AEG Integrated dishwasher F34300VI0 User Manual

							Make sure that the appliance is in
programme selection mode. • If the salt indicator is on, fill thesalt container.
• If the rinse aid indicator is on, fill the rinse aid dispenser.
3. Load the baskets.
4. Add the detergent.
5. Set and start the correct programme
for the type of load and the degree
of soil.8.1  Using the detergent
1.Press the release button ( B) to open
the lid ( C).
2. Put the detergent, in powder or
tablets, in the compartment ( A).
3. If the programme has a prewash
phase, put a small quantity of
detergent in the compartment ( D).
4. Close the lid. Make sure that the
release button locks into position.
8.2  Using the multi-tablets
When you use tablets, that contain salt
and rinse aid, do not fill the salt container
and the rinse aid dispenser.
1. Adjust the water softener to the
lowest level.
2. Set the rinse aid dispenser to the
lowest position.8.3  Setting and starting a
programmeStarting a programme
1. Keep the appliance door ajar.
2. Press the on/off button to activate
the appliance. Make sure that the
appliance is in programme selection
mode.
3. Press the programme button
repeatedly until the indicator of the programme you want to select
comes on.
4. Close the appliance door to start the
programme.
Starting a programme with
delay start
1. Set a programme.
2. Press Delay to delay the start of the
programme of 3 hours.
• The indicator 
 comes on.
3. Close the appliance door to start the
countdown.
When the countdown is completed, the programme starts.
Opening the door while the
appliance operates
If you open the door while a programme is running, the appliance stops. When
you close the door, the appliance
continues from the point of interruption.
Cancelling the delay start
Press and hold the programme button
until the appliance is in programme
selection mode.
When you cancel the delay start, you
have to set the programme again.
Cancelling the programme
Press and hold the programme button
until the appliance is in programme
selection mode.
ENGLISH1130
20
A B
D
C 2030
B
A D
C   
						

							Make sure that there is detergent in thedetergent dispenser before you start anew programme.End of the programme
When the programme is completed the
indicator 
 is on.
1. Press the on/off button to deactivate
the appliance.
2. Close the water tap.If you do not deactivate the
appliance within 5 minutes
all indicators goes off. This
helps to decrease energy
consumption.9.  HINTS AND TIPS9.1  General
The following hints will ensure optimal
cleaning and drying results in daily use
and also help to protect the
environment.
• Remove larger residues of food from the dishes into the waste bin.
• Do not pre-rinse dishes by hand. When needed, use the prewash
programme (if available) or select a
programme with a prewash phase.
• Always use the whole space of the baskets.
• When loading the appliance, make sure that the dishes can be
completely reached and washed by
the water released from the spray arm nozzles. Make sure that items do not touch or cover each other.
• You can use dishwasher detergent, rinse aid and salt separately or you
can use the multi-tablets (e.g. ''3in1'',
''4in1'', ''All in 1''). Follow the
instructions written on the packaging.
• Select the programme according to
the type of load and degree of soil.
With the ECO programme you have
the most efficient use of water and energy consumption for crockery andcutlery with normal soil.9.2  Using salt, rinse aid and
detergent
• Only use salt, rinse aid and detergent for dishwasher. Other products cancause damage to the appliance.
• Multi-tablets are usually suitable in areas with a water hardness up to 21°dH. In areas exceeding this limit,
rinse aid and salt must be used in
addition to the multi-tablets.
However, in areas with hard and very
hard water we recommend to use
solo-detergent (powder, gel, tablets
without additional functions), rinse aid
and salt separately for optimal
cleaning and drying results.
• If you use multi-tablets you can select the Multitab option (if available). Thisoption increases the cleaning and
drying results with the use of multi-
tablets.
• Detergent tablets do not fully dissolve with short programmes. To prevent
detergent residues on the tableware,
we recommend that you use the
tablets with long programmes.
• Do not use more than the correct quantity of detergent. Refer to the
instructions on the detergent
packaging.9.3  What to do if you want to
stop using multi-tablets
Before you start to use separately
detergent, salt and rinse aid do the
following procedure.
1. Set the highest level of the water
softener.
2. Make sure that the salt and rinse aid
containers are full.
3. Start the shortest programme with a
rinsing phase. Do not add detergent
and do not load the baskets.
4. When the programme is completed,
adjust the water softener according
to the water hardness in your area.
5. Adjust the released quantity of rinse
aid.
9.4  Loading the baskets
• Only use the appliance to wash items
that are dishwasher-safe.
www.aeg.com12   
						

