AEG Integrated fridge freezer SCS51810S1 User Manual

							About 12 hours prior to
defrosting, set a lower
temperature, in order to
build up sufficient chill
reserve for the interruption
in operation.
A certain amount of frost will always form
on the freezer shelves and around the
top compartment.
Defrost the freezer when the frost layer
reaches a thickness of about 3-5 mm.
1. Switch off the appliance, or pull out
electrical plug from the wall socket.
2. Remove any stored food, wrap it in
several layers of newspaper and put
it in a cool place. 
WARNING!
Do not touch frozen
goods with wet hands.
Hands can freeze to the
goods.
3. Leave the door open. 
In order to speed up the defrosting process, place a pot of warm water inthe freezer compartment. In addition,
remove pieces of ice that break away
before defrosting is complete.
4. When defrosting is completed, dry
the interior thoroughly.
5. Switch on the appliance.
After three hours reload the previously removed food into the freezer
compartment.6.5  Periods of non-operation
When the appliance is not in use for long
periods, take the following precautions:
1. Disconnect the appliance from
electricity supply.
2. Remove all food.
3. Defrost (if necessary) and clean the
appliance and all accessories.
4. Clean the appliance and all
accessories.
5. Leave the door/doors open to
prevent unpleasant smells.
WARNING!
If the cabinet will be kept on,
ask somebody to check it
once in a while to prevent
the food inside from spoiling
in case of a power failure.7.  TROUBLESHOOTINGWARNING!
Refer to Safety chapters.7.1  What to do if...ProblemPossible causeSolutionThe appliance does not op-
erate.The appliance is switched
off.Switch on the appliance. The mains plug is not con-
nected to the mains socket
correctly.Connect the mains plug to the
mains socket correctly. There is no voltage in the
mains socket.Connect a different electrical
appliance to the mains socket.
Contact a qualified electrician.The appliance is noisy.The appliance is not sup-
ported properly.Check if the appliance stands
stable.ENGLISH11     
						

							ProblemPossible causeSolutionThe lamp does not work.The lamp is in stand-by.Close and open the door.The lamp does not work.The lamp is defective.Contact the nearest Author-
ised Service Centre.The compressor operates
continually.Temperature is set incor-
rectly.Refer to "Operation" chapter. Many food products were
put in at the same time.Wait some hours and then
check the temperature again. The room temperature is
too high.Refer to climate class chart on
the rating plate. Food products placed in
the appliance were too
warm.Allow food products to cool to
room temperature before stor-
ing.The door is not closed cor-
rectly.Refer to "Closing the door".The FROSTMATIC function
is switched on.Refer to "FROSTMATIC func-
tion".The water drainage plug is
not correctly positioned.Position the water drainage
plug in the correct way.Food products are not
wrapped properly.Wrap the food products bet-
ter.Temperature is set incor-
rectly.Refer to "Operation" chapter.The compressor does not
start immediately after
pressing the FROSTMATIC,
or after changing the tem-
perature.This is normal, no error has
occurred.The compressor starts after a
period of time.Water flows inside the refrig-
erator.The water outlet is clog-
ged.Clean the water outlet.Food products prevent
that water flows into the
water collector.Make sure that food products
do not touch the rear plate.Water flows on the floor.The melting water outlet is
not connected to the
evaporative tray above the
compressor.Attach the melting water out-
let to the evaporative tray.www.aeg.com12 
						

