AEG Lavamat 84950 Instruction Booklet

41Something not working
The display shows the alarm code:
«Anti-flooding system has been
activated. Please check
inlet/drain pipe connections.»Anti-flooding system has activated.
 Disconnect the appliance and contact the
Service Force Centre 
The drum light doesn’t work:Please contact your local Service Centre.
Problem Possible cause/Solution
If you are unable to identify or solve the problem,
contact our service centre. Before telephoning,
make a note of the model, serial number and
purchase date of...

42Technical data
Technical Data
Dimensions
Width
Height
Depth
(door included)60 cm
85 cm
63 cm
Electrical connection
Voltage - Overall power -
FuseInformation on the electrical connection is given on the
rating plate on the inner edge of the appliance door
Water supply pressureMinimum
Maximum0,05 MPa
0,80MPa
Maximum Load
Cottons
Synthetics, Delicates
Jeans
Duvets, Wool Plus (handwash)
Outdoor sports
Easy iron plus
Lingerie and Silk
Quick Intensive8,0kg
4,0kg
4,0kg
2,0kg
3.0kg
2,0kg
1,0kg
5,0kg
Spin...

43Consumption value
The consumption data shown on this chart is to be considered purely indicative,
as it may vary depending on the quantity and type of laundry, on the inlet water
temperature and on the ambient temperature. It refers to the highest
temperature for each wash programme.
(*) «Economy 60°C» with a load of 8 kg is the reference programme for the data
entered in the energy label, in compliance with EEC 92/75 standards.
Drain--
Spin--
Wool Plus 40°630,5
Lingerie 40°600,45
Silk 30°520,3
Outdoor...

44Installation
Installation
Unpacking
All transit bolts and packing must be removed before using the appliance.
You are advised to keep all transit devices so that they can be refitted if the
machine ever has to be transported again.
1.After removing all the packaging, carefully lay
machine on it’s back to remove the
polystyrene base from the bottom.
2.Remove the power supply cable and the draining hose
from the hose holders on the rear of the appliance.
3.
With a suitable spanner unscrew and remove the...

45Installation
4.Unscrew and remove the two large rear bolts B
and the six smaller bolts C.
5.Remove the bracket Dand tighten up the six
smaller bolts C. Slide out the relevant plastic
spacerE.
6.Open the porthole, take out the inlet hose from the
drum and remove the polystyrene block fitted with the
adhesive tape on the door seal.
7.Fill the smaller upper hole and the two large ones with
the corresponding plastic plug caps supplied in the bag
containing the instruction booklet.
8.Connect the water inlet...

Positioning and levelling
Install the machine on a flat hard floor.
Make sure that air circulation around the machine is
not impeded by carpets, rugs etc.
Before placing it on small tiles, apply a rubber
coating.
Never try to correct any unevenness in the floor by
putting pieces of wood, cardboard or similar
materials under the machine.
If it is impossible to avoid positioning the machine next to a gas cooker or coal-
burning stove, an insulating panel covered with aluminium foil on the side facing
the...

Do not place the inlet hose downwards. Angle
the hose to the left or right depending on the
position of your water tap.
3.Set the hose correctly by loosening the ring nut. 
After positioning the inlet hose, be sure to tighten
the ring nut again to prevent leaks.
4.Connect the hose to a tap with a 3/4” thread.
Always use the hose supplied with the appliance. 
The inlet hose must not be lengthened. If it is too short and you do not wish
to move the tap, you will have to purchase a new, longer hose...

When discharging into a standpipe
ensure that the top of the standpipe is
no more than 90 cm (35.4) and no less
than 60 cm (23.6) above floor level.
The drain hose may be extended to a
maximum of 4 metres. An additional
drain hose and joining piece is available
from your local Service Force Centre.
The joining piece must have an internal
diameter of 18 mm.
If your drain hose looks like this (see the relevant
pcture) you do not require the “U” piece”. Just push
the hose firmly into the standpipe.
2. Onto...

In the interest of the environment
Washing machines and dishwashers
should be connected to the FOUL
drainage system, the water will then
be taken to a sewage works for treat-
ment before being discharged safely
into a river.
It is essential that these appliances are
not connected to the surface water
drainage system as this water is dis-
charged directly into a river or stream
and may cause pollution.
If you require any further advice please
contact your local water authority.
Electrical connection...

If you fit your own plug, the colours of the wires in the mains lead of your appli-
ance may not correspond with the markings identifying the terminals in your plug,
proceed as follows:
Connect the green and yellow (earth) wire to the terminal in the plug which is
marked with the letter «E» or the earth symbol  or coloured green and yellow.
Connect the blue (neutral) wire to the terminal in the plug which is marked with
the letter «N» or coloured black.
Connect the brown (live) wire to the terminal in...