AEG Integrated fridge freezer SCT81900S0 User Manual

							• do not exceed the storage period in-
dicated by the food manufacturer.
5. CARE AND CLEANING
CAUTION!
Unplug the appliance before car-
rying out any maintenance oper-
ation.
This appliance contains hydrocar-
bons in its cooling unit; mainte-
nance and recharging must
therefore only be carried out by
authorized technicians.
5.1 Periodic cleaning
The equipment has to be cleaned regu-
larly:
• clean the inside and accessories with
lukewarm water and some neutral
soap.
• regularly check the door seals and
wipe clean to ensure they are clean
and free from debris.
• rinse and dry thoroughly.
Do not pull, move or damage
any pipes and/or cables inside
the cabinet.
Never use detergents, abrasive
powders, highly perfumed clean-
ing products or wax polishes to
clean the interior as this will dam-
age the surface and leave a
strong odour.Clean the condenser (black grill) and the
compressor at the back of the appliance
with a brush. This operation will improve
the performance of the appliance and
save electricity consumption.
Take care of not to damage the
cooling system.
Many proprietary kitchen surface clean-
ers contain chemicals that can attack/
damage the plastics used in this appli-
ance. For this reason it is recommended
that the outer casing of this appliance is
only cleaned with warm water with a little
washing-up liquid added.
After cleaning, reconnect the equipment
to the mains supply.
ENGLISH11 
						

							5.2 Defrosting of the refrigerator
Frost is automatically eliminated from
the evaporator of the refrigerator com-
partment every time the motor compres-
sor stops, during normal use. The de-
frost water drains out through a trough
into a special container at the back of
the appliance, over the motor compres-
sor, where it evaporates.
Periodically clean the defrost water drain
hole in the middle of the refrigerator
compartment channel to prevent the wa-
ter overflowing and dripping onto the
food inside. Use the special cleaner pro-
vided, which you will find already inser-
ted into the drain hole.
5.3 Defrosting of the freezer
The freezer compartment of this model,
on the other hand, is a "no frost" type.
This means that there is no buildup of
frost when it is in operation, neither on
the internal walls nor on the foods.
The absence of frost is due to the con-
tinuous circulation of cold air inside the
compartment, driven by an automatically
controlled fan.
5.4 Periods of non-operation
When the appliance is not in use for
long periods, take the following precau-
tions:•disconnect the appliance from elec-
tricity supply
• remove all food
• defrost (if foreseen) and clean the ap-
pliance and all accessories
• leave the door/doors ajar to prevent
unpleasant smells.
If the cabinet will be kept on, ask some-
body to check it once in a while to pre-
vent the food inside from spoiling in
case of a power failure.
6. WHAT TO DO IF…
WARNING!
Before troubleshooting, discon-
nect the mains plug from the
mains socket.
Only a qualified electrician or
competent person must do the
troubleshooting that is not in this
manual.There are some sounds during
normal use (compressor, refriger-
ant circulation).
ProblemPossible causeSolution
The appliance is
noisyThe appliance is not sup-
ported properlyCheck if the appliance
stands stable (all the four
feet should be on the
floor)
12www.aeg.com 
						

							ProblemPossible causeSolution
The appliance does
not operate. The
lamp does not oper-
ate.The appliance is switched
off.Switch on the appliance.
 The mains plug is not
connected to the mains
socket correctly.Connect the mains plug to
the mains socket correctly.
 The appliance has no
power. There is no volt-
age in the mains socket.Connect a different electri-
cal appliance to the mains
socket.
Contact a qualified electri-
cian.
The lamp does not
work.The lamp is in stand-by.Close and open the door.
 The lamp is defective.Refer to "Replacing the
lamp".
The Pilot light flash-
es.The appliance is not
working properly.Contact a qualified electri-
cian.
The buzzer sounds.
The Alarm light
flashing.The temperature in the
freezer is too high.Refer to "High Tempera-
ture Alarm".
The compressor op-
erates continually.The temperature is not
set correctly.Set a higher temperature.
 The door is not closed
correctly.Refer to "Closing the
door".
 The door has been
opened too frequently.Do not keep the door
open longer than necessa-
ry.
 The product temperature
is too high.Let the product tempera-
ture decrease to room
temperature before stor-
age.
 The room temperature is
too high.Decrease the room tem-
perature.
The compressor
does not start imme-
diately after press-
ing the FROSTMAT-
IC or COOLMATIC
button, or after
changing the tem-
perature.This is normal, no error
has occurred.The compressor starts af-
ter a period of time.
Water flows on the
rear plate of the re-
frigerator.During the automatic de-
frosting process, frost de-
frosts on the rear plate.This is correct.
ENGLISH13 
						

							ProblemPossible causeSolution
Water flows into the
refrigerator.The water outlet is clog-
ged.Clean the water outlet.
 Products prevent that wa-
ter flows into the water
collector.Make sure that products
do not touch the rear
plate.
Temperature cannot
be set .FROSTMATIC or COOL-
MATIC functions switched
on.Switch off FROSTMATIC or
COOLMATIC manually, or
wait to set the temperature
until the function has reset
automatically. Refer to
"FROSTMATIC or COOL-
MATIC function"..
The temperature in
the appliance is too
low/high.The temperature regula-
tor is not set correctly.Set a higher/lower temper-
ature.
 The door is not closed
correctly.Refer to "Closing the
door".
 The product temperature
is too high.Let the product tempera-
ture decrease to room
temperature before stor-
age.
 Many products are stored
at the same time.Store less products at the
same time.
The temperature in
the refrigerator is
too high.There is no cold air circu-
lation in the appliance.Make sure that there is
cold air circulation in the
appliance.
The temperature in
the freezer is too
high.Products are too near to
each other.Store products so that
there is cold air circulation.
6.1 Replacing the lamp
The appliance is equipped with a long-
life LED interior light.
Only service is allowed to replace the
lighting device. Contact your Service
Center.
6.2 Closing the door
1.Clean the door gaskets.
2.If necessary, adjust the door. Refer
to "Installation".
3.If necessary, replace the defective
door gaskets. Contact the Service
Center.
14www.aeg.com 
						