							• Do not put in the appliance itemsmade of wood, horn, aluminium,pewter and copper.
• Do not put in the appliance items that can absorb water (sponges,
household cloths).
• Remove larger residues of food from the dishes into the waste bin.
• Make soft the remaining burned food on the items.
• Put hollow items (cups, glasses and pans) with the opening down.
• Make sure that glasses do not touch other glasses.
• Put cutlery and small items in the cutlery basket.
• Put light items in the upper basket. Make sure that the items do not
move.
• Make sure that the spray arms can move freely before you start a
programme.9.5  Before starting a
programme
Make sure that:
• The filters are clean and correctly installed.
• The cap of the salt container is tight. • The spray arms are not clogged.• There is dishwasher salt and rinse aid (unless you use multi- tablets).
• The position of the items in the baskets is correct.
• The programme is applicable for the type of load and for the degree ofsoil.
• The correct quantity of detergent is used.9.6  Unloading the baskets
1.Let the tableware cool down before
you remove it from the appliance.
Hot items can be easily damaged.
2. First remove items from the lower
basket, then from the upper basket.
At the end of the
programme water can still
remain on the sides and on
the door of the appliance.10.  CARE AND CLEANINGWARNING!
Before maintenance,
deactivate the appliance and
disconnect the mains plug
from the main socket.Dirty filters and clogged
spray arms decrease the
washing results. Make a
check regularly and, if
necessary, clean them.10.1  Cleaning the filters
The filter system is made of 3 parts.
1.Turn the filter ( B) counterclockwise
and remove it.
ENGLISH13   C BA  
						

							2.Remove the filter ( C) out of filter ( B). 
3. Remove the flat filter ( A).
4. Wash the filters.
5.Make sure that there are no residues
of food or soil in or around the edge
of the sump.
6. Put back in place the flat filter ( A).
Make sure that it is correctly
positioned under the 2 guides.
7. Reassemble the filters ( B) and ( C).
8. Put back the filter ( B) in the flat filter
( A ). Turn it clockwise until it locks.
CAUTION!
An incorrect position of the
filters can cause bad
washing results and damage
to the appliance.10.2  Cleaning the spray arms
Do not remove the spray arms. If the
holes in the spray arms are clogged,
remove remaining parts of soil with a thin
pointed object.
10.3  External cleaning
• Clean the appliance with a moist soft
cloth.
• Only use neutral detergents.
• Do not use abrasive products, abrasive cleaning pads or solvents.
10.4  Internal cleaning
• Carefully clean the appliance,
including the rubber gasket of the
door, with a soft damp cloth.
www.aeg.com14        
						

							• If you regularly use short durationprogrammes, these can leave
deposits of grease and limescale
inside the appliance. To prevent this,
we recommend to run long duration
programmes at least 2 times per month.• To maintain the performance of your appliance at its best, we recommend
to use monthly a specific cleaning
product for dishwashers. Follow
carefully the instructions on the
packaging of the product.11.  TROUBLESHOOTINGIf the appliance does not start or it stops
during operation, before you contact an Authorised Service Centre, check if youcan solve the problem by yourself with
the help of the information in the table.WARNING!
Repairs not properly done
may result in serious risk to
the safety of the user. Any
repairs must be performed
by qualified personnel.With some problems the end indicator flashes intermittently indicating a
malfunction.
The majority of problems that can
occur can be solved without the need
to contact an Authorised Service
Centre.Problem and alarm codePossible cause and solutionYou cannot activate the appliance.• Make sure that the mains plug is connected to
the mains socket.
• Make sure that there is no damaged fuse in the fuse box.The programme does not start.• Make sure that the appliance door is closed.• If the delay start is set, cancel the setting or wait for the end of the countdown.
• The appliance has started the procedure to re- charge the resin inside the water softener. The
duration of the procedure is approximately 5
minutes.The appliance does not fill with water.
• The end indicator flashes 1 time in- termittently.
• Acoustic signal sounds 1 time in- termittently.• Make sure that the water tap is open.
• Make sure that the pressure of the water sup- ply is not too low. For this information, contact
your local water authority.
• Make sure that the water tap is not clogged.
• Make sure that the filter in the inlet hose is not clogged.
• Make sure that the inlet hose has no kinks or bends.ENGLISH15  
						

