AEG Integrated dishwasher F99705VI1P User Manual

							option and Done. If you want toselect another option select again Add option otherwise select 
Done.
9. Press the  OK key.
If the programme has the TimeSaver
option, you have to select Fast or 
Normal.10. Press the  OK key to confirm.
The display confirms that the 
MyFavourite programme has been
saved.7.  OPTIONS7.1  Option listOptionsValuesDescriptionDelay startFrom 1 to 24 hours
OFF (default value)Delay the start of the pro-
gramme.AutoOpenON (default value)
OFFThe use of this option saves
energy by opening the ap-
pliance door during the dry-
ing phase. Refer to specific
information provided in this
chapter.
This option is applicable on-
ly to the programme ECO.Extra HygieneON
OFF (default value)The use of this option sani-
tizes cutlery and tableware.
During the last rinsing
phase, the temperature stays
at 70 °C for at least 10 mi-
nutes.ProBoostON
OFF (default value)The use of this option gives
very good washing results
for heavy soiled dishes. The
water pressure in the pre-
wash and washing phases is
increased.MultitabON
OFF (default value)Activate this option if you
want to use multi-tablets.
Refer to specific information
provided in this chapter.SettingsEnter appliance settings 7.2  How to set an option
The option list will show only the options applicable to the currently selected
programme. Non applicable options are
not visible.Some options are not compatible with
each other. When you set 2 options that
are not compatible with each other, the appliance will automatically deactivate
one of the options.ENGLISH11 
						

							When the programme is completed or is
cancelled the options are set to the
default values.
1. Press the  Option key.
2. Select an option.
The display shows the option value indicated in parenthesis.
3. Press the  OK key to change the value
from OFF to ON or vice versa.
If the selected option is Delay start, when
you press the  OK key the display shows
the number of hours available for the
delay start. Select the number of hours
and press again the  OK key to confirm.
4. To go back to the programme list,
press repeatedly the  Option key until
the display shows the selected
programme.7.3  Multitab
Activate this option when you use multi-
tablets that integrate the salt, rinse aid
and detergent functions. They can also
contain other cleaning or rinsing agents.
This option deactivates the release of salt from the respective container. The
salt refilling message does not show in the display.
With the use of this option the
programme duration is prolonged to
increase the cleaning and drying results
with the use of multi-tablets.
When you activate the option Multitab
the rinse aid dispenser continues to
release rinse aid. However you can
deactivate the rinse aid dosage by
setting the rinse aid level at 0. In this
case the drying results may not be
satisfactory.
The option Multitab is not a permanent option and must be selected at every
cycle.
7.4  TimeSaver
This option increases the pressure and
the temperature of the water.
The washing and drying phases are
shorter. The total programme duration decreases by approximately 50%.
The washing results are the same as with
the normal programme duration but the
drying results can be less satisfactory.
The TimeSaver option is not applicable
to all programmes.
1. Scroll through the programme list
and select a programme.
2. Press the  OK key to confirm.
If the TimeSaver option is applicable to
the selected programme, the display
shows the 2 conditions Fast and Normal
and the programme duration for each
condition:
• Fast: TimeSaver activated. Pressthe  OK key to confirm.
• Normal: TimeSaver deactivated. Press the  OK key to confirm.7.5  AutoOpen
This option is automatically activated
when you select the programme ECO
and it is not possible to select this option with other programmes.
You can deactivate AutoOpen in the
option list. In this case, the energy
consumption increases.
• While the drying phase operates, a device opens the appliance door andkeeps it ajar.
• At the end of the programme, the device retracts but the appliance doorcan remain ajar or retract without
closing.
CAUTION!
Do not try to close the appliance door while the
device keeps the door ajar.
This can cause damage to the
appliance.www.aeg.com12   
						

