AEG Integrated freezer AGN71200C1 User Manual
Have a look at the manual AEG Integrated freezer AGN71200C1 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 513 AEG manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
ProblemPossible causeSolution The mains plug is not con- nected to the mains socket correctly.Connect the mains plug to the mains socket correctly. There is no voltage in the mains socket.Connect a different electrical appliance to the mains sock- et. Contact a qualified elec- trician.The appliance is noisy.The appliance is not suppor- ted properly.Check if the appliance stands stable.Audible or visual alarm is on.The cabinet has been re- cently switched on or the temperature is still too high.Refer to "Door Open Alarm"or "High Tempera- ture Alarm".The temperature in the ap- pliance is too high.Refer to "Door Open Alarm"or "High Tempera- ture Alarm".The door is left open.Close the door.The temperature in the ap- pliance is too high.Contact a qualified electri- cian or contact the nearest Authorized Service Centre.A rectangular symbol is shown instead of numbers on the Temperature Display.Temperature sensor prob- lem.Contact the nearest Author- ized Service Centre (the cooling system will continue to keep food products cold, but temperature adjustment will not be possible).The compressor operates continually.Temperature is set incorrect- ly.Refer to "Operation" chap- ter. Many food products to be frozen were put in at the same time.Wait some hours and then check the temperature again. The room temperature is too high.Refer to climate class chart on the rating plate. Food products placed in the appliance were too warm.Allow food products to cool to room temperature before storing.The door is not closed cor- rectly.Refer to "Closing the door".The FROSTMATIC function is switched on.Refer to "FROSTMATIC function".ENGLISH11
ProblemPossible causeSolutionThere is too much frost and ice.The door is not closed cor- rectly or the gasket is de- formed/dirty.Refer to "Closing the door".Food products are not wrap- ped properly.Wrap the food products bet- ter.The compressor does not start immediately after pressing the FROSTMATIC, or after changing the tem- perature.This is normal, no error has occurred.The compressor starts after a period of time.Water flows on the floor.The melting water outlet is not connected to the evapo- rative tray above the com- pressor.Attach the melting water outlet to the evaporative tray.Temperature cannot be set.The FROSTMATIC or COOL- MATIC function is switched on.Switch off FROSTMATIC or COOLMATIC manually, or wait until the function resets automatically to set the tem- perature. Refer to "FROST- MATIC or COOLMATIC function".DEMO appears on the dis- play.The appliance is in demon- stration mode.Keep the OK button pressed for approximately 10 sec- onds until a long sound is heard and display shuts off for a short time.The temperature in the ap- pliance is too low/too high.The temperature regulator is not set correctly.Set a higher/lower tempera- ture.The door is not closed cor- rectly.Refer to "Closing the door".The food products' tempera- ture is too high.Let the food products tem- perature decrease to room temperature before storage.Many food products are stored at the same time.Store less food products at the same time.The door has been opened often.Open the door only if neces- sary.The FROSTMATIC function is switched on.Refer to "FROSTMATIC function".There is no cold air circula- tion in the appliance.Make sure that there is cold air circulation in the appli- ance.www.aeg.com12
If the advice does not lead to the desired result, call the nearest Authorized Service Centre.8.2 Closing the door 1.Clean the door gaskets. 2.If necessary, adjust the door. Refer to "Installation". 3. If necessary, replace the defective door gaskets. Contact the Authorised Service Centre.9. INSTALLATIONWARNING! Refer to Safety chapters.9.1 LocationRefer to the assembly instructions for the installation. To ensure best performance, install the appliance well away from sources of heat such as radiators, boilers, direct sunlight etc. Make sure that air can circulate freely around the back of the cabinet. 9.2 Positioning This appliance can be installed in a dry, well ventilated indoor where the ambient temperature corresponds to the climateclass indicated on the rating plate of theappliance: Climate classAmbient temperatureSN+10°C to + 32°CN+16°C to + 32°CST+16°C to + 38°CT+16°C to + 43°CSome functional problems might occur for some types of models when operating outside of that range. The correct operation can only be guaranteed within the specified temperature range. If you have any doubts regarding where to install the appliance, please turn to the vendor, to our customer service or to the nearest Authorised Service Centre.9.3 Ventilation requirements The airflow behind the appliance must be sufficient. 9.4 Electrical ConnectionCAUTION! Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person.ENGLISH13 5 cmmin. 200 cm2 min. 200 cm 2
WARNING! This appliance must be earthed. The manufacturer declines any liability should these safety measures not be observed. The wires in the mains lead are coloured in accordance with the following code: • A - green and yellow: Earth • C - brown: Live • D - blue: Neutral As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: 1. Connect the wire coloured green and yellow to the terminal marked either with the letter “E“ or by the earth symbol or coloured green and yellow. 2. Connect the wire coloured blue to the terminal either marked with the letter “N“ or coloured black. 3. Connect the wire coloured brown to the terminal either marked with the “L“ or coloured red. 4. Check that no cut, or stray strands of wire is present and the cord clamp ( E ) is secure over the outer sheath. Make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. 5. Switch on the appliance. The appliance is supplied with a 13 amp fuse ( B). In the event of having to change the fuse in the plug supplied, a 13 amp ASTA approved (BS 1362) fuse must be used. WARNING! A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure that it is disposed of safely.10. NOISES There are some sounds during normal running (compressor, refrigerant circulation). www.aeg.com14 A BC D E BRRR! HISSS! CLICK! BLUBB! CRACK! SSSRR R! OK
11. TECHNICAL INFORMATION11.1 Technical data Heightmm1224Widthmm556Depthmm549Rising timeHours24ENGLISH15CLICK!CLICK!SSSRRR!SSSRRR! BRRR!BRRR!HISSS!HISSS! BLUBB!BLUBB!CRACK!CRACK!
VoltageVolts230 - 240FrequencyHz50The technical information are situated in the rating plate, on the external orinternal side of the appliance and in the energy label.12. ENVIRONMENT CONCERNSRecycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliancesmarked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office. * www.aeg.com16