AEG Integrated dishwasher F66603VI0P User Manual
Here you can view all the pages of manual AEG Integrated dishwasher F66603VI0P User Manual. The AEG manuals for Dishwasher are available online for free. You can easily download all the documents as PDF.
Page 11
• The indicators , , and go off. • The indicator continues to flash. • The display shows a number and the letter C. Each number refers to a different colour. – = TimeBeam deactivated. 3. Press again and again to change the colour. • You can see the different colours on the kitchen floor. 4. Press the on/off button to confirm the setting.7. OPTIONSDesired options must be activated every time before you start a programme. It is not possible to activate or deactivate options while a programme is...
Page 12
8. BEFORE FIRST USE1. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener. 2. Fill the salt container. 3. Fill the rinse aid dispenser. 4. Open the water tap. 5. Start a programme to remove any processing residuals that can still be inside the appliance. Do not use detergent and do not load the baskets. When you start a programme, the appliance can take up to 5 minutes to recharge the resin in the water...
Page 13
9. DAILY USE1.Open the water tap. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in user mode. • If the salt indicator is on, fill thesalt container. • If the rinse aid indicator is on, fill the rinse aid dispenser. 3. Load the baskets. 4. Add the detergent. If you use multi- tablets, activate the option Multitab. 5. Set and start the correct programme for the type of load and the degree of soil.9.1 Using the detergentCAUTION! Only use detergent specifically...
Page 14
Opening the door while the appliance operates If you open the door while a programme is running, the appliance stops. When you close the door, the appliance continues from the point of interruption.If the door is opened for more than 30 seconds during the drying phase, the running programme will end.Cancelling the delay start while the countdown operates When you cancel the delay start you have to set the programme and options again. Press and hold RESET until the appliance is in programme selection...
Page 15
10.3 What to do if you want to stop using multi-tablets Before you start to use separately detergent, salt and rinse aid do the following procedure. 1. Set the highest level of the water softener. 2. Make sure that the salt and rinse aid containers are full. 3. Start the shortest programme with a rinsing phase. Do not add detergent and do not load the baskets. 4. When the programme is completed, adjust the water softener according to the water hardness in your area. 5. Adjust the released quantity of...
Page 16
1.Turn the filter ( B) counterclockwise and remove it. 2. Remove the filter ( C) out of filter ( B). 3. Remove the flat filter ( A). 4. Wash the filters. 5.Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter ( A). Make sure that it is correctly positioned under the 2 guides. 7. Reassemble the filters ( B) and ( C). 8. Put back the filter ( B) in the flat filter ( A ). Turn it clockwise until it locks. CAUTION! An incorrect position...
Page 17
11.2 Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object.11.3 External cleaning • Clean the appliance with a moist soft cloth. • Only use neutral detergents. • Do not use abrasive products, abrasive cleaning pads or solvents. 11.4 Internal cleaning • Carefully clean the appliance, including the rubber gasket of the door, with a soft moist cloth. • If you regularly use short duration programmes, these...
Page 18
For alarm codes not described in the table, contact an Authorised Service Centre.12.1 The washing and drying results are not satisfactoryProblemPossible solutionThere are whitish streaks or bluish layers on glasses and dishes.• The release quantity of rinse aid is too much. Adjust the rinse aid selector to a lower position. • The quantity of detergent is too much.There are stains and dry water drops on glasses and dishes.• The released quantity of rinse aid is not sufficient. Ad- just the rinse aid...