AEG Integrated coffee machine PE4561M User Manual
Have a look at the manual AEG Integrated coffee machine PE4561M User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 513 AEG manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
1415 To remove the tray: 1. Open the service door (fig. 16). 2. Remove the drip tray and the waste coffee container (fig. 17). 3. Clean the drip tray and waste coffee container (A4). 4. 4. Replace the drip tray and waste coffee container (A4). 5. Close the service door. Cleaning the water tank 1. Clean the water tank (A12) regularly (about once a month) with a damp cloth and a little mild washing up liquid. 2. Remove all traces of washing up liquid. Cleaning the spouts 1. Clean the nozzles periodically using a sponge (fig. 28). 2. Check regularly that the holes in the coffee spout are not blocked. If necessary, remove coffee deposits with a toothpick (fig. 26). Cleaning the pre-ground coffee funnel • Check regularly (about once a month) that the pre-ground coffee funnel is not blocked (fig. 21). Danger! Before performing any cleaning operations, the machine must be turned off by pressing the main switch (A23) and unplugged from the mains power supply. Never immerse the coffee maker in water. Cleaning the inside of the coffee maker 1. Check regularly (about once a week) that the inside of the appliance is not dirty. If necessary, remove coffee deposits with a sponge. 2. Remove the residues with a vacuum cleaner (fig. 29). Cleaning the brewing unit The brewing unit must be cleaned at least once a month. Important! The brewing unit (A5) must not be re- moved when the appliance is on. Do not use force to remove the brewing unit. 1. Make sure the machine is correctly turned off (see “Turning the appliance off ”). 2. Open the service door (fig. 16). 3. Remove the drip tray and waste coffee container (fig. 17); 4. Press the two red release buttons inwards and at the same time pull the brewing unit outwards (fig. 30). Important! Do not use washing up liquid to clean the brewing unit. It would remove the lubricant applied to the inside of the piston. 5. Soak the brewing unit in water for about 5 minutes, then rinse. 6. After cleaning, replace the brewing unit (A5) by sliding it onto the internal support and pin at the bottom, then push the PUSH symbol fully in until it clicks into place. N.B.: If the brewing unit is difficult to insert, you must first adapt it to the right dimensions by pressing it forcefully from the bottom and top as shown in the figure. 7. Once inserted, make sure the two red buttons have snapped out. 8. Replace the drip tray and waste coffee container. 9. Close the service door. Support Pin EN
1617 Cleaning the coffee jug Clean the jug with a damp cloth and mild washing up liquid. N.B.: To avoid damaging the appearance of the jug, do not wash in a dishwasher. CHANGING AND SETTING MENU PARAMETERS When the appliance is ready, you can use the internal menu to modify the following parameters and functions: • Choose language • Rinsing • Shut-off time • Set clock • Start time • Auto-start • Temperature • Water hardness • Program coffee • Program jug • Program water • Descale • Reset to default • Statistics • Buzzer • Contrast Setting the language To change the language on the display, proceed as follows: • Press the icon (B2) to enter the menu. “CHOOSE LAN- GUAGE” is displayed. • Press the OK icon (B9). • Press the icons (B7) and (B8) until the required lan- guage is displayed. • Press the OK icon (B9) to confirm. • Press the ESC icon (B6) to exit the menu. N.B.: If you choose the wrong language, you can access the menu directly to modify the parameter. • Press the icon (B2) for at least 7 seconds until the appliance displays the various languages. • Choose the required language as described in the section “Using the appliance for the first time”. Rinsing This function enables you to obtain hotter coffee. Proceed as follows: • When you turn the appliance on, if you want to make a small cup of coffee (less than 60 cc), preheat the cup by rinsing it with hot water. • If on the other hand more than 2/3 minutes have passed since the last coffee was made, before requesting another coffee, you must preheat the brewing unit by first pressing the icon (B2) to enter the menu then the icons (B7) and (B8) to select the “RINSING” function. Press the OK icon (B9). “RINSING... PLEASE CONFIRM” is displayed. Press the OK icon (B9) again. Deliver the water into the underlying drip tray or alterna- tively use this water to fill (and then