AEG Lavamat 14710 Vit Instruction Booklet

							
41
Something not working?
Spinning starts late or the
machine does not spin
The unbalance detection If the laundry is not evenly
device that prevents distributed inside the drum
excessive vibration during at the beginning of the
spinning has cut in. spin cycle, the machinedetects this and tries to
redistribute it more evenly
by means of a few drum
rotations.
Only when the laundry is
more evenly distributed
will the spin cycle be
performed, at a lower speed,
if the laundry is not evenly
distributed.
If, after about 6 minutes,
the laundry is still tangled,
the machine will not spin.
Therefore, if the laundry is
still wet at the end of the
cycle, it is advisable to
redistribute it manually
inside the drum and to
select the spin programme
again.
ProblemPossible causeSolution
The machine will not dry or
the laundry is not dry
enough
The water tap is not open Open the water tap.
(E10).
The drying time has not Select the drying time.
been selected.
An appropriate drying pro- Select the appropriate
gramme or drying time  drying time suitable for the
have not been chosen. required degree of drying,
according to the type of
fabric (cottons or easy-cares).
There is too much laundry Reduce the load.
inside the appliance.

132984531.qxd  28/11/2005  16.32  Pagina  41
 
						

							
Unsatisfactory washing results
If the laundry looks grey and lime scale is found in the drum 
 Too little detergent has been used.
 An unsuitable detergent has been used.
 Stubborn stains have not been treated prior to washing.
 The programme/temperature has not been correctly selected.
If grey stains remain on the laundry
 Laundry stained with ointments, grease or oil has been washed with aninsufficient amount of detergent.
 The temperature selected for the wash programme was too low.
 Fabric softener - especially the concentrated type - has come into direct contact with the laundry. Wash these stains immediately and pour fabric
softener carefully.
Foam is still visible even after the last rinse
 Modern detergents often produce foam, even in the last rinse. However the laundry has been completely rinsed.
White residue is left on the laundry
 This is due to insoluble components in modern detergents and is therefore not the result of insufficient rinsing. Shake or brush the laundry. In future,
it may be better to turn garments inside out before washing them. Check
the choice of detergent; try using liquid detergents.
42
Something not working?

132984531.qxd  28/11/2005  16.32  Pagina  42
 
						

							
Technical data
Height x Width x Depth 82x60x54.5 cm
Depth with door opened  95 cm
Height adjustment  ± 13 mm approx.
Load (depending on programme)  5 kg max.
Use domestic
Drum speed during washing max. 55 rpm
Drum speed during spinning  1200/900/700/500 rpm (L12710VIT)1400/900/700/500 rpm (L14710VIT)
Water pressure 0.05 - 0.8 MPa
This appliance complies with the following EC directives:
- 73/23/EEC of 19.2.1973 “Low voltage directive”, including directive 93 / 68 / EEC
- 89/336/EEC of 3.5.1989 “Electromagnetic Compatibility Directive”.

43

132984531.qxd  28/11/2005  16.32  Pagina  43
 
						

							
Service &Spare Parts
If after carrying out the necessary checks there is still a fault with your appliance
please contact your local AEG/ELECTROLUX Service Force Centre.
In guarantee customers should ensure that the suggested checks in the
“Troubleshooting” section have been made as the engineer will make a
charge if the fault is not a mechanical or electrical breakdown.
Please note that proof of purchase is required for in-guarantee service calls.
Service  &Spare Parts
If you require a service engineer or wish to purchase spare parts, contact your
local AEG/ELECTROLUX Service Force Centre, by telephoning:
08705 929 929
Help us to help you
Please determine your type of enquiry before telephoning. When you con-
tact us we need to know:
1. Your name, address and post code.
2. Your telephone number.
3. Clear and concise details of the fault. - What is the fault?
- When does the fault occur?
- Does the multi-display issue an error-message ( Eand a number)?
4. The model, production number and production identification number.
5. Date of purchase.
This information can be found on the rating plate, so you have these num-
bers to hand we recommed you write them below.
Prod. No.  . . . . . . . . . . . . . . . . . . . . . . . . . .
Ser. No.   . . . . . . . . . . . . . . . . . . . . . . . . . . .
44

\b	
\b\f


 \b \b	 
		\f	\
 \b 
! 
\f

132984531.qxd  28/11/2005  16.32  Pagina  44
 
						

							
45

Service &Spare Parts 
Customer care
For general enquiries regarding your AEG/ELECTROLUX appliance, or further
information on AEG/ELECTROLUX products please contact our Customer Care
Department at the address below or visit our website at www.aeg-electrolux.co.uk  
Customer Care Department
AEG/ELECTROLUX Major Appliances
Addington Way
Luton
Bedfordshire LU4 9QQ
Tel: 08705 350350*
*Calls to this number may be recorded for training purposes.
132984531.qxd  28/11/2005  16.32  Pagina  45
 
