AEG Lavamat 60610 Information Manual

21
Carrying out an emergency drain
1Warning! Before emergency draining, switch off the washing machine 
and remove the mains plug from the socket.
Warning! The water that comes out of the emergency drain hose may 
be hot. There is a risk of scalding. Let the water cool before performing 
an emergency drain.
1.Open the plinth flap and remove it.
2.Take out the emergency drain hose. 
3.Place a shallow container under-
neath it. Then loosen the drain plug 
by turning it in an anti-clockwise 
direction and...

22
Drain pump
The drain pump is maintenance-free. It is only necessary to open the 
pump cover if there is a malfunction and water is no longer being 
pumped out, e. g. if the pump wheel is blocked. 
Please make sure before loading the washing that there are no foreign 
bodies in the pockets or caught between the washing. Paperclips, nails, 
etc. that may have got into the washing machine with the washing re-
main in the pump housing (foreign body trap that protects the pump 
wheel). 
1Warning! Before...

23
Disposal
2
Packaging material
The packaging materials are environmentally friendly and can be recy-
cled. The plastic components are identified by markings, e.g. >PEPS

24
Technical data
5
This appliance conforms with the following EU Directives:
–73/23/EEC dated 19.02.1973 Low Voltage Directive
–89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending 
Directive 92/31/EEC
–93/68/EEC dated 22.07.1993 CE Marking Directive
Consumption values
The consumption values were obtained under standardised conditions. 
They may vary when operating in domestic conditions. 
 
Height x Width x Depth850 x 598 x 603 mm
Depth when door is open980 mm
Height adjustmentapprox. +10/-5...

25
Installation and connection instructions
1Safety information for the installation
This washing machine cannot be built-in.
Before using for the first time, check the appliance for damage sus-
tained while it was being transported. Do not under any circumstanc-
es connect an appliance that is damaged. In the case of damage, 
please contact your supplier.
Before using for the first time, all parts of the transit packaging must 
be removed. Otherwise when spinning damage may be caused to the...

26
Installing the appliance
Transporting the appliance
1Warning! The washing machine is very heavy. Risk of injury. Be careful 
when lifting.
Do not lay the appliance on its front nor on its right side (as seen 
from the front). Electrical components may get wet.
Never transport the appliance without its transit packaging. Only re-
move the transit packaging when the appliance is in its place of in-
stallation. Transporting the appliance without its transit packaging 
can lead to damage to the...

27
3.Remove both plastic caps sideways. 
3Special spanner A and sealing caps B 
(2 off) and C (1 off) are supplied 
with the appliance.
4.Remove screw D with its compres-
sion spring using special spanner A.
5.Turn sealing cap C upside down as 
shown in the illustration. 
6.Seal hole using sealing cap C.
7.Unscrew and remove two screws E 
using special spanner A.
8.Unscrew and remove four screws F 
using special spanner A.
9.Remove transit bar G.
10.Screw in the four screws F again.
11 .Seal the two big...

28
The surface on which the appliance is to be installed must be clean 
and dry and free from coverings that move, so that the appliance 
does not slide.
If the location in which the appliance is to be installed is fitted with 
small-format tiles, put a rubber mat (available in the shops) under 
the appliance.
If the appliance is to stand on a 
plinth:  
In order for the appliance to be se-
cure on the plinth, fixing plates*) 
must be mounted, into which the 
appliance is inserted. 
If the appliance is...

29
Electrical connection
Details about the voltage, type of supply and the fuses required are to 
be found on the rating plate. The rating plate is next to the doorway.
Connecting to the water supply
Important! 
This appliance must not be connected to the hot water system.
When connecting it, use only new hose kits.
Only connect the appliance to the drinking water supply. Rain water 
or water for industrial use may only be used if it fulfils the require-
ments of DIN 1986 and DIN 1988.
Do not kink or...

30
Water inflow
A 1.50  m long pressure hose is supplied with the appliance. 
If a longer water inlet hose is required, only original hoses are to be 
used. The Customer Care Department stocks hose kits of different 
lengths.
3Sealing rings are either inserted in the plastic nuts of the threaded hose 
fitting or are included as spare parts . Do not use any other seals. 
Important! All threaded hose fit-
tings must only be tightened by 
hand. 
1.Connect the hose with the right-an-
gle connector to the...