AEG Induction hob HKP65410FB User Manual

							comes on. Touch  of the timer to
choose one of the following:
•
 - the sounds are off
•
 - the sounds are on
To confirm your selection wait until the hob deactivates automatically.
When the function is set to 
 you can
hear the sounds only when:
• you touch 
• Minute Minder comes down
• Count Down Timer comes down
• you put something on the control panel.
4.11  Power management
function
• Cooking zones are grouped according to the location and number
of the phases in the hob. See the illustration.
• Each phase has a maximum electricity loading of 3700 W.
• The function divides the power between cooking zones connected to
the same phase.
• The function activates when the total electricity loading of the cookingzones connected to a single phase
exceeds 3700 W.
• The function decreases the power to the other cooking zones connected to
the same phase.
• The heat setting display of the reduced zones changes between twolevels.
4.12  Hob²Hood
It is an advanced automatic function
which connects the hob to a special
hood. Both the hob and the hood have
an infra — red signal communicator.
Speed of the fan is defined automatically on basis of mode setting and
temperature of the hottest cookware on
the hob. You can also operate the fan
from the hob manually.For most of the hoods the
remote system is originally
deactivated. Activate it
before you use the function.
For more information refer
to hood user manual.Operating the function automatically
To operate the function automatically set
the automatic mode to H1 – H6. The hob is originally set to H5. The hood reactswhenever you operate the hob. The hob
recognizes temperature of the cookware
automatically and adjusts the speed of
the fan.
Automatic modes Auto-
matic
lightBoiling1)Frying2)Mode H0OffOffOffMode H1OnOffOffMode
H2 3)OnFan
speed 1Fan
speed 1Mode H3OnOffFan
speed 1Mode H4OnFan
speed 1Fan
speed 1Mode H5OnFan
speed 1Fan
speed 2Mode H6OnFan
speed 2Fan
speed 31)  The hob detects the boiling process and acti-
vates fan speed in accordance with automatic mode.
2)  The hob detects the frying process and acti-
vates fan speed in accordance with automatic mode.
3)  This mode activates the fan and the light and
does not rely on the temperature.Changing the automatic mode
1. Deactivate the appliance.
ENGLISH11        
						

							2.Touch  for 3 seconds. The display
comes on and goes off
3. Touch 
 for 3 seconds.
4. Touch 
 a few times until  comes
on.
5. Touch 
 of the Timer to select an
automatic mode.
To operate the hood directly
on the hood panel
deactivate the automatic
mode of the function.When you finish cooking and
deactivate the hob, the
hood fan may still operate
for a certain period of time.
After that time the system
deactivates the fan
automatically and prevents
you from accidental
activation of the fan for the
next 30 seconds.Operating the fan speed manually
You can also operate the function
manually. To do that touch 
 when the
hob is active. This deactivates automatic
operation of the function and allows you
to change the fan speed manually. When
you press 
 you raise the fan speed by
one. When you reach an intensive level
and press 
 again you will set fan speed
to 0 which deactivates the hood fan. To start the fan again with fan speed 1 touch
.
To activate automatic
operation of the function,
deactivate the hob and
activate it again.Activating the light
You can set the hob to activate the light
automatically whenever you activate the hob. To do so set the automatic mode to
H1 – H6.
The light on the hood
deactivates 2 minutes after
deactivating the hob.5.  FLEXIBLE INDUCTION COOKING AREAWARNING!
Refer to Safety chapters.5.1  FlexiBridge function
The flexible induction cooking area
consists of four sections. The sections
can be combined into two cooking zones
with different size, or into one large
cooking area. You choose the
combination of the sections by choosing
the mode applicable to the size of the
cookware you want to use. There are
three modes: Standard (activated
automatically when you activate the
hob), Big Bridge and Max Bridge.
To set the heat setting use
two left side control bars.
Switching between the modes
To switch between the modes use sensor
field: 
.
When you switch between
the modes the heat setting
is set back to  0.
Diameter and position of the
cookware
Choose the mode applicable to the size
and the shape of the cookware. The
cookware should cover the selected area
as much as possible. Place the cookware
centrally on the selected area!
www.aeg.com12                   
						

							Place the cookware with the bottom
diameter smaller than 160 mm centrally
on a single section.
Place the cookware with the bottom
diameter larger then 160 mm centrally
between two sections.
5.2  FlexiBridge Standard
mode
This mode is active when you activate
the hob. It connects the sections into two
separate cooking zones. You can set the
heat setting for each zone separately. Use two left side control bars.
Correct cookware position:
Incorrect cookware position:
5.3  FlexiBridge Big Bridge
mode
To activate the mode press  until you
see the correct mode indicator. This
mode connects three rear sections into
one cooking zone. The one front section is not connected and operates as a
separate cooking zone. You can set the heat setting for each zone separately.
Use two left side control bars.
Correct cookware position:
To use this mode you have to place the cookware on the three connected
sections. If you use cookware smaller
than two sections the display shows 
and after 2 minutes the zone switches off.
ENGLISH13100-160mm > 160 mm        
						