						

							
Guarantee Conditions
AEG/ELECTROLUX offer the following guarantee to the first purchaser of this
appliance.
1. The guarantee is valid for 12 months commencing when the appliance ishanded over to the first retail purchaser, which must be verified by pur-
chase invoice or similar documentation.
The guarantee does not cover commercial use.
2. The guarantee covers all parts or components which fail due to faulty workmanship or faulty materials. The guarantee does not cover appliances
where defects or poor performance are due to misuse, accidental damage,
neglect, faulty installation, unauthorised modification or attempted repair,
commercial use or failure to observe requirements and recommendations
set out in the instruction book.
This guarantee does not cover such parts as light bulbs, removable glass-
ware or plastic, dust bags or filters.
3. Should guarantee repairs be necessary the purchaser must inform the near- est customer service office (AEG/ELECTROLUX’s service or authorised
agent). AEG/ELECTROLUX reserves the right to stipulate the place of the
repair (i. e. the customer’s home, place of installation or AEG/ELECTROLUX
workshop).
4. The guarantee or free replacement includes both labour and materials.
5. Repairs carried out under guarantee do not extend the guarantee period for the appliance. Parts removed during guarantee repairs become the
property of AEG/ELECTROLUX.
6. The purchaser’s statutory rights are not affected by this guarantee.
46

132984531.qxd  28/11/2005  16.32  Pagina  46
 
						

							
European Guarantee
If you should move to another country within Europe then your guarantee
moves with you to your new home subject to the following qualifications:\
- The guarantee starts from the date you first  purchased your product.
- The guarantee is for the same period and to the same extent for labourand parts as exist in the new country of use for this brand or range of
products.
- This guarantee relates to you and cannot be transferred to another user.
- Your new home is within the European Community (EC) or European Free Trade Area.
- The product is installed and used in accordance with our instructions and is only used domestically, i.e. a normal household.
- The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care Centre, listed
below, to give them details of your new home. They will then ensure that the
local Service Organisation is aware of your move and able to look after you
and your appliance.
France Senlis +33 (0) 44 62 29 29
Germany Nürnberg +49 (0) 911 323 2600
Italy Pordenone +39 (0) 1678 47053
Sweden Stockholm +46 (0) 8 738 7910
UK Luton +44 (0)8705 350350
47
Guarantee Conditions

132984531.qxd  28/11/2005  16.32  Pagina  47
 
						

							
Instructions for installation and electrical con-
nection
Safety instructions for the installer
 This appliance is heavy, care should be taken when moving it.
 When unpacking the appliance, check that it is not damaged. If in doubt,\
do not use it and contact the retailer.
 All internal packing must be removed before using the appliance. Serious damage may be caused to the machine or adjacent furniture if the protec-
tive transit devices are not removed or are not completely removed. Refer
to the relevant paragraph.
 Any electrical work required to install this appliance must be carried out by a qualified electrician or competent person.
 Any plumbing work required to install this appliance must be carried out by a qualified plumber or competent person.
 After having installed the machine, check that it is not standing on its\
 elec- trical supply cable.
 If the appliance is placed on a carpeted floor, ensure that air can circulate freely between the adjustable feet and the floor.
 The installation should comply with local water authority and building r\
eg- ulations requirements.
 Should the appliance power supply cable need to be replaced, this should be carried out by our Service Force Centre.

48

132984531.qxd  28/11/2005  16.32  Pagina  48
 
						

							
Dimensions of the appliance
Front view and side view
Rear view
49





\b	
\f

\f \f
\f
\f \f
\f
\f
\f
	\f
	
\f\f
\f\f\f\f
\f\f



  



 \b

  
   
\b	 \b

!

  

 
\b	
\f\f
\b



	! 


	

\f

\f \f
	#	!!

 !

   

\b	

\b
 




\b
 \b\f	



132984531.qxd  28/11/2005  16.32  Pagina  49
 
						

							
Installation
Unpacking
All transit bolts and packing must be removed before using the appliance.Using the supplied spanner, unscrew
and remove the rear right-hand bolt and lay
the machine on its back, taking care not to
squash the hoses. This can be avoided by plac-
ing one of the corner packing pieces between
the machine and the floor.
Remove the polystyrene base and take off the
bottom panel by
unscrewing the
central screw.
Carefully slide out
the right poly-
thene bag.
Repeat the opera-
tion for the left
and central poly-
thene bags.
Re-fit the bottom
panel using the 4
screws supplied
with the door
hinges (in the plas-
tic bag) and the
previously removed
screw.

50



132984531.qxd  28/11/2005  16.32  Pagina  50