							8. BEFORE FIRST USE1.Set the language.
• Press  OK to confirm English.
• Scroll the list of available languages for a new language
and press  OK to confirm.
2. Make sure that the current level of the water softener agrees with the
hardness of the water supply. If
not, adjust the level of the water softener.
3. Fill the salt container.
4. Fill the rinse aid dispenser.
5. Open the water tap.
6. Start a programme to remove any
processing residuals that can still be
inside the appliance. Do not use
detergent and do not load the
baskets.
When you start a programme, the
appliance can take up to 5 minutes to recharge the resin in the water softener.It seems that the appliance is not
working. The washing phase starts only after this procedure is completed. The
procedure will be repeated periodically.8.1  The water softener
The water softener removes minerals
from the water supply, which would have a detrimental effect on the washingresults and on the appliance.
The higher the content of these minerals, the harder your water is. Water hardness
is measured in equivalent scales.
The water softener should be adjusted
according to the hardness of the water in your area. Your local water authority can
advise you on the hardness of the water in your area. It is important to set the
right level of the water softener to assure good washing results.
Water hardnessGerman de-
grees (°dH)French degrees (°fH)mmol/lClarke de-greesWater softener lev- el47 - 5084 - 908.4 - 9.058 - 631043 - 4676 - 837.6 - 8.353 - 57937 - 4265 - 756.5 - 7.546 - 52829 - 3651 - 645.1 - 6.436 - 45723 - 2840 - 504.0 - 5.028 - 35619 - 2233 - 393.3 - 3.923 - 275 1)15 - 1826 - 322.6 - 3.218 - 22411 - 1419 - 251.9 - 2.513 - 1734 - 107 - 180.7 - 1.85 - 122
						

							How to fill the salt container1. Turn the cap of the salt container
counterclockwise and remove it.
2. Put 1 litre of water in the salt
container (Only for the first time).
3. Fill the salt container with dishwasher
salt.
4. Remove the salt around the opening
of the salt container.
5. Turn the cap of the salt container
clockwise to close the salt container.
Water and salt can come out
from the salt container when
you fill it. Risk of corrosion. To
prevent it, after you fill the salt
container, start a programme.When the salt container needs
refilling, the display shows a
message.8.3  The rinse aid dispenser
The rinse aid helps to dry the dishes
without streaks and stains.
The rinse aid is automatically released
during the hot rinse phase.
You can set the released quantity of rinse
aid between level 1 (minimum quantity)
and level 6 (maximum quantity). Level 0
will deactivate the rinse aid dispenser
and no rinse aid will be released.
Factory setting: level 4.How to fill the rinse aid
dispenserCAUTION!
Only use rinse aid specifically designed for dishwashers.
1. Open the lid ( C).
2. Fill the dispenser ( B) until the rinse
aid reaches the marking ''MAX''.
3. Remove the spilled rinse aid with an
absorbent cloth to prevent too much
foam.
4. Close the lid. Make sure that the lid
locks into position.
Fill the rinse aid dispenser
when the indicator ( A)
becomes clear.When the rinse aid dispenser
needs refilling, the display
shows a message.9.  DAILY USE1.Open the water tap.
2. Press the on/off button to activate
the appliance.• If the display shows the salt refilling message, fill the saltcontainer.www.aeg.com14    AB
C     
						

							• If the display shows the rinse aidrefilling message, fill the rinse aid
dispenser.
3. Load the baskets.
4. Add the detergent. If you use multi-
tablets, activate the option Multitab.
5. Set and start the correct programme
for the type of load and the degree
of soil.9.1  Using the detergentCAUTION!
Only use detergent specifically designed for
dishwashers.
1. Press the release button ( A) to open
the lid ( C).
2. Put the detergent, in powder or
tablets, in the compartment ( B).
3. If the programme has a prewash
phase, put a small quantity of
detergent on the inner part of the
appliance door.
4. Close the lid. Make sure that the lid
locks into position.
9.2  Setting and starting a
programmeThe Auto Off function
This function decreases energy
consumption by deactivating
automatically the appliance when it is not operating.
The function comes into operation: • 5 minutes after the completion of the programme.
• After 5 minutes if the programme has not started.
Starting a programme
When you activate the appliance, the
display shows the programme list. The
programme ECO is always the default programme.
1. Scroll the programme list and select
a programme.
2. Select applicable options if desired.
Once options are set, go back to the
programme list to start the selected
programme.
3. Press  OK.
If the programme is applicable to the
option TimeSaver, you have to confirm  Fast or Normal.
4. Close the appliance door to start the
programmeHow to delay the start of a
programme
It is not possible to set the delay start with the MyFavourite programme.
1. Select a programme.
2. Press  Option .
The display shows the option list.
3. Select Delay start.
4. Press  OK.
5. Select the number of hours desired
for the delay start.
You can delay the start of a programme
from 1 to 24 hours.
6. Press  OK to confirm.
7. You can select other applicable
options.
8. Press repeatedly  Option until the
display shows the selected
programme.
9. Press  OK.
10. Close the appliance door to start the
countdown of the delay start.
When the countdown is completed, the
programme starts automatically.
Starting the MyFavourite
programme
1. Press and hold  OK for about 3
seconds until the display shows the 
MyFavourite setting.
2. Close the appliance door to start the
programme.
ENGLISH15AB
C   
						

