AEG Lavamat 75470 Fl User Manual

L 75470 FL
L 75670 FLENWASHING MACHINE USER MANUAL
 

CONTENTS
4 SAFETY INFORMATION
5 TECHNICAL INFORMATION
6 PRODUCT DESCRIPTION
6 ACCESSORIES
7 CONTROL PANEL
11 PROGRAMMES
14 CONSUMPTION VALUES
15 BEFORE FIRST USE
15 USING THE APPLIANCE
15 LOADING THE LAUNDRY
15 FILLING THE DETERGENT AND ADDITIVES
17 SETTING AND STARTING A PROGRAMME
18 AT THE END OF THE PROGRAMME
19 HELPFUL HINTS AND TIPS
21 CARE AND CLEANING
26 TROUBLESHOOTING
29 INSTALLATION
ENVIRONMENT CONCERNS
Recycle the materials with the symbol  . Put the packaging in applicable containers to...

FOR PERFECT RESULTS
Thank you for choosing this AEG product. We have created it to give you
impeccable performance for many years, with innovative technologies that help
make life simpler – features you might not find on ordinary appliances. Please spend
a few minutes reading to get the very best from it.
ACCESSORIES AND CONSUMABLES
In the AEG webshop, you’ll find everything you need to keep all your AEG
appliances looking spotless and working perfectly. Along with a wide range of
accessories designed...

 SAFETY INFORMATION
Before the installation and use, read this
manual carefully:
• For your safety and the safety of your
property
• To help the environment
• For the correct operation of the appli-
ance.
Always keep these instructions with the
appliance also if you move or give it to a
different person.
The manufacturer is not responsible if an
incorrect installation and use causes dam-
age.
CHILDREN AND VULNERABLE
PERSON SAFETY
• Do not let persons, children included,
with reduced physical sensory,...

• Do not install and connect a damaged
appliance.
• Make sure to remove all packaging and
transport bolts.
• Make sure that the mains plug is dis-
connected from the mains socket dur-
ing installation.
• Only a qualified person must do the
electrical installation, the plumbing and
the installation of the appliance. This to
prevent the risks of structural damage
or injury.
• Do not install or use the appliance
where the temperature is less than 0 °C.
• When you install the appliance on a
carpet floor,...

1) 
Connect the water inlet hose to a water tap with a 3/4'' thread.
PRODUCT DESCRIPTION
12389
5
6
7
4
10
11
12
1Worktop
2Detergent dispenser
3Control panel
4Door handle
5Rating plate
6Drain pump
7Feet for the appliance level
8Water drain hose
9Water inlet valve
10Mains cable
11Transit bolts
12Feet for the appliance level
ACCESSORIES
123
45
1Spanner
To remove the transit bolts.
2Plastic caps
To close the holes on the rear side of
the cabinet after the removal of the
transit bolts.
3Anti-flood...

CONTROL PANEL
20 Min. - 3 kg
ECOSUPER ECO
45678910
123
1On/Off button (Auto Off)
2Programme knob 
3Display 
4Start Pause button
5Delay start button
6Time save button
7Extra rinse button
8Stain button
9Spin reduction button
10Temperature button
ON OFF BUTTON 1
Press this button to activate or deactivate
the appliance. A tune sounds when the
appliance is activated.
The AUTO Stand-by function automatical-
ly deactivates the appliance to decrease
the energy consumption when:
• You do not use the appliance...

DISPLAY 3
ABCD
The display shows:
A• The maximum temperature of the programme.
B• The default spin speed of the programme.
•
'No Spin'
1) and 'Rinse Hold' symbols.
C•
The display symbols.2)
SymbolsDescription
Washing phase
Rinse phases
Spin phase
Child lock
You cannot open the appliance door when the symbol is on.
You can open the door only when the symbol goes off.
If the programme is completed but the symbol stays on:
• There is water in the drum.
• The 'Rinse Hold' function is...

D• The programme time
When the programme starts, the time decreases with steps of 1 minute.
• The delay start
When you press the delay start button, the display shows the delay start
time.
•Alarm codes
If the appliance has a malfunction, the display shows alarm codes. Refer
to 'Troubleshooting' chapter.
•Err
The display shows this message for some seconds if:
– You set a function that is not applicable for the programme.
– You change the programme while it operates.
The indicator of the...

TEMPERATURE BUTTON 10
Press button 10 to change the default
temperature.
- -= cold water
ACOUSTIC SIGNALS
FUNCTION
You can hear the acoustic signals when:
• You activate the appliance.
• You deactivate the appliance.
• You press the buttons.
• The programme is completed.
• The appliance has a malfunction.
To deactivate/activate the acoustic sig-
nals, press button 
8 and button 7 at
the same time for 6 seconds.
If you deactivate the acoustic sig-
nals, they continue operate only
when you press the...