AEG Lavamat 62800 Information Manual

11
Running a wash cycle
Opening the door/loading washing
1.Open the door: pull the handle on the door.
When the appliance is switched on, the DOOR and START/PAUSE indica-
tors show whether the door can be opened: 
2.Separate washing and load it loose-
ly. Mix large and small items.
Important: Do not get any washing 
caught between the door and the 
rubber seal.  
3.Firmly push the door shut. Door 
catch must audibly click shut.
Adding detergent  / conditioner
Important: Only use detergents/conditioners...

12
Water softener should be used from water hardness range 2 (=medi-
um). The amount of detergent used can then always be that as for 
hardness range 1 (=soft). Your local water company will provide you 
with information about water hardness in your area.
1.Pull out the detergent drawer as far as it will go.
2.Add the detergent/conditioner.
3.Push the detergent drawer in fully.
Washing powder/tablets for the main wash cycle 
If you are using water softener and require the right compartment for...

13
Switching on the appliance/selecting a programme
Set the programme and tempera-
ture using the programme selector. 
3The appliance is switched on by se-
lecting a programme.
–The programme progress display 
shows the programme steps that 
the selected programme will car-
ry out.
–The estimated programme dura-
tion (in minutes) appears in the 
multi-display.
Changing the spin speed/selecting rinse hold
The washing machine suggests the 
maximum permitted spin speed 
suitable for the selected pro-...

14
Selecting additional programmes
If required, press additional pro-
gramme button(s). The correspond-
ing indicator will illuminate.  
3If “Err” flashes in the multi-display, 
the selected additional programme 
cannot be used together with the 
wash programme set.
RINSE +
Two additional rinse cycles are carried out for the programmes ENERGY 
SAVING, COTTONS/LINEN, EASY-CARES and DELICATES (for example in 
cases of over-sensitive skin).
TIME SAVER
Shortened wash programme for lightly soiled items.
PRE...

15
Starting a programme
1.Check that the tap is turned on.
2.Press the START / PAUSE button. The programme is started.
3If after pressing the START/PAUSE button E40  flashes in the multi-dis-
play, the END indicator flashes 4 times and at the same time an acous-
tic signal sounds 4 times, the door has not been correctly shut. Push the 
door firmly closed and press the START/PAUSE button again.
Programme sequence
The programme progress display shows the programme step that is 
currently being carried...

16
End of the wash cycle / removing the washing
At the end of the programme, END lights up on the programme 
progress display. The door can be opened as soon as the DOOR indicator 
is lit green.
1.Open the loading door and remove the washing.
2.Turn the programme knob to OFF.
3.Close the water valve.
4.After washing, pull out the detergent drawer a little to enable it to dry 
out. Keep the loading door very slightly open so that the washing ma-
chine can air.
If RINSE HOLD has been selected: 
After the...

17
Child safety device
If the child safety device has been activated, the door can no longer be 
shut.
Activating the child safety device:
Use a coin to turn the knob (on the 
inside of the door) in a clockwise di-
rection as far as it will go.
1Warning! The knob must not be de-
pressed after being set, otherwise 
the child safety device is not acti-
vated. The knob must stand proud 
as shown in the illustration. 
Deactivating the child safety device: 
Turn the knob in an anti-clockwise direction as far...

18
Cleaning and maintenance
Important! Do not use furniture care products or aggressive cleaners to 
clean the appliance. 
Wipe control panel and body with a damp cloth.
Cleaning procedure
If you plan to wash mainly at low temperature, you should run a hot 
programme from time to time. This will reduce any deposits and clean 
the appliance from the inside.
Detergent dispenser drawer
The detergent dispenser drawer should be cleaned regularly.
1.Remove the detergent dispenser drawer by pulling it firmly....

19
Door and rubber collar
Regularly check whether deposits or foreign bodies are present in the 
folds of the rubber collar or on the inside of the glass door. 
Clean the glass in the door and the rubber collar regularly.
What to do if...
Remedying small faults yourself
If during use of the appliance one of the following error codes is shown 
in the multi-display:
–E10 (Problems with the water inflow),
–E20 (Problems with the water outflow),
–E40 (door open),
please consult the following table.
After the...

20
E10 appears.
The END indicator is 
flashing once, and si-
multaneously an acous-
tic signal is sounding 
once.
(Problems with the wa-
ter inflow.)The tap is shut off.Turn on the tap.
The filter in the inlet hose 
screw connection is blocked.Turn off the tap. Unscrew the 
hose, remove the filter and 
clean it.
The tap is blocked by limes-
cale or faulty.Check the tap and have it re-
paired, if necessary.
The washing machine 
vibrates when operating 
or is not stable.
The transit packaging has 
not been...