empty) the cup to be used for the coffee to preheat it. Changing the length of time the appliance remains on The appliance is set by default to go off automatically 30 minutes after the last coffee has been made. To change this interval (max. 120 min), proceed as follows: • Press the icon (B2) to enter the menu and then the icons (B7) and (B8) until “SHUT-OFF TIME” is dis- played. • Press the OK icon (B9) to confirm. • Press the icons (B7) and (B8) to set the time after which the appliance will go off (after 1/2 hour, 1 hour, 2 hours). • Press the OK icon (B9) to confirm. • Press the icon (B6) to exit. Setting the clock • Press the icon (B2) to enter the menu and then the icons (B7) and (B8) until “SET CLOCK” is displayed. • Press the OK icon (B9). • Use the icons (B7) and (B8) to set the hour, then press the OK icon (B9) to confirm. • Use the icons (B7) and (B8) to set the minutes, then press the OK icon (B9) to confirm. • Press the ESC icon (B6) to exit the menu. Setting auto-start time This function programmes the time the machine will come on automatically. • Make sure the clock on the appliance has been set. • Press the icon (B2) to enter the menu and then the EN
1617 icons (B7) and (B8) until “START TIME” is displayed. • Press the OK icon (B9). • Use the icons (B7) and (B8) to set the auto-start time, then press the OK icon (B9) to confirm. • Use the icons (B7) and (B8) to set the minutes, then press the OK icon (B9) to confirm. • Press the e icons (B7) and (B8) to activate the au- to-start function until “AUTO START” is displayed. • Press the OK icon (B9) to confirm. “AUTO START PLEASE CONFIRM” is displayed. Press the OK icon (B9). The symbol appears on the display. • Press the icon (B6) to exit the menu. • To disable auto-start, press the icon (B2), then the icons (B7) and (B8) until “AUTO START” is displayed. Press the OK icon (B9). “PLEASE CONFIRM” is displayed . Press ESC (B6) to disable, the symbol disappears. Changing coffee temperature To change coffee temperature, proceed as follows: • Press the icon (B2) to enter the menu and then the icons (B7) and (B8) until “TEMPERATURE” is dis- played. • Press the OK icon (B9). • Press the icons (B7) and (B8) to select the required coffee temperature from low, medium and high. • Press the OK icon (B9) to confirm the temperature selected. • Press the ESC icon (B6) to exit the menu. Setting water hardness The operating period can be extended if required, making desca- ling less frequent by programming the machine on the basis of the real lime content in the water used. Proceed as follows: • remove the “Total Hardness Test” strip (attached to page 2) from its packaging then dip it fully in the water for a few seconds, Then remove and wait about 30 seconds (until it changes colour and forms red squares). • turn the appliance on by pressing the ON/OFF/stand-by button (A7). • Press the icon (B2) to enter the menu and then the icons (B7) and (B8) until “WATER HARDNESS” is dis- played. • Press the OK icon (B9). • Press the icons (B7) and (B8) until the number co- incides with the number of red squares on the test strip (for example, if there are 3 red squares on the test strip, select the message “WATER HARDNESS 3” . • Press the OK icon (B9) to confirm. The coffee maker is now programmed to provide the des- cale warning when actually necessary. Programming coffee For instructions on programming coffee, see the “CHANGING THE QUANTITY OF COFFEE IN THE CUP” section. Programming the jug For instructions on programming the jug, see the section “ CHANGING JUG FUNCTION PARAMETERS”. Programming water For instructions, see the “CHANGING THE QUANTITY OF HOT WA- TER” section. Descaling Important! Descaler contains acids. Respect the safety warnings provided by the manufacturer and given on the descaler pack. N.B.: Use the descaler recommended by the manufac- turer only. Use of other descalers invalidates the guarantee. Failure to descale the appliance as described also invalidates the guarantee. When “PLEASE DESCALE !” is displayed, the machine requires descaling. Proceed as follows: • make sure the machine is ready; • Press the icon (B2) to enter the menu and then the icons (B7) and (B8) until “DESCALE” is displayed. • Premere l’icona OK (B9) e la macchina visualizza il messag- gio “DECALCIFICAZIONE CONFERMARE”. • Press the OK icon (B9) and the appliance displays “DESCALE PLEASE CONFIRM”. • Press the OK icon (B9). The message “ADD DESCALER PLEASE CONFIRM” is displayed. • Empty the tank of water, pour the contents of the descaler bottle into the tank respecting the instructions given on the descaler pack, then add water. Position a container with a capacity of 2 litres under the hot water spout. EN
