AEG Lavamat 74760 Information Manual

Operating Instructions
41
Child Safety Feature
If the child safety feature is set, 
the filling door can no longer be 
closed and no washing program 
can be started. 
Setting the child safety feature
0 Use a coin to turn the rotary knob 
on the inside of the filling door 
clockwise as far as it will go.
1 Warning! The rotary knob must 
not be in a vertical position after 
adjustment, otherwise the child 
safety feature is not active. The ro-
tary knob must project as shown in 
the diagram
Cancelling the...

Installation and connection instructions
42
Installation and connection instructions
Installation Safety Precautions
Do not tilt the washing machine onto its front or onto its right side 
(viewed from the front). Electronic components can get wet.
Check the washing machine for transport damages. A damaged unit 
must never be put into operation under any circumstances. In the 
event of damage, please contact your supplier.
Ensure that all parts of the transport safeguard are removed and that 
the unit...

Installation and connection instructions
43
Installation of the appliance
3 Washing machines with curved panels are not suitable for installing 
under units.
Transporting the appliance
Do not place the washing machine on its front or on its right side 
(viewed from the front). Otherwise, electrical components can get 
wet.
Never transport the unit without the transport safeguard. Do not re-
move the transport safeguard until the appliance is at the installation 
location. Transporting the unit without...

Installation and connection instructions
44
2.Pull both hose holders off the ap-
pliance with a strong pull.
3 The special spanner (A) and the
caps (B) (2 each) and (C) (1 each)
are supplied with it.
3.Remove the screw D, including 
the compression spring with the 
special spanner A.
4.Cover the hole with the cap C.
Important! When fitting the 
plastic caps, press until they snap 
into the rear panel securely.
5.Remove the two screws (E) with 
the special spanner (A).
6.Remove the 4 screws (F).
7.Remove...

Installation and connection instructions
45
Prepare the installation place
The installation surface must be clean and dry, free of floor polish 
residues and other greasy coatings so that the unit does not slip 
away. Do not use lubricants as a sliding aid.
Installation on a high-veil carpet or floor tiles with soft sponge backs 
is not recommended because the standing safety of the appliance is 
then no longer ensured.
By installation surfaces with small-format tiles, lay a conventional 
rubber mat...

Installation and connection instructions
46
Compensate for floor unevenness
Floor unevenness can be compensated for and the height can be cor-
rected with the four adjustable screw feet. The height can be adjusted 
in the range +10 .. -5mm.
To adjust the feet use the special spanner supplied for removing the 
transport braces.
0 1.Slide the special key firmly onto 
the hexagon head of the threa-
ded foot as far as it will go.
2.Adjust the screw feet so that the 
unit is horizontal and stable. The 
unit...

Installation and connection instructions
47
Electrical connection
Details of the mains voltage, current 
type and required fuses can be 
found on the rating plate. The ra-
ting plate is located at the top 
above the filling door.
For permanent electrical connection 
within the electrical circuit, provi-
sions must be made which allow for electrical disconnection of the ap-
pliance from the mains with a contact opening of at least 3 mm at all 
poles. Suitable devices include circuit breakers, fuses...

Installation and connection instructions
48
Water inflow
A pressure hose 1.5 m in length is supplied.
If a longer inflow hose is required, only a VDE-approved, complete set 
of hoses with fitted hose screw connections offered by our Customer 
Service is permissible.
–Hose sets in lengths of 2.2 m, 3.5 m and 5 m are available for washing 
machines without Aqua-Control. 
–Hose sets in lengths of 2.0 m, 2.9 m and 3.9 m are available for wash-
ing machines with Aqua-Control.
Caution! Never cut into pieces in...

Installation and connection instructions
49
Water drain
The drainage hose can either be connected to a siphon or hung in a 
wash basin or discharge basin or a bath tub.
Only original hoses may be used for extensions (max. 3m laid on the 
floor and then up to 80cm high). Customer Service stocks drainage 
hoses in lengths of 2.7 and 4m.
Important! It is essential to lay the drainage hose without kinks.
Water drain-off inside a siphon
The grommet on the hose end fits all 
standard siphon types. 
0 Secure...

50
Technical data
Dimensions  
(dimensions in mm) Adjustment possibility Approx. +10 / -5mm
Filling quantity (program-dependent) max. 6kg
Area of use Domestic
Drum speed, spinning See rating plate
Water pressure 1-10 bar (= 10 - 100 N/cm
2 
= 0.1 - 1.0 Mpa)