AEG Integrated fridge freezer SCT71900S0 User Manual

							1. If necessary cut the adhesive sealing
strip and then apply it to the appliance
as shown in figure.
2. Drill the hinge cover A, as shown in fig-
ure.
Apply the covers A and A1 (in the acces-
sories bag) in to the middle hinge.
3. Install the appliance in the niche.
Push the appliance in the direction of
the arrow (1) until the upper gap cover
stops against the kitchen furniture.
Push the appliance in the direction of
the arrow (2) against the cupboard on
the opposite side of the hinge.
x
x
A1 A
1 2
Installation21 
						

							4. Adjust the appliance in the niche.
Make sure that the distance between
the appliance and the cupboard front-
edge is 44 mm.
The lower hinge cover (in the accessories
bag) makes sure that the distance be-
tween the appliance and the kitchen
furniture is correct.
Make sure that the clearance between
the appliance and the cupboard is 4
mm.
Open the door. Put the lower hinge cov-
er in position.
5. Attach the appliance to the niche with 4
screws.
6. Remove the correct part from the hinge
cover (E). Make sure to remove the part
DX, in the case of right hinge, SX in op-
posite case.
44mm
4mm
I
I
22Installation 
						

							7. Attach the covers (C, D) to the lugs and
the hinge holes.
Install the vent grille (B).
Attach the hinge covers (E) to the hinge.
8. If the appliance must connect laterally
to the kitchen furniture door:
a) Slacken the screws in fixing brackets
(H).
b) Move the brackets (H).
c) Retighten the screws.
9. Disconnect the parts (Ha), (Hb), (Hc) and
(Hd)
BE
E
DC
HH
Installation23 
						

							10. Install the part (Ha) on the inner side of
the kitchen furniture.
11. Push the part (Hc) on the part (Ha).
12. Open the appliance door and the kitch-
en furniture door at an angle of 90°.
Insert the small square (Hb) into guide
(Ha).
Put together the appliance door and the
furniture door and mark the holes.ca. 50 mm
ca. 50 mm21 mm 90°       
90°       
21 mm
Ha
Hc
Ha
Hb
8 mm
24Installation 
						

							13. Remove the brackets and mark a dis-
tance of 8 mm from the outer edge of
the door where the nail must be fitted
(K).
14. Place the small square on the guide
again and fix it with the screws sup-
plied.
Align the kitchen furniture door and the
appliance door by adjusting the part Hb.
15. Press the part (Hd) on the part (Hb).
Do a final check to make sure that:
• All screws are tightened.
• The sealing strip is attached tightly to the
cabinet.
• The door opens and closes correctly.
NOISES
There are some sounds during normal running (compressor, refrigerant circulation).
Ha K
8 mm
Hb
Hb
Hd
Noises25 
						

							BRRR! HISSS!
CLICK!
BLUBB!
CRACK!
SSSRRR!
OK
CLICK!CLICK!
BRRR!
BRRR!
BLUBB!BLUBB!
26Noises 
						

							HISSS!
HISSS!
SSSRRR!SSSRRR!
CRACK!
CRACK!
ENVIRONMENTAL CONCERNS
The symbol  on the product or on its packaging indicates that this product may not be
treated as household waste. Instead it should be taken to the appropriate collection point
for the recycling of electrical and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste
handling of this product. For more detailed information about recycling of this product,
please contact your local council, your household waste disposal service or the shop where
you purchased the product.Environmental concerns
27 
						

							www.aeg.com/shop222356012-B-032011