken apart or
tampered with by any person not authorised by us. 
 Electrolux Service Force Centre must undertake all service work under this
guarantee 
 Any appliance or defective part replaced shall become the Companys
property. 
 This guarantee is in addition to your statutory and other legal rights. 
Exclusions
 Damage or calls resulting from transportation, improper use or neglect, the
replacement of any light bulbs or removable parts of glass or plastic. 
 Costs incurred for calls to put right an appliance which is improperly installed
or calls to appliances outside the United Kingdom. 
 Appliances found to be in use within a commercial environment, plus those
which are subject to rental agreements. 
 Products of Electrolux manufacturer that are not marketed by Electrolux 
Service and Spare Parts 
In the event of your appliance requiring service, or if you wish to purchase spare
parts, please contact your local Service Force Centre by telephoning 
0870 5 929 929 
Your telephone call will be automatically routed to the Service Force Centre cov-
ering your postcode area. 
50Guarantee/Customer Service
132966571.qxd  21/01/2008  16.14  Pagina  50