							Opening the door while the
appliance operates
If you open the door while a programme is running, the appliance stops. When
you close the door, the appliance
continues from the point of interruption.If the door is opened for more
that 30 seconds during the
drying phase, the running
programme will end. This will
not happen when programme
ECO with AutoOpen is
running.Cancelling the delay start while
the countdown operates
When you cancel the delay start the
programme and the options are set to
their default values.
1. Open the appliance door.
2. Press and hold  Option for about 3
seconds until the display shows Stop
washing?. • Select Resume and press  OK to
continue with the countdown.
Close the appliance door.
• Select Stop and press  OK to
cancel the delay start.Cancelling a running
programme
When you cancel the running
programme the options are set to their
default values.
1. Open the appliance door.
2. Press and hold  Option for about 3
seconds until the display shows Stop
washing?. • Select Resume and press  OK to
continue with the running
programme. Close the appliance
door.
• Select Stop and press  OK to
cancel the running programme.
End of programme
When the programme is completed the 
TimeBeam shows 0:00 and CLEAN. The
appliance is automatically deactivated
when you open the door.
Close the water tap.
10.  HINTS AND TIPS10.1  General
The following hints will ensure optimal
cleaning and drying results in daily use
and also help to protect the
environment.
• Remove larger residues of food from the dishes into the waste bin.
• Do not pre-rinse dishes by hand. When needed, use the prewash
programme (if available) or select a
programme with a prewash phase.
• Always use the whole space of the baskets.
• When loading the appliance, make sure that the dishes can be
completely reached and washed by
the water released from the spray arm
nozzles. Make sure that items do not
touch or cover each other.
• You can use dishwasher detergent, rinse aid and salt separately or you
can use the multi-tablets (e.g. ''3in1'',''4in1'', ''All in 1''). Follow the
instructions written on the packaging.
Multi-tablets are usually suitable in
areas with a water hardness up to 21 °dH. In areas exceeding this limit,
rinse aid and salt must also be used. If
you use multi-tablets you can select
the Multitab option (if available). This
option increases the cleaning and
drying results with the use of multi-
tablets.
• Select the programme according to the type of load and degree of soil.
With the ECO programme you have
the most efficient use of water and energy consumption for crockery and
cutlery with normal soil.www.aeg.com16  
						

							10.2 Using salt, rinse aid and
detergent
• Only use salt, rinse aid and detergent for dishwasher. Other products cancause damage to the appliance.
• Multi-tablets are usually suitable in areas with a water hardness up to 21°dH. In areas exceeding this limit,
rinse aid and salt must be used in
addition to the multi-tablets.
However, in areas with hard and very
hard water we recommend to use
solo-detergent (powder, gel, tablets
without additional functions), rinse aid
and salt separately for optimal
cleaning and drying results.
• If you use multi-tablets you can select the Multitab option (if available). Thisoption increases the cleaning and
drying results with the use of multi-
tablets.
• Detergent tablets do not fully dissolve with short programmes. To prevent
detergent residues on the tableware,
we recommend that you use the
tablets with long programmes.
• Do not use more than the correct quantity of detergent. Refer to theinstructions on the detergent
packaging.10.3  What to do if you want to
stop using multi-tablets
Before you start to use separately
detergent, salt and rinse aid do the
following procedure.
1. Set the highest level of the water
softener.
2. Make sure that the salt and rinse aid
containers are full.
3. Start the shortest programme with a
rinsing phase. Do not add detergent
and do not load the baskets.
4. When the programme is completed,
adjust the water softener according
to the water hardness in your area.
5. Adjust the released quantity of rinse
aid.
10.4  Loading the baskets
• Only use the appliance to wash items
that are dishwasher-safe.
• Do not put in the appliance items made of wood, horn, aluminium,
pewter and copper.
• Do not put in the appliance items that can absorb water (sponges,
household cloths).
• Remove larger residues of food from the dishes into the waste bin.
• Make soft the remaining burned food on the items.
• Put hollow items (cups, glasses and pans) with the opening down.
• Make sure that glasses do not touch other glasses.
• Put cutlery and small items in the cutlery drawer.
• Put light items in the upper basket. Make sure that the items do not
move.
• Make sure that the spray arm can move freely before you start a
programme.10.5  Before starting a
programme
Make sure that:
• The filters are clean and correctly installed.
• The cap of the salt container is tight. • The spray arms are not clogged.• There is dishwasher salt and rinse aid (unless you use multi- tablets).
• The position of the items in the baskets is correct.
• The programme is applicable for the type of load and for the degree of
soil.
• The correct quantity of detergent is used.
10.6  Unloading the baskets
1.Let the tableware cool down before
you remove it from the appliance.
Hot items can be easily damaged.
2. First remove items from the lower
basket, then from the upper basket.
At the end of the programme
water can still remain on the
sides and on the door of the
appliance.ENGLISH17  
						

