AEG L 60270 Fl Manual

To clean the drain pump:
1.Open the drain pump door.
2.Put a container below the recess of
the drain pump to collect the water
that flows out.
3.Press the two levers and pull forward
the drainage duct to let the water
flow out.
4.When the container is full of water,
put the drainage duct back again and
empty the container. Do steps 3 and
4 again and again until no more wa-
ter flows out from the drain pump.
12
5.Pull back the drainage duct and turn
the filter to remove it.
6.Remove fluff and objects from...

21
8.Clean the filter under the water tap
and put it back in the pump into the
special guides.
9.Make sure that you tighten correctly
the filter to prevent leakages.
10.Close the drain pump door.
THE INLET HOSE FILTER AND
THE VALVE FILTER
It could be necessary to clean the filters
when:
• The appliance does not fill with water.
• The appliance fills with the water for a
long time.•
The indicator of button 
4 flashes and
the display shows the related alarm. Re-
fer to 'Troubleshooting'.
WARNING!...

45°
20°
6.Install again the inlet hose. Make sure
that the couplings are tight to pre-
vent leakages.
7.Open the water tap.
EMERGENCY DRAIN
Because of a malfunction, the appliance
cannot drain the water.
If this occurs, do steps (1) through (6) of
'To clean the drain pump'.
If necessary, clean the pump.
Put the drainage duct back and close the
drain pump flap.
When you drain the water with the emer-
gency drain procedure, you must activate
again the drain system:
1.Put 2 litres of water in the...

TROUBLESHOOTING
The start of the appliance does not occur
or it stops during operation.
First try to find a solution to the problem
(refer to the table). If not, contact the serv-
ice centre.
With some problems, the acoustic
signals operate and the display shows
an alarm code:
•
 - The appliance does not fill with
water.•
 - The appliance does not drain
the water.
•
 - The appliance door is open or
not closed correctly.
WARNING!
Deactivate the appliance before
you do the checks.
ProblemPossible...

ProblemPossible causePossible solution
The spin phase
does not operate.The spin phase is off.Set the spin programme.
 The filter of the drain
pump is blocked.Clean the filter of the drain
pump. Refer to 'Care and clean-
ing'.
 Balance problems with
the laundry load.Adjust manually the items in the
tub and start the spin phase
again.
The programme
does not start.The mains plug is not
connected in the mains
socket.Put in the mains plug.
 Blow out fuse in the
household fuse box.Replace the fuse....

ProblemPossible causePossible solution
 You did not remove the
stubborn stains before
you wash the laundry.Use special products to remove
the stubborn stains.
 Incorrect temperature
was set.Make sure that you set the cor-
rect temperature.
 Too much laundry load.Decrease the laundry load.
After the check, activate the appliance.
The programme continues from the point
of interruption.
If the problem occurs again, contact the
service centre.
If the display shows other alarm codes,
contact the service...

INSTALLATION
SPECIAL ACCESSORIES FOR
INSTALLATION
FIXING PLATE KIT (405517114)
Available from your authorized dealer.If you install the appliance on a plinth, se-
cure the appliance in the fixing plates.
Follow the instructions supplied with the
kit.
UNPACKING
1.Use the gloves. Remove the external
film. If necessary, use a cutter.
2.Remove the cardboard top.
3.Remove the polystyrene packaging
materials.
4.Remove the internal film.
ENGLISH27 

5.Open the door and remove all the
items from the drum.
6.Put one of the polystyrene packaging
elements on the floor behind the ap-
pliance. Carefully put down the appli-
ance with the rear side on it. Make
sure not to damage the hoses.
1
2
7.Remove the polystyrene protection
from the bottom.
8.Pull up the appliance in vertical posi-
tion.
9.Remove the power supply cable and
the drain hose from the hose holders.
28www.aeg.com 

10.Remove the three bolts. Use the key
supplied with the appliance.
11.Pull out the plastic spacers.
12.Put the plastic caps in the holes. You
can find these caps in the user man-
ual bag.
– We recommend that you keep
the packaging and the transit
bolts for when you move the
appliance.
– If the appliance is delivered in
the winter months when there
are minus temperatures. Store it
at room temperature for 24
hours before using for the first
time.
ENGLISH29 

POSITIONING AND LEVELLING
x4
• Install the appliance on a flat hard floor.
• Make sure that carpets do not stop the
air circulation below the appliance.
• Make sure that the appliance does not
touch the wall or other units
• Loosen or tighten the feet to adjust the
level. A correct adjustment of the appli-
ance level prevents the vibration, noise
and the movement of the appliance
when in operation.
• The appliance must be level and stable.
CAUTION!
Do not put cardboard, wood or
equivalent materials below...