1819 • Press the OK icon (B9). Descaler flows out of the hot water spout into the container below. The appliance displays: “DESCALING”. • The descale programme automatically performs a series of deliveries and pauses. • After about 30 minutes “DESCALE COMPLETE PLEASE CON- FIRM” is displayed. • Press the OK icon (B9). “RINSING FILL TANK” is displayed. • Empty the water tank, rinse to eliminate descaler residues, then fill with clean water. • Replace the tank full of clean water. “RINSING PLEASE CONFIRM” is displayed again. • Press the OK icon (B9) again. Hot water flows out of the spout into the container below and “RINSING” is displayed. • Wait until “RINSING COMPLETE PLEASE CONFIRM” is dis- played. • Press the OK icon (B9). “DESCALE COMPLETE” is displayed, then “FILL TANK!”. Fill the tank again with clean water. • The descale programme is now terminated and the appli- ance is ready to make coffee again. NOTE: If descaling is interrupted before completion, the process must be begun again from the beginning. Important! FAILURE TO DESCALE THE APPLIANCE REG- ULARLY INVALIDATES THE GUARANTEE. Resetting default values (reset) If you change the original values, the default values can be reset as follows: • Press the icon (B2) to enter the menu and then the icons (B7) and (B8) until “RESET TO DEFAULT” is dis- played. • Press the OK icon (B9) and the appliance displays “RESET TO DEFAULT PLEASE CONFIRM”. • press the OK icon (B9) to reset the default values; Statistics This displays statistics relating to the machine. To display, pro- ceed as follows: • Press the icon (B2) to enter the menu and then the icons (B7) and (B8) until “STATISTICS” is displayed. • Press the OK icon (B9). • Press the icons (B7) and (B8) to verify: • How many coffees and cappuccinos have been made. • How many times the machine has been descale • The total number of litres of water delivered. • Press the ESC icon (B6) once to exit the function or twice to exit the menu. Buzzer This activates or deactivates the buzzer emitted by the machine each time an icon is pressed or an accessory is inserted/removed. N.B.: The buzzer is active by default. • Press the icon (B2) to enter the menu and then the icons (B7) and (B8) until “BUZZER” is displayed. • Press the OK icon (B9). “BUZZER PLEASE CONFIRM” is dis- played. • Press the ESC icon (B6) to disable or the OK icon (B9) to enable the buzzer. • Press the ESC icon (B6) to exit the menu. Adjusting contrast To increase or reduce the contrast of the display, proceed as fol- lows: • Press the icon (B2) to enter the menu and then the icons (B7) and (B8) until “CONTRAST” is displayed. • Press the OK icon (B9). • Press the icons (B7) and (B8) until the required dis- play contrast is reached. The progressive bar indicates the level of contrast selected. • Press the OK icon (B9) to confirm. • Press the ESC (B6) icon (B6) once to exit the function or twice to exit the menu. TURNING THE APPLIANCE OFF Each time the appliance is turned off, it performs an automatic rinse cycle which cannot be interrupted. Danger of burns! During rinsing, a little hot water flows from the coffee spouts. Avoid contact with splashes of water. To turn the appliance off, press the ON/OFF button (A7). The appliance performs the rinse cycle then goes off. N.B.: If the appliance is not used for an extended peri- od, place the main switch on the back of the appliance in the 0 position (A23). EN
1819 TECHNICAL SPECIFICATION Voltage: 220-240 V~ 50/60 Hz max. 10A Absorbed power: 1350W Pressure: 15 bars Water tank capacity: 1.8 litres Size LxHxD: 594x 378/460x398 Weight: 23/24 kg The appliance complies with the following EC directives: • Low Voltage Directive 2006/95/EC and subsequent amend- ments; • EMC Directive 2004/108/EC and subsequent amendments • EC Regulation 1275/2008 for standby Materials and accessories coming into contact with food conform to European regulation (EC) no. 1935/2004. EN