							11. CARE AND CLEANINGWARNING!
Before maintenance,
deactivate the appliance and
disconnect the mains plug
from the main socket.Dirty filters and clogged spay
arms decrease the washing
results. Make a check regularly
and, if necessary, clean them.11.1  Cleaning the filters
The filter system is made of 3 parts.
1.Turn the filter ( B) counterclockwise
and remove it.
2. Remove the filter ( C) out of filter ( B).
3. Remove the flat filter ( A).
4. Wash the filters.
5.Make sure that there are no residues
of food or soil in or around the edge
of the sump.
6. Put back in place the flat filter ( A).
Make sure that it is correctly
positioned under the 2 guides.
7. Reassemble the filters ( B) and ( C).
8. Put back the filter ( B) in the flat filter
( A ). Turn it clockwise until it locks.
www.aeg.com18  C BA       
						

							CAUTION!
An incorrect position of the
filters can cause bad washing
results and damage to the
appliance.11.2  Cleaning the spray arms
Do not remove the spray arms. If the
holes in the spray arms are clogged,
remove remaining parts of soil with a thin
pointed object.11.3  External cleaning
• Clean the appliance with a moist soft
cloth.
• Only use neutral detergents.
• Do not use abrasive products, abrasive cleaning pads or solvents.
11.4  Internal cleaning
• Carefully clean the appliance,
including the rubber gasket of the
door, with a soft moist cloth.
• If you regularly use short duration programmes, these can leave
deposits of grease and limescale inside the appliance. To prevent this,
we recommend to run long duration
programmes at least 2 times per month.
12.  TROUBLESHOOTINGIf the appliance does not start or it stops
during operation. Before you contact an Authorised Service Centre, check if youcan solve the problem by yourself with
the help of the information in the table.With some problems, the display shows a message.ProblemPossible solutionYou cannot activate the appli-
ance.• Make sure that the mains plug is connected to the mains socket.
• Make sure that there is no a damage fuse in the fuse box.The programme does not start.• Make sure that the appliance door is closed.• If the delay start is set, cancel the setting or wait for the end of the countdown.
• The appliance has started the procedure to re- charge the resin inside the water softener. The du-
ration of the procedure is approximately 5 minutes.ENGLISH19   
						

							ProblemPossible solutionThe appliance does not fill with
water.
The display shows the message: 
Appliance is not filling water.• Make sure that the water tap is open.
• Make sure that the pressure of the water supply is not too low. For this information, contact your local
water authority.
• Make sure that the water tap is not clogged.
• Make sure that the filter in the inlet hose is not clog- ged.
• Make sure that the inlet hose has no kinks or bends.The appliance does not drain the
water.
The display shows the message: 
Appliance is not draining water.• Make sure that the sink spigot is not clogged.
• Make sure that the drain hose has no kinks or bends.The anti-flood device is on.
The display shows the message: 
Appliance is flooding or has an
error in the water inlet.• Close the water tap and contact an Authorised Serv- ice Centre.Once you have checked the appliance,deactivate and activate the appliance. Ifthe problem occurs again, contact an
Authorised Service Centre.For other alarm messages or problems
not described in the table, contact an Authorised Service Centre.12.1  The washing and drying results are not satisfactoryProblemPossible solutionThere are whitish streaks or
bluish layers on glasses and
dishes.• The release quantity of rinse aid is too much. Adjust the rinse aid selector to a lower position.
• The quantity of detergent is too much.There are stains and dry water
drops on glasses and dishes.• The released quantity of rinse aid is not sufficient. Ad- just the rinse aid selector to a higher position.
• The quality of the rinse aid can be the cause.The dishes are wet.• The programme does not have a drying phase or has a drying phase with low temperature.
• The rinse aid dispenser is empty.
• The quality of the rinse aid can be the cause.
• The quality of the multi-tablets can be the cause. Try a different brand or activate the rinse aid dispenser and
use rinse aid and multi-tablets together.Refer to " Hints and tips " for
other possible causes.www.aeg.com20