							Problem and alarm codePossible cause and solutionThe appliance does not drain the wa-
ter.
• The end indicator flashes 2 times intermittently.
• Acoustic signal sounds 2 times in- termittently.• Make sure that the sink spigot is not clogged.
• Make sure that the drain hose has no kinks or bends.The anti-flood device is on.
• The end indicator flashes 3 times intermittently.
• Acoustic signal sounds 3 times in- termittently.• Close the water tap and contact an Authorised Service Centre.The appliance stops and starts more
times during operation.• It is normal. It provides optimal cleaning re- sults and energy savings.The program lasts too long.• If the delayed start option is set, cancel the de- lay setting or wait for the end of the count-
down.Small leak from the appliance door.• The appliance is not level. Loosen or tighten the adjustable feet (if applicable).
• The appliance door is not centred on the tub. Adjust the rear foot (if applicable).The appliance door is difficult to
close.• The appliance is not level. Loosen or tighten the adjustable feet (if applicable).
• Parts of the tableware are protruding from the baskets.Rattling/knocking sounds from inside
the appliance.• The tableware is not properly arranged in the baskets. Refer to basket loading leaflet.
• Make sure that the spray arms can rotate free- ly.The appliance trips the circuit-beaker.• The amperage is insufficient to supply simulta- neously all the appliances in use. Check thesocket amperage and the capacity of the me-ter or turn off one of the appliances in use.
• Internal electrical fault of the appliance. Con- tact an Authorised Service Centre.Refer to  "Before first use" , 
"Daily use" , or "Hints and
tips"  for other possible
causes.
Once you have checked the appliance,
deactivate and activate the appliance. If
the problem occurs again, contact an
Authorised Service Centre.
For alarm codes not described in the
table, contact an Authorised Service
Centre.www.aeg.com16  
						

							11.1 The washing and drying results are not satisfactoryProblemPossible cause and solutionPoor washing results.• Refer to  "Daily use" , "Hints and tips"  and basket
loading leaflet.
• Use more intensive washing programs.Poor drying results.• Tableware has been left for too long inside a closed appliance.
• There is no rinse aid or the dosage of rinse aid is not enough. Set the rinse aid dispenser to a higher level.
• Plastic items may need to be towel dried.There are whitish streaks or
bluish layers on glasses and
dishes.• The release quantity of rinse aid is too much. Adjust the rinse aid selector to a lower position.
• The quantity of detergent is too much.There are stains and dry water
drops on glasses and dishes.• The released quantity of rinse aid is not sufficient. Ad- just the rinse aid selector to a higher position.
• The quality of the rinse aid can be the cause.The dishes are wet.• The programme does not have a drying phase or has a drying phase with low temperature.
• The rinse aid dispenser is empty.
• The quality of the rinse aid can be the cause.The interior of the appliance is
wet.• This is not a defect of the appliance. it is caused by the humidity in the air that condenses on the walls.Unusual foam during washing.• Use the detergent for dishwashers only.
• There is a leak in the rinse aid dispenser. Contact an Authorised Service Centre.Traces of rust on cutlery.• There is too much salt in the water used for washing. Refer to  "The water softener" .
• Silver and stainless steel cutlery were placed together. Avoid to put silver and stainless steel items close to-
gether.There are residues of deter-
gent in the dispenser at the
end of the program.• The detergent tablet got stuck in the dispenser and therefore was not completely washed away by water.
• Water cannot wash away the detergent from the dis- penser. Make sure that the spray arm is not blocked orclogged.
• Make sure that items in the baskets do not impede the lid of the detergent dispenser from opening.Odours inside the appliance.• Refer to  "Internal cleaning" .Limescale deposits on the ta-
bleware, on the tub and on
the inside of the door.• Refer to  "The water softener" .ENGLISH17 
						

							ProblemPossible cause and solutionDull, discoloured or chipped
tableware.• Make sure that only dishwasher-safe items are washed in the appliance.
• Load and unload the basket carefully. Refer to basket loading leaflet.
• Place delicate items in the upper basket.Refer to  "Before first use" , 
"Daily use"  or "Hints and
tips"  for other possible
causes.12.  TECHNICAL INFORMATIONDimensionsWidth / height / depth (mm)596 / 818-898 / 555Electrical connection 1)Voltage (V)220 - 240Frequency (Hz)50Water supply pressureMin. / max. bar (MPa)0.5 (0.05) / 8 (0.8)Water supplyCold water or hot water 2)max 60 °CCapacityPlace settings13Power consumptionLeft-on mode (W)0.50Power consumptionOff-mode (W)0.501) 
Refer to the rating plate for other values.
2)  If the hot water comes from alternative source of energy, (e.g. solar panels, aeolian energy), use the
hot water supply to decrease energy consumption.13.  ENVIRONMENT CONCERNSRecycle the materials with the symbol .
Put the packaging in applicable
containers to recycle it. Help protect the
environment and human health and to recycle waste of electrical and electronic
appliances. Do not dispose appliancesmarked with the symbol  with the
household waste. Return the product to
your local recycling facility or contact
your municipal office.
*
www.aeg.com18    
						

							ENGLISH19 
						

							www.aeg.com/shop100008660-A-052015