AEG Induction hob HKP67420FB User Manual

To deactivate the function: set the
cooking zone with 
 and touch . The
remaining time counts back to 00. The
indicator of the cooking zone goes out.
When the time comes to an
end, the sound operates and
00 flashes. The cooking zone
deactivates.
To stop the sound:  touch .
CountUp Timer (The count up timer)
You can use this function to monitor how
long the cooking zone operates.
To set the cooking zone:  touch 
again and again until the indicator of a
necessary cooking zone comes on.
To activate the...

4.11 OffSound Control
(Deactivating and activating
the sounds)
Deactivate the hob. Touch 
 for 3
seconds. The display comes on and goes
out. Touch 
 for 3 seconds.  or 
comes on. Touch  of the timer to
choose one of the following:
•
 - the sounds are off
•
 - the sounds are on
To confirm your selection wait until the hob deactivates automatically.
When the function is set to 
 you can
hear the sounds only when:
• you touch 
• Minute Minder comes down
• Count Down Timer comes down
• you put something on...

When you switch between
the modes the heat setting
is set back to  0.
Diameter and position of the
cookware
Choose the mode applicable to the size
and the shape of the cookware. The
cookware should cover the selected area
as much as possible. Place the cookware
centrally on the selected area!
Place the cookware with the bottom
diameter smaller than 160 mm centrally
on a single section.
Place the cookware with the bottom
diameter larger then 160 mm centrally
between two sections.
5.2  FlexiBridge...

left control bar for the smaller zone.
Correct cookware position:
To use this mode you have to place the cookware on the three connected
sections. If you use cookware smaller
than two sections the display shows 
and after 2 minutes the zone switches off.
Incorrect cookware position:
5.4  FlexiBridge Max Bridge
mode
To activate the mode press  until you
see the correct mode indicator 
. This
mode connects all sections into one
cooking zone. To set the heat setting use
any of the two control bars on the...

with the position. You can place the
cookware in the front, middle or rear
position. If you place the cookware in the
front you get the highest heat setting. To
decrease it, move the cookware to
middle or rear position.Use only one pot when you
operate the function.
General information:
• 160 mm is the minimum bottom diameter of the cookware for thisfunction.
• Heat setting display for the left rear control bar shows the position of the
cookware on the induction cooking
area. Front 
, middle , rear
.
•...

Use the induction cooking
zones with correct cookware.
Cookware material
• correct:  cast iron, steel, enamelled
steel, stainless steel, the bottom made of multi-layer (with correct mark
from a manufacturer).
• not correct:  aluminium, copper,
brass, glass, ceramic, porcelain.
Cookware is correct for an induction
hob if:
• some water boils very quickly on a zone set to the highest heat setting.
• a magnet pulls on to the bottom of the cookware.
The printing on the flexible
induction cooking area may...

Heat settingUse to:Time
(min)Hints3 - 5Simmer rice and milkbased
dishes, heating up ready-
cooked meals.25 - 50Add the minimum twice as
much liquid as rice, mix milk
dishes part procedure
through.5 - 7Steam vegetables, fish, meat.20 - 45Add some tablespoons of liq-
uid.7 - 9Steam potatoes.20 - 60Use max. ¼ l water for 750 g of
potatoes.7 - 9Cook larger quantities of food,
stews and soups.60 - 150Up to 3 l liquid plus ingredi-
ents.9 - 12Gentle fry: escalope, veal cor-
don bleu, cutlets, rissoles,...

8. TROUBLESHOOTINGWARNING!
Refer to Safety chapters.8.1  What to do if...ProblemPossible causeRemedyYou cannot activate or oper-
ate the hob.The hob is not connected to
an electrical supply or it is
connected incorrectly.Check if the hob is correctly
connected to the electrical
supply. Refer to the connec-
tion diagram. The fuse is blown.Make sure that the fuse is
the cause of the malfunction.
If the fuse is blown again
and again, contact a quali-
fied electrician.  Activate the hob again and
set the...

ProblemPossible causeRemedyThe sensor fields become
hot.The cookware is too large or
you put it too near to the
controls.Put large cookware on the
rear zones if possible.There is no signal when you
touch the panel sensor
fields.The signals are deactivated.Activate the signals.
Refer to "Daily use" chapter.The flexible induction cook-
ing area does not heat up
the cookware.The cookware is in the
wrong position on the flexi-
ble induction cooking area.Place the cookware in the
correct position on...

ProblemPossible causeRemedy FlexiBridge function oper-
ates. One or more sections
of the function mode which
operates are not covered by
the cookware.Place the cookware on the
correct number of sections
of the function mode which
operates or change the func-
tion mode.
Refer to "Flexible induction
cooking area" chapter. PowerSlide function oper-
ates. Two pots are placed on
the flexible induction cook-
ing area.Use only one pot.
Refer to "Flexible induction
cooking area" chapter. and a...