Home > AEG > Washing Machine > AEG Lavamat 62640 User Manual

AEG Lavamat 62640 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual AEG Lavamat 62640 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 513 AEG manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							11Use
    Personalization
    Acoustic signals
    The machine is provided of an acoustic device, which
    sounds in the following cases:
    ●at the end of the cycle
    ●in the event of operating problems
    By pressing the Prewashand Stain buttons simultaneously for about 6 seconds,
    the acoustic signal is deactivated (except for the events of operating problems).
    By pressing these 2 buttons again, the acoustic signal is reactivated.
    Child safety lock 
    This device permits you to leave the appliance unsupervised without having the
    worry that children might be injured by or cause damage to the appliance.
    This function remains able also when the washing machine is not working.
    There are two different ways to set this option:
    ●before pressing the Start/Pause: it will
    be impossible to start the machine.
    ●after pressing the Start/Pauseit will
    be impossible to change any other
    programme or option.
    To enable (disable) this option press
    simoultaneously for about 6 seconds
    Stainand Time savingbuttons until the
    icon  appears (disappears) on (from) the
    display.
    192998381 gb.qxd  9/8/2008  10:12 AM  Page 11
     
    						
    							12Use
    Daily Use
    Load the laundry
    1.Open the door by carefully pulling the door
    handle outwards. Place the laundry in the drum,
    one item at a time, shaking them out as much
    as possible.
    2.Close firmly the door. You must hear a click
    during closing.
    Attention!Do not embed the laundry
    between the door and the rubber joint.
    Measure out the detergent and the fabric
    softener
    Your new appliance was designed to reduce
    water, energy and detergent consumption.
    1.Pull out the dispenser drawer until it
    stops. Measure out the amount of
    detergent required, pour it into the main
    wash compartment and, if you wish
    to carry out the prewashphase, pour it
    into the compartment marked . If you
    wish to carry out to perform the stain
    function, pour it into the compartment
    .
    2. If required, pour fabric softener into the
    compartment marked  (the amount
    used must not exceed the MAXmark in
    the drawer). Close the drawer gently.
    192998381 gb.qxd  9/8/2008  10:12 AM  Page 12
     
    						
    							Select the required programme
    You can choose the right programme for any type of laundry following the
    descriptions on the washing programme tables (see Washing Programmes).
    Turn the programme selector dial to the required programme. The programme
    selector determines the type of washing cycle (e.g. water level, drum movement,
    number of rinses) and the washing temperature according to the type of laundry.
    The Start/Pauselight starts to flash and the Display shows the duration of the
    selected programme.
    The selector dial is divided into following
    sections:
    ●Cottons
    ●Synthetics
    ●Delicates
    ●Wool, Silk and Handwash
    ●Special programme: Rinses, Drain, Spin
    ●Refresh
    ●Economy programme (ECO)
    The selector dial can be turned either clockwise or anticlockwise. Position 
    Oto Reset
    programme/Switching OFF of the machine.
    At the end of the programme the selector dial must be turned to position
    O, to switch the machine off.
    Attention!
    If you turn the programme selector dial to another programme when the machine
    is working, the yellow Start/Pausepilot light will flash 3 times and the message
    Erris displayed on the display to indicate a wrong selection. The machine will not
    perform the new selected programme.
    Select the spin speed  or the rinse hold option 
    Press the Spinbutton repeatedly to change the spin speed, if you want your
    laundry to be spun at a speed different from the one proposed by the washing
    machine. 
    The relevant light will light up.
    Maximum speed are:
    Lavamat 60640:
    ●1000 rpm for all type of fabrics.
    Lavamat 62640:
    ●1200 rpm for all type of fabrics.
    13Use
    
    
    	
    
    
    
    
    
    
    
    
      
    
    
    
    
    
    
    192998381 gb.qxd  9/8/2008  10:12 AM  Page 13
     
    						
    							Rinse Hold:by selecting this option the water of the last rinse is not emptied out
    to prevent the fabrics from creasing. When the programme has finished the display
    shows a 
    0flashing, the pilot lights Doorgoes on, the Start/Pauselight is off
    and the door is blocked to indicate that the water must be emptied out.
    To empty the water out:
    ●turn the programme selector dial to O
    ●select the Drainor Spinprogramme
    ●reduce the spin speed if needed, by means of the relevant button
    ●depress Start/Pausebutton
    ●when the programme has finished the display shows a 0flashing. The pilot
    lights Doorgoes off and the door can be opened.
    Programme option button
    Depending on the programme, different functions can be combined. These must
    be selected after choosing the desired programme and before depressing the
    Start/Pausebutton.
    When these buttons are pressed, the corresponding pilot lights come on. When
    they are pressed again, the pilot lights go out.
    If an incorrect option is selected, the integrated yellow pilot light of the
    Start/Pausebutton flashes for 3 times and the Errmessage appears on the
    display for some seconds.
    Important!
    For the compatibility among the washing programmes and the options see
    chapter Washing Porgrammes.
    Select the Prewash option 
    Select this option if you wish your laundry to be
    prewashed at 30°C before the main wash. The
    prewash ends with a short spin in programmes for
    cotton and synthetic fabrics, whereas in the
    programmes for delicate fabrics the water is only
    drained.
    The relevant light will light up.
    14Use
    192998381 gb.qxd  9/8/2008  10:12 AM  Page 14
     
