AEG Lavamat 46210 User Manual

							Technical specifications21
Technical specifications
DIMENSIONSHeight
Width
Depth850 mm
400 mm
600 mm
LINE VOLTAGE / FREQUENCY
POWER CONSUMPTION230 V / 50 Hz
2300 W
WATER PRESSURE
Connection to water supplyMinimum
Maximum0,05 MPa (0,5 bar)
0,8 MPa (8 bar)
Type 20x27
This appliance conforms to the CEE 89-336 directive concerning the limiting of
radio-electric interference and the 2006/95/CE directive concerning electrical
safety.
 
						

							Care and cleaning22
Care and cleaning
Unplug the appliance before cleaning.
Descaling the appliance
It is not generally necessary to remove limescale from the appliance if the de-
tergent product is properly dosed.
If it becomes necessary to remove limescale, use a commercially available
special non-corrosive product specifically designed for washing machines.
Follow the dosing instructions and observe the intervals between uses indi-
cated on the packaging.
The exterior
Use warm soapy water to clean the exterior of the appliance. Never use alco-
hol, solvents or similar products.
Dispenser box
From time to time you should clean the detergent dispenser to remove any
residues from detergent products and so avoid any operating anomalies.
2. Separate the two parts of the
detergent dispenser. 1. Lift out the detergent dispen-
ser.
 
						

							Care and cleaning23
3. Clean the two parts of the detergent dispenser under running water.
4. Re-assemble the two parts of
the detergent dispenser.5. Reposition the detergent dis-
penser.
 
						

							Care and cleaning24
Drainage filter
Clean the filter located at the base of the appliance regularly :
1. Open the door, with the aid of
a screwdriver, for example.2. Place a bowl underneath it.
Turn the plug anti-clockwise until
it is vertical and can release the
residual water.
3. Unscrew the plug completely
and remove it.4. Clean it carefully under running
water.
 
						

							Care and cleaning25
Water inlet filters
5. Put it back in. 6. Screw in the plug.
7. Close the door again.
Unscrew the ends of the water inlet pipe and clean the filters.
 
						

							Operating problems26
Operating problems
Numerous checks were carried out on your appliance before it left the
factory. However, should you notice a malfunction, please refer to the
sections below before contacting the after-sales service.
ProblemsCauses
The washing machine doesn’t
start or doesn’t fill :
installation isn’t working,
and the drum shutters aren’t
closed firmly,

selected,

has been cut off,



The appliance fills but empties
straight away :xed too low (see installation
section).
The washing machine doesn’t
rinse or doesn’t empty :


washing is unevenly distributed in the drum,

“Rinse hold” option have been selected,

You have found water around
the washing machine :used foam to overflow,


 been put back in place,

Wash is unsatisfactory :



The appliance vibrates, is noisy :
section),




 
						

							Operating problems27
the wash cycle is much too
long:
pply has been cut off,


 system has been activated
(too much detergent) and the washing machine has
begun draining the foam,

extra phase has been added to distribute washing more
evenly in the drum.
The washing machine stops
during a wash cycle :


The lid doesn’t open at the end
of the cycle :* light is not lit,


cycle*.
The E40 error code appears in
the display** and the START/
PAUSE pushbutton flashes in
yellow
*** :

The E20 error code appears in
the display** and the START/
PAUSE pushbutton flashes in
yellow*** :


section).


The E10 error code appears in
the display** and the START/
PAUSE pushbutton flashes in
yellow*** :
has been cut off.
The EF0 error code appears in
the display** and the START/
PAUSE pushbutton flashes in
yellow*** :
system has been activated,
please proceed as follows :
- close the water inlet tap,
- empty the appliance for 2 minutes before unplugging,
- call the after-sales service.
The drainage pump runs
constantly, even when the
appliance is inactive :system has been activated,
please proceed as follows :
- close the water inlet tap,
- empty the appliance for 2 minutes before unplugging,
- call the after-sales service.
ProblemsCauses
 
						

							Operating problems28
Softener runs directly into the
drum when filling the dispenser
box :
* Depending on model.
** On some models, the audible signals can sound.
*** After solving any problems, press the START/PAUSE pushbutton to restart the interrupted programme.
ProblemsCauses
 
						

							Warnings29
Warnings
 This appliance is heavy. Take care when moving it.
 The appliance must have the transit bolts removed before use. If all
protective transit devices are not removed, this could cause damage to the
appliance or to neighbouring cabinets or furniture. The appliance must be
unplugged from the electricity supply when the transit bolts are being
removed.
 Connection to the water supply must be carried out by a qualified plumber.
 The appliance must be equipped with an earthed power plug which
conforms to regulations.
 If your domestic electrical circuit needs adapting to allow the appliance to
be plugged in, use a qualified electrician.
 Before connecting your appliance to the power supply, carefully read the
instructions in the chapter entitled “Electrical connection”.
 Ensure that, after installation, the power cable is not trapped under the
appliance.
 If the appliance is installed on carpeted floor, ensure that the carpet does
not obstruct any ventilation ducts located at the base of the appliance.
 Replacing the power cable should only be carried out by the After Sales
Service.
 The manufacturer cannot be held responsible for any damage resulting
from incorrect installation.
 
						

							Installation30
Installation
Remove all protective packaging for transit before using for the first time.
Keep in case needed for future transit : Transporting a non-secured appliance
may damage internal components and cause leakages and malfunctions. The
appliance can also be damaged through physical contact.
Unpacking
1. Tilt the appliance backwards. 2. Make it do a quarter turn on
one of the corners to remove the
transport base.
4. Remove the plastic film. 3. Open the lid of the appliance
and remove the red block.