AEG Integrated refrigerator SKS61840S1 User Manual

							ProblemPossible causeSolution
 The door is not closed
correctly.Refer to "Closing the
door".
 The door has been
opened too frequently.Do not keep the door
open longer than necessa-
ry.
 The food temperature is
too high.Let the food temperature
decrease to room temper-
ature before storage.
 The room temperature is
too high.Decrease the room tem-
perature.
Water flows on the
rear plate of the re-
frigerator.During the automatic de-
frosting process, frost de-
frosts on the rear plate.This is correct.
Water flows into the
refrigerator.The water outlet is clog-
ged.Clean the water outlet.
 Products prevent that wa-
ter flows into the water
collector.Make sure that products
do not touch the rear
plate.
The temperature in
the appliance is too
low/high.The temperature regula-
tor is not set correctly.Set a higher/lower temper-
ature.
If your appliance is still not working
properly after making the above checks,
please contact the After Sales Centre.
6.1 Replacing the control unit
The appliance is equipped with a long-
life LED interior light.
Only service is allowed to replace the
control unit. Contact your Service Cen-
ter.
6.2 Closing the door
1.Clean the door gaskets.
2.If necessary, adjust the door. Refer
to "Installation".
3.If necessary, replace the defective
door gaskets. Contact the Service
Center.
7. INSTALLATION
7.1 Positioning
WARNING!
If you are discarding an old appli-
ance that has a lock or catch on
the door, you must ensure that it
is made unusable to prevent
young children being trapped in-
side.
The appliance shall have the
plug accessible after installation.Install this appliance at a location where
the ambient temperature corresponds to
the climate class indicated on the rating
plate of the appliance:
Cli-
mate
classAmbient temperature
SN+10°C to + 32°C
N+16°C to + 32°C
ST+16°C to + 38°C
ENGLISH11 
						

							Cli-
mate
classAmbient temperature
T+16°C to + 43°C
7.2 Electrical Connection
CAUTION!
Any electrical work required to
install this appliance should be
carried out by a qualified electri-
cian or competent person.
WARNING!
This appliance must be earthed.
The manufacturer declines any li-
ability should these safety meas-
ures not be observed.
12
3
4
5
The wires in the mains lead are
coloured in accordance with the
following code:
1Green and Yellow: Earth
3Brown: Live
5Blue: Neutral
As the colours of the wires in the mains
lead of this appliance may not corre-
spond with the coloured markings iden-
tifying the terminals in your plug, pro-
ceed as follows:
1.Connect the wire coloured green
and yellow to the terminal marked
either with the letter “E“ or by the
earth symbol 
 or coloured green
and yellow.
2.Connect the wire coloured blue to
the terminal either marked with the
letter “N“ or coloured black.
3.Connect the wire coloured brown to
the terminal either marked with the
“L“ or coloured red.
4.Check that no cut, or stray strands of
wire is present and the cord clamp
4 is secure over the outer sheath.
5.Make sure the electricity supply volt-
age is the same as that indicated on
the appliance rating plate.
6.Switch on the appliance.
The appliance is supplied with a 13 amp
plug fitted 
2 . In the event of having to
change the fuse in the plug supplied, a
13 amp ASTA approved (BS 1362) fuse
must be used.
WARNING!
A cut off plug inserted into a 13
amp socket is a serious safety
(shock) hazard. Ensure that it is
disposed of safely.
7.3 Door reversibility
The door of the appliance opens to the
right. If you want to open the door to the
left, follow these steps before you install
the appliance:
12www.aeg.com 
						

							1.Loosen and remove the upper pin.
2.Remove the door.
3.Remove the spacer.
4.With a key, loosen the lower pin.
On the opposite side:
1.Tighten the lower pin.
2.Install the spacer.
3.Install the door.
4.Tighten the upper pin.
7.4 Ventilation requirements
5 cmmin.
200 cm2
min.
200 cm2
The airflow behind the appliance must
be sufficient.
7.5 Installing the appliance
CAUTION!
Make sure that the mains cable
can move freely.Do the following steps:
ENGLISH13 
						

							x
x
If necessary cut the adhesive sealing strip
and then apply it to the appliance as
shown in figure.
Ø 2.5 mm
13 mm
1
32
Drill the appliance using a Ø 2.5 mm drill
(10 mm max. penetration).
Fix the square fitting to the appliance.
1 2
Install the appliance in the niche.
Push the appliance in the direction of the
arrow (1) until the upper gap cover stops
against the kitchen furniture.
Push the appliance in the direction of the
arrow (2) against the cupboard on the op-
posite side of the hinge.
14www.aeg.com 
						

							44mm
4mm
Adjust the appliance in the niche.
Make sure that the distance between the
appliance and the cupboard front-edge is
44 mm.
The lower hinge cover (in the accessories
bag) makes sure that the distance be-
tween the appliance and the kitchen fur-
niture is correct.
Make sure that the clearance between
the appliance and the cupboard is 4 mm.
Open the door. Put the lower hinge cover
in position.
I
I
Attach the appliance to the niche with 4
screws.
Remove the correct part from the hinge
cover (E). Make sure to remove the part
DX, in the case of right hinge, SX in op-
posite case.
ENGLISH15 
						

							EE
B DC
Attach the covers (C, D) to the lugs and
the hinge holes.
Install the vent grille (B).
Attach the hinge covers (E) to the hinge.
Disconnect the parts (Ha), (Hb), (Hc) and
(Hd).
21 mm ~50 mm~50 mm
90
o
90o
90o
Install the part (Ha) on the inner side of
the kitchen furniture.
16www.aeg.com 
						

							Ha
Hc
Push the part (Hc) on the part (Ha).
Ha
Hb
8 mm
Open the appliance door and the kitchen
furniture door at an angle of 90°.
Insert the small square (Hb) into guide
(Ha).
Put together the appliance door and the
furniture door and mark the holes.
Remove the small squares and drill holes
with ø 2 mm at 8 mm from the outer edge
of the door.
Place the small square on the guide again
and fix it with the screws supplied.
Hb
Align the kitchen furniture door and the
appliance door by adjusting the part (Hb).
ENGLISH17 
						

							Hb
Hd
Press the part (Hd) on the part (Hb).
Do a final check to make sure that:
• All screws are tightened.• The sealing strip is attached tightly to
the cabinet.
• The door opens and closes correctly.
7.6 Reversibility of the freezer door
12
12
180
18www.aeg.com 
						

							 
8. NOISES
There are some sounds during normal
running (compressor, refrigerant circula-
tion).
BRRR!HISSS!
CLICK!
BLUBB!
CRACK!
SSSRR
R!
OK
CLICK!CLICK!SSSRRR!SSSRRR!
ENGLISH19 
						

							BRRR!BRRR!HISSS!HISSS!
BLUBB!BLUBB!CRACK!CRACK!
9. TECHNICAL DATA
   
Dimension of the recess  
 Height1780 mm
 Width560 mm
 Depth550 mm
Rising Time 20 h
Voltage 230-240 V
Frequency 50 Hz
The technical information are situated in
the rating plate on the internal left side
of the appliance and in the energy label.
20www.aeg.com