2021 DISPLAYED MESSAGEPOSSIBLE CAUSE REMEDY FILL TANK! The water tank is empty or positioned incorrectly.Fill the tank with water and/or insert it cor-rectly, pushing it as far as it will go. GROUND TOO FINE ADJUST MILL AND (alternating with)PRESS OK The grinding is too fine and the coffee is delivered too slowly. The machine cannot make coffee as there is air in the hydraulic circuitPossible cause: the filter has not been installed correctly. Turn the grinding adjustment knob one click clockwise towards “7”.Make sure the filter (A26) is properly instal-led and that the installation has been carried out correctly. GROUND TOO FINE ADJUST MILL AND(alternating with)PRESS OK(then)FILL TANK! The tank has been removed during delivery. Insert the tank and press the OK icon (B9). “HOT WATER PRESS OK” is displayed.Press the OK icon (B9) again. The appliance is once again ready for use. EMPTY WASTE COFFEE CONTAINER The waste coffee container (A4) is too full or more than 3 days have passed since you last made coffee (this gua-rantees correct hygiene of the machi-ne). Empty the waste coffee container and clean, then replace. Important: when removing the drip tray, the waste coffee container MUST be emptied, even if it is not completely full.If this is not done, when you make the next coffees, the waste coffee container may fill up more than expected and clog the ma-chine. INSERT WASTE COFFEE CONTAINERAfter cleaning, the waste coffee con-tainer has not been replaced.Open the service door and insert the waste coffee container. ADD PRE-GROUND COFFEEThe “pre-ground coffee” function has been selected without placing any pre-ground coffee in the funnel.The funnel (A21) is blocked. Extract the appliance and place pre-ground coffee in the funnel. Empty the funnel with the help of a knife as described in the section “Cleaning the pre-ground coffee funnel”. PLEASE DESCALE! The machine must be descaled. The descaling procedure described in the “Descaling” section needs to be performed as soon as possible. LESS COFFEE Too much coffee has been used.Select a milder taste or reduce the quantity of pre-ground coffee, then make the coffee again. FILL BEAN CONTAINERThe coffee beans have run out.Fill bean container INSERT BREWING UNITThe brewing unit has not been repla-ced after cleaning. Insert the brewing unit as described in the section “Cleaning the brewing unit”. CLOSE DOOR The service door is openClose the service door. DISPLAYED MESSAGES EN
2021 TROUBLESHOOTINGBelow is a list of some of the possible malfunctions. If the problem cannot be resolved as described, contact Custo-mer Services. PROBLEMPOSSIBLE CAUSE REMEDY The coffee is not hot The cups were not preheated. The brewing unit has cooled down because 2/3 minutes have elapsed since the last coffee was made. The temperature set is too low. Warm the cups by rinsing them with hot water. Before making coffee, preheat the brewing unit by selecting the RINSING function in the menu. Change the set temperature (see paragraph “Chan-ging coffee temperature”). The coffee is not creamy enough The coffee is ground too coarsely. Wrong type of coffee Turn the grinding adjustment knob one click an-ticlockwise towards “1” while the coffee mill is in operation (fig. 11).Use a type of coffee for espresso coffee makers. The coffee is delivered too slowly or a drop at a time. The coffee is ground too finely.Turn the grinding adjustment knob one click clockwise towards “7” while the coffee mill is in ope-ration (fig. 11). Continue one click at a time until coffee delivery is satisfactory. The effect is only visible after delivering two coffees. The coffee is delivered too quickly.The coffee is ground too coarsely.Turn the grinding adjustment knob one click an-ticlockwise towards “1” while the coffee mill is in operation (fig. 11). Avoid turning the grinding adjustment knob exces-sively otherwise when you select 2 cups, the coffee may be delivered a drop at a time.The effect is only visible after delivering two coffees. Coffee does not come out of one of the spouts.The spouts are blocked.Clean the spouts with a toothpick (fig. 23). The coffee does not come out of the spouts, but from around the service door (A2). The holes in the spouts are clogged with dry coffee dust.The coffee guide (A3) inside the service door is blocked and cannot swing. If necessary, remove coffee deposits with a toothpick, sponge or stiff bristled kitchen brush (fig. 23). Thoroughly clean the coffee guide (A3), particularly near the hinges. Water comes out of the spouts in-stead of coffee. The pre-ground coffee may be blo-cked in the funnel (A21).Clean the funnel (A21) with a wooden or plastic fork, clean the inside of the machine. DISPLAYED MESSAGEPOSSIBLE CAUSE REMEDY GENERAL ALARMThe inside of the appliance is very dirty.Clean the inside of the appliance thoroughly, as described in the section “Cleaning and maintenance”. If the message is still displayed after clea-ning, contact a customer services. EN