							7. INSTALLATION
WARNING!
Read the "Safety Information"
carefully for your safety and cor-
rect operation of the appliance
before installing the appliance.
7.1 Positioning
Install this appliance at a location where
the ambient temperature corresponds to
the climate class indicated on the rating
plate of the appliance:
Cli-
mate
classAmbient temperature
SN+10°C to + 32°C
N+16°C to + 32°C
ST+16°C to + 38°C
T+16°C to + 43°C
7.2 Electrical Connection
CAUTION!
Any electrical work required to
install this appliance should be
carried out by a qualified electri-
cian or competent person.
WARNING!
This appliance must be earthed.
The manufacturer declines any li-
ability should these safety meas-
ures not be observed.
12
3
4
5
The wires in the mains lead are
coloured in accordance with the
following code:
1Green and Yellow: Earth
3Brown: Live
5Blue: Neutral
As the colours of the wires in the mains
lead of this appliance may not corre-
spond with the coloured markings iden-
tifying the terminals in your plug, pro-
ceed as follows:
1.Connect the wire coloured green
and yellow to the terminal marked
either with the letter “E“ or by the
earth symbol 
 or coloured green
and yellow.
2.Connect the wire coloured blue to
the terminal either marked with the
letter “N“ or coloured black.
3.Connect the wire coloured brown to
the terminal either marked with the
“L“ or coloured red.
4.Check that no cut, or stray strands of
wire is present and the cord clamp
4 is secure over the outer sheath.
5.Make sure the electricity supply volt-
age is the same as that indicated on
the appliance rating plate.
ENGLISH15 
						

							6.Switch on the appliance.
The appliance is supplied with a 13 amp
plug fitted 
2 . In the event of having to
change the fuse in the plug supplied, a13 amp ASTA approved (BS 1362) fuse
must be used.WARNING!
A cut off plug inserted into a 13
amp socket is a serious safety
(shock) hazard. Ensure that it is
disposed of safely.
7.3 Door reversibility
The door of the appliance opens to the
right. If you want to open the door to the
left, do these steps before you install the
appliance:
• Loosen the upper pin and remove the
spacer.
• Remove the upper pin and the upper
door.
B C
C
• Unscrew the pins (B) and spacers (C).
• Remove the lower door.
• Loosen the lower pin.
On the opposite side:
• Install the lower pin.
• Install the lower door.
• Refit the pins (B) and the spacers (C)
on the middle hinge on the opposite
side.
• Install the upper door.
• Tighten the spacer and the upper pin.
16www.aeg.com 
						

							7.4 Ventilation requirements
5 cmmin.
200 cm2
min.
200 cm2
The airflow behind the appliance must
be sufficient.
7.5 Installing the appliance
CAUTION!
Make sure that the mains cable
can move freely.Do these steps.
x
x
If necessary cut the adhesive sealing strip
and then apply it to the appliance as
shown in figure.
A1 A
Drill the hinge cover A, as shown in figure.
Apply the covers A and A1 (in the acces-
sories bag) in to the middle hinge.
ENGLISH17 
						

							1 2
Install the appliance in the niche.
Push the appliance in the direction of the
arrow (1) until the upper gap cover stops
against the kitchen furniture.
Push the appliance in the direction of the
arrow (2) against the cupboard on the op-
posite side of the hinge.
4 mm
44 mm
Adjust the appliance in the niche.
Make sure that the distance between the
appliance and the cupboard front-edge is
44 mm.
The lower hinge cover (in the accessories
bag) makes sure that the distance be-
tween the appliance and the kitchen furni-
ture is correct.
Make sure that the clearance between the
appliance and the cupboard is 4 mm.
Open the door. Put the lower hinge cover
in position.
I
I
Attach the appliance to the niche with 4
screws.
18www.aeg.com 
						

							Remove the correct part from the hinge
cover (E). Make sure to remove the part
DX, in the case of right hinge, SX in oppo-
site case.
EE
B DC
Attach the covers (C, D) to the lugs and
the hinge holes.
Install the vent grille (B).
Attach the hinge covers (E) to the hinge.
H
H
If the appliance must connect laterally to
the kitchen furniture door:
1.Slacken the screws in fixing brackets
(H).
2.Move the brackets (H).
3.Retighten the screws.
ENGLISH19 
						

							Disconnect the parts (Ha), (Hb), (Hc) and
(Hd).
ca. 50 mm
ca. 50 mm21 mm 90°       
90°       
21 mmInstall the part (Ha) on the inner side of
the kitchen furniture.
Ha
Hc
Push the part (Hc) on the part (Ha).
Ha
Hb
8 mm
Open the appliance door and the kitchen
furniture door at an angle of 90°.
Insert the small square (Hb) into guide
(Ha).
Put together the appliance door and the
furniture door and mark the holes.
20www.aeg.com