							ProblemPossible causeSolutionTemperature cannot be set.The FROSTMATIC or
COOLMATIC function is
switched on.Switch off FROSTMATIC or
COOLMATIC manually, or wait
until the function resets auto-
matically to set the tempera-
ture. Refer to "FROSTMATIC
or COOLMATIC function".The temperature in the ap-
pliance is too low/too high.The temperature regulator
is not set correctly.Set a higher/lower tempera-
ture.The door is not closed cor-
rectly.Refer to "Closing the door".The food products' tem-
perature is too high.Let the food products temper-
ature decrease to room tem-
perature before storage.Many food products are
stored at the same time.Store less food products at the
same time.The thickness of the frost is
greater than 4-5 mm.Defrost the appliance.The door has been
opened often.Open the door only if necessa-
ry.The FROSTMATIC function
is switched on.Refer to "FROSTMATIC func-
tion".There is no cold air circula-
tion in the appliance.Make sure that there is cold air
circulation in the appliance.If the advice does not lead
to the desired result, contact
the nearest Authorised
Service Centre.7.2  Replacing the lamp
The appliance is equipped with a longlife
LED interior light.
Only service is allowed to replace the
lighting device. Contact your Authorised Service Centre.
7.3  Closing the door
1. Clean the door gaskets.
2. If necessary, adjust the door. Refer to
"Installation".
3. If necessary, replace the defective
door gaskets. Contact the Authorised
Service Centre.8.  INSTALLATION8.1  Positioning
This appliance can be installed in a dry,
well ventilated indoor where the ambient temperature corresponds to the climateclass indicated on the rating plate of theappliance:ENGLISH13  
						

							Climate
classAmbient temperatureSN+10°C to + 32°CN+16°C to + 32°CST+16°C to + 38°CT+16°C to + 43°CSome functional problems
might occur for some types
of models when operating
outside of that range. The
correct operation can only
be guaranteed within the
specified temperature
range. If you have any
doubts regarding where to
install the appliance, please
turn to the vendor, to our
customer service or to the
nearest Authorised Service
Centre.8.2  Electrical ConnectionCAUTION!
Any electrical work required to install this appliance
should be carried out by a
qualified electrician or
competent person.WARNING!
This appliance must be
earthed.
The manufacturer declines
any liability should these
safety measures not be
observed.
The wires in the mains lead are coloured
in accordance with the following code:
• A - green and yellow: Earth
• C - brown: Live
• D - blue: Neutral
As the colours of the wires in the mains
lead of this appliance may not
correspond with the coloured markings
identifying the terminals in your plug,
proceed as follows:
1. Connect the wire coloured green and
yellow to the terminal marked either
with the letter “E“ or by the earth
symbol 
 or coloured green and
yellow.
2. Connect the wire coloured blue to
the terminal either marked with the
letter “N“ or coloured black.
3. Connect the wire coloured brown to
the terminal either marked with the
“L“ or coloured red.
4. Check that no cut, or stray strands of
wire is present and the cord clamp
( E ) is secure over the outer sheath. 
Make sure the electricity supply
voltage is the same as that indicated
on the appliance rating plate.
5. Switch on the appliance.
The appliance is supplied with a 13 amp
fuse ( B). In the event of having to change
the fuse in the plug supplied, a 13 amp
ASTA approved (BS 1362) fuse must be
used.
WARNING!
A cut off plug inserted into a
13 amp socket is a serious
safety (shock) hazard. Ensure
that it is disposed of safely.www.aeg.com14   A BC D E    
						

							8.3 Ventilation requirements
The airflow behind the appliance must
be sufficient.CAUTION!
Refer to the assembly instructions for the
installation.8.4  Door reversibility
1.Loosen and remove the upper pin.
2. Remove the upper door.
3. Remove the spacer.
4. Loosen the middle hinge.
5.Remove the lower door.
6. Loosen and remove the lower pin.
7.Tighten the lower pin on the
opposite side.
8. Install the lower door.
9. Tighten the middle hinge.
10. Install the spacer.
11. Install the upper door.
12. Tighten the upper pin.
Do a final check to make
sure that:
• All screws are tightened. • The magnetic seal adheres to the cabinet.
• The door opens and closes correctly.
If the ambient temperature
is cold (i.e. in Winter), the
gasket may not fit perfectly
to the cabinet. In that case,
wait for the natural fitting of
the gasket.
In case you do not want to
carry out the above
mentioned operations,
contact the nearest
Authorised Service Centre.
The Authorised Service
specialist will carry out the
reversibility of the doors at
your cost.8.5  Installing the applianceCAUTION!
Make sure that the mains
cable can move freely.
1. If necessary cut the adhesive sealing
strip and then apply it to the
appliance as shown in figure.
ENGLISH155 cmmin. 
200 cm2
min. 200 cm
2        
						