    						
    							Select the Stain option 
    Select this option to treat heavily soiled or stained
    laundry with stain remover (extended main wash
    with time optimised stain action phase). The relevant
    light will light up.
    This option is notavailable with a temperature lower
    than 40°C.
    Attention!If you wish to perform a programme with the stain option, pour
    stain remover into compartment  .
    Select the Time Saving option 
    This option allows you to modify the washing time,
    automatically proposed by the washing machine.
    By pressing this button, the relative pilot light comes
    on and the washing duration will be reduced to wash
    daily soiled laundry.
    On the display will be visualized the decreased
    washing time. The maximum load is 6 kg for cottons
    and 2 kg for synthetics and delicates. 
    By pressing this button twice, the relative pilot light remains lit, the washing
    duration will be reduced to wash lightly soiled laundry or items that have been
    used or worn for a short time. On the display will be visualized the decreased
    washing time. The maximum load is 3 kg for cottons and 1,5 kg for synthetics
    and delicates.
    Display
    The display shows the following information:
    Duration of the selected programme
    After selecting a programme, the duration
    is displayed in hours and minutes (for
    example 
    2.05). The duration is calculated
    automatically on the basis of the
    maximum recommended load for each
    type of fabric.
    After the programme has started, the time remaining is updated every minute.
    15Use
    192998381 gb.qxd  9/8/2008  10:12 AM  Page 15
     
    						
    							Incorrect option selection
    If an option which is not compatible with
    the set wash programme is selected, the
    message Erris displayed for about 2
    seconds and the yellow Start/Pauselight
    start flashing.
    Alarm codes
    In the event of operating problems, some
    alarm codes can be displayed, for example
    E20(see paragraph «Something not
    working»).
    End of programme
    When the programme has finished a
    flashing zero is displayed, the  pilot
    light and the Start/Pauselight go out and
    the door can be opened.
    Select the Start/Pause 
    To start the selected programme, press the
    Start/Pausebutton; the corresponding red
    pilot light stops flashing.
    The washing pilot light washis on to
    indicate that the appliance starts operating.
    The door pilot light dooris on to
    indicate the door is locked.
    To interrupt a programme which is running, depress the Start/Pausebutton: the
    corresponding red pilot light starts to flash.
    To restart the programme from the point at which it was interrupted, pressthe
    Start/Pausebuttonagain.
    If an incorrect option is selected, the integrated yellow pilot light of the
    Start/Pausebutton flashes for 3 times the message Erris displayed for about 2
    seconds.
    16Use
    192998381 gb.qxd  9/8/2008  10:12 AM  Page 16
     
    						
    							17Use
    Programme progress display
    After having pressed the Start/Pausebutton, the wash pilot lights comes on.
    When the pilot light wash comes on
    this means that the machine is performing
    the washing cycle.
    The door pilot light indicates if the
    door can be opened:
    ●light on: the door cannot be opened.
    The appliance is running.
    ●light off: the door can be opened. The washing programme is finished.
    When the appliance is performing additional rinses the Extra Rinsepilot
    light comes on.
    Select an additional rinse 
    This appliance is designed for saving water.
    However, for people with a very delicate
    skin (allergic to detergents) it may be
    necessary to rinse the laundry using an
    extra quantity of water (extra rinse).
    Press simultaneously the Spin Speedand
    Prewashbuttons for some seconds: the
    Extra Rinsepilot light comes on in the
    programme progress display. This function stays permanently on. To remove it
    press the same buttons again until the Extra Rinselight goes off.
    Altering an option or a running programme
    It is possible to change any option before the programme carries it out. Before
    you make any change, you must pause the washing machine by pressing the
    Start/Pause button.
    Changing a running programme is possible only by resetting it. Turn the
    programme selector dial to Oand then to the new programme position. The
    washing water in the tub will be not emptied out. Start the new programme by
    depressing the Start/Pausebutton again.
    Interrupting a programme
    Depress the Start/Pausebutton to interrupt a programme which is running, the
    corresponding light starts to flash. Depress the button again to restart the
    programme.
    
    
    
    
    192998381 gb.qxd  9/8/2008  10:12 AM  Page 17
     
    						
    							Cancelling a programme
    Turn the selector dial to Oto cancel a programme which is running. Now you
    can select a new programme.
    Opening the door after the programme has started
    First set the machine to pause by pressing the Start/Pausebutton.
    The door can be opened.
    If the door remains locked, this means that the machine is already heating,
    that the water level is above the bottom edge of the door. In this case the door
    can not be opened.
    If you cannot open the door but you need to open it you have to switch the
    machine off by turning the selector dial to O. After about some minutes the
    door can be opened (pay attention to the water level and temperature!).
    At the end of the programme
    The machine stops automatically, the Start/Pauselight goes off and a flashing 0
    will appear on the display.
    If the Rinse Holdoption have been selected, the Doorpilot light
    illuminates, a flashing 
    0will appear on the display, the Start/Pauselight goes
    off and the door remains locked to indicate that the water must be emptied out
    before opening the door.
    To empty out the water please read the steps on the Rinse Hold option
    paragraph.
    Turn the programme selector dial to Oto switch the machine off. 
    Remove the laundry from the drum and carefully check that the drum is empty.
    If you do not intend to carry out another wash, close the water tap. Leave the
    door open to prevent the formation of mildew and unpleasant smells.
    18Use
    192998381 gb.qxd  9/8/2008  10:12 AM  Page 18
     
    						
    							* Stainoption can be selected only at the temperature of 40°C or higher.
    ** Time Savingoption cannot be selected with 40-60 MIX programme.
    19Washing programmes
    Washing programmes
    P
    Pr
    ro
    og
    gr
    ra
    am
    mm
    me
    e/
    /
    T Te
    em
    mp
    pe
    er
    ra
    at
    tu
    ur
    re
    eT
    Ty
    yp
    pe
    e 
     o
    of
    f 
     l
    la
    au
    un
    nd
    dr
    ry
    yO
    Op
    pt
    ti
    io
    on
    ns
    sD
    De
    es
    sc
    cr
    ri
    ip
    pt
    ti
    io
    on
    n 
     o
    of
    f
    p pr
    ro
    og
    gr
    ra
    am
    mm
    me
    e
    Cottons 
    95°-60°
    White cotton:e.g.
    sheets, tablecloths,
    household linen.Main wash from 95°C
    to 60°C
    3 rinses 
    Long spin
    Cottons 
    40°-30°
    40-60 MIXColoured cotton: work
    garments, sheets,
    household linen,
    underwear, towels.*
    **Main wash from 40°C to
    30°C 
    3 rinses 
    Long spin
    Synthetics
    Easy Iron 
    40°Synthetics to be gentle
    washed and spun.Main wash at 40°C
    4 rinses 
    Short spin
    Delicates
    40°-30°Delicate fabrics:for
    example curtains*Main wash from 40°C to
    30°C 
    3 rinses 
    Short spin
    Synthetics
    60°-50°-40°-30°
    Synthetic or mixed
    fabrics:
    underwear,
    coloured garments,
    non-shrink shirts,
    blouses.*Main wash from 60°C to
    30°C 
    3 rinses 
    Short spin
    Handwash
    Wool
    40°-30°- 
    Special programme for
    hand washing fabrics
    and specially tested
    programme for wool
    garments bearing the
    «Pure new wool, non-
    shrink, machine
    washable» label.
    Main wash from 40°C to
    (Cold) 
    3 rinses 
    Short spin
    192998381 gb.qxd  9/8/2008  10:13 AM  Page 19
     
    						
    							20Washing programmes
    Washing programmes
    P Pr
    ro
    og
    gr
    ra
    am
    mm
    me
    e/
    /
    T Te
    em
    mp
    pe
    er
    ra
    at
    tu
    ur
    re
    eT
    Ty
    yp
    pe
    e 
     o
    of
    f 
     l
    la
    au
    un
    nd
    dr
    ry
    yO
    Op
    pt
    ti
    io
    on
    ns
    sD
    De
    es
    sc
    cr
    ri
    ip
    pt
    ti
    io
    on
    n 
     o
    of
    f
    p pr
    ro
    og
    gr
    ra
    am
    mm
    me
    e
    Delicate
    rinses
    Separate rinse cycle for
    hand washed items.3 rinses 
    Long spin
    Drain
    For emptying out the last
    rinse water in
    programmes with the
    Rinse Hold option.
    Draining of water
    SpinSeparate spin for all type
    of fabric.Drain and long spin
    Refresh
    Quick wash for sport
    items, or cotton and
    synthetics items lightly
    soiled or worn once.Main wash at 30°C
    2 rinses 
    Short spin
    ECO
    White and coloured
    cotton economy,
    lightly-heavy soiled
    items, shirts, underwear.Main wash at 60°C
    2 rinses 
    Long spin
    Off/O
    Type of fabricMax. Load
    Cottons6 kg
    Synthethics and Delicates3 kg
    40° Easy Iron1,5 kg
    Wool and Handwash2 kg
    Refresh2 kg
    For cancelling the pro-
    gramme which is run-
    ning or to switch the
    machine off.
    192998381 gb.qxd  9/8/2008  10:13 AM  Page 20
     
    						
    All AEG manuals Comments (0)

    Related Manuals for AEG Lavamat 62640 User Manual