							2.Install the appliance in the niche.
3. Push the appliance in the direction of
the arrows (1) until the upper gap cover stops against the kitchen
furniture.
4. Push the appliance in the direction of
the arrows (2) against the cupboard on the opposite side of the hinge.
5. Adjust the appliance in the niche. 
Make sure that the distance between
the appliance and the cupboard front-edge is 44 mm.
The lower hinge cover (in the
accessories bag) makes sure that the
distance between the appliance and
the kitchen furniture is correct.
Make sure that the clearance
between the appliance and the
cupboard is 4 mm.
6. Open the door. Put the lower hinge
cover in position.
7. Attach the appliance to the niche
with 4 screws.
8. Remove the correct part from the
hinge cover (E). Make sure to remove the part DX, in the case of right
hinge, SX in opposite case.
www.aeg.com16x
x 1
2 4 mm
44 mm II  
						

							9.Attach the covers (C, D) to the lugs
and the hinge holes.
10. Install the vent grille (B).
11. Attach the hinge covers (E) to the
hinge.
12. Connect the appliance laterally to
the kitchen furniture sidewall.
13. Loosen the screws of the part (G) and
move the part (G) till the furniture
sidewall.
14. Tighten the screws of the part (G)
again.
15. Attach the part (H) to the part (G).
16. Disconnect the parts (Ha), (Hb), (Hc)
and (Hd).
17. Install the part (Ha) on the inner side
of the kitchen furniture.
18. Push the part (Hc) on the part (Ha).
ENGLISH17 EEB
D
C GH Hb HaHc
Hd ca. 50 mm
ca. 50 mm 21 mm
90°        90°       
21 mm  
						

							19.Open the appliance door and the
kitchen furniture door at an angle of
90°.
20. Insert the small square (Hb) into
guide (Ha).
21. Put together the appliance door and
the furniture door and mark the
holes.
22. Remove the brackets and mark a
distance of 8 mm from the outer
edge of the door where the nail must
be fitted (K).
23. Place the small square on the guide
again and fix it with the screws
supplied.
24. Align the kitchen furniture door and
the appliance door by adjusting the
part (Hb).
25. Press the part (Hd) on the part (Hb).
Do a final check to make sure that:
• All screws are tightened.
• The sealing strip is attached tightly to the cabinet.
• The door opens and closes correctly.
www.aeg.com18Ha
Hc Ha
Hb 8 mm Ha
K
8 mm Hb HbHd  
						

							9. NOISES
There are some sounds during normal running (compressor, refrigerant circulation).
ENGLISH19BRRR!
HISSS!
CLICK!
BLUBB!
CRACK!
SSSRR
R!
OK CLICK!CLICK!SSSRRR!SSSRRR! BRRR!BRRR!HISSS!HISSS!  
						

							10. TECHNICAL INFORMATION10.1  Technical data   Dimensions of the recess  Heightmm1780Widthmm560Depthmm550Rising timeHours22VoltageVolts230 - 240FrequencyHz50The technical information are situated in
the rating plate, on the external orinternal side of the appliance and in the energy label.11.  ENVIRONMENT CONCERNSRecycle the materials with the symbol .
Put the packaging in applicable
containers to recycle it. Help protect the
environment and human health and to recycle waste of electrical and electronic
appliances. Do not dispose appliancesmarked with the symbol  with the
household waste. Return the product to
your local recycling facility or contact
your municipal office.
*
www.aeg.com20BLUBB!BLUBB!CRACK!CRACK!