							Incorrect cookware position:
5.4 FlexiBridge Max Bridge
mode
To activate the mode press  until you
see the correct mode indicator. This
mode connects all sections into one
cooking zone. To set the heat setting use
one of the left side control bars.
Correct cookware position:
To use this mode you have to place the cookware on the four connected
sections. If you use cookware smaller
than three sections the display shows 
and after 2 minutes the zone switches off.
Incorrect cookware position:
5.5  PowerSlide function
This function allows you to adjust the
temperature by moving the cookware to
a different position on the induction
cooking area.
The function divides the induction
cooking area into three areas with
different heat settings. The hob senses
the position of the cookware and sets the
heat setting corresponding with the
position. You can place the cookware in
the front, middle or rear position. If you
place the cookware in the front you get
the highest heat setting. You can
decrease the heat setting by moving the
cookware in the middle or to the rear
position.
Use only one pot when you
operate the function.www.aeg.com14          
						

							General information:
• 160 mm is the minimum bottom diameter of the cookware for thisfunction.
• Heat setting display for the left rear control bar shows the position of the
cookware on the induction cooking
area. Front 
, middle , rear
.
• Heat setting display for the left front control bar shows the heat setting.  To
change the heat setting use left front control bar.
• When you activate the function for the
first time you will get heat setting 
for the front position,  for the
middle position and  for the rear
position.
You can change the heat settings for
each position separately. The hob will remember your heat settings nexttime you activate the function.
Activating the function
To activate the function place the
cookware in the correct position on the
cooking area. Touch 
. The indicator
above the symbol comes on. If you do not place the cookware on the cooking
area 
 comes on and after 2 minutes
the flexible induction cooking area is set
to 
.
Deactivating the function
To deactivate the function touch 
 or
set the heat setting to 
. The indicator
above the symbol 
 goes off.
6.  HINTS AND TIPSWARNING!
Refer to Safety chapters.6.1  CookwareFor induction cooking zones
a strong electro-magnetic
field creates the heat in the
cookware very quickly.Use the induction cooking
zones with correct cookware.
Cookware material
• correct:  cast iron, steel, enamelled
steel, stainless steel, the bottom made of multi-layer (with correct mark
from a manufacturer).
• not correct:  aluminium, copper,
brass, glass, ceramic, porcelain.
Cookware is correct for an induction
hob if:
• some water boils very quickly on a zone set to the highest heat setting.
• a magnet pulls on to the bottom of the cookware.ENGLISH15                   
						

							The printing on the flexible
induction cooking area may
become dirty or change
colour from sliding the
cookware. You can clean the
area in a standard way.The bottom of the cookware
must be as thick and flat as
possible.
Cookware dimensions
Induction cooking zones adapt to the dimension of the bottom of the
cookware automatically to some limit.
The cooking zone efficiency is related to
the diameter of the cookware. The
cookware with a smaller diameter than
the minimum receives only a part of the power generated by the cooking zone.
Refer to “Technical
information” chapter.6.2  The noises during
operation
If you can hear:
• crack noise: cookware is made of different materials (sandwich
construction).
• whistle sound: you use the cooking
zone with high power level and the
cookware is made of different
materials (sandwich construction).
• humming: you use high power level. • clicking: electric switching occurs.
• hissing, buzzing: the fan operates.
The noises are normal and do not refer
to hob malfunction.6.3  Öko Timer (Eco Timer)
To save energy, the heater of the
cooking zone deactivates before the count down timer sounds. The difference
in the operation time depends on theheat setting level and the length of thecooking operation.
6.4  Examples of cooking
applications
The relation between the heat setting and the cooking zone consumption of
power is not linear. When you increase the heat setting, it is not proportional to
the increase of the cooking zone
consumption of power. It means that the cooking zone with the medium heat
setting uses less than a half of its power.
The data in the table is for
guidance only.Heat settingUse to:Time
(min)Hints - 1Keep cooked food warm.as nec-
essaryPut a lid on the cookware.1 - 3Hollandaise sauce, melt: but-
ter, chocolate, gelatine.5 - 25Mix from time to time.1 - 3Solidify: fluffy omelettes,
baked eggs.10 - 40Cook with a lid on.3 - 5Simmer rice and milkbased
dishes, heating up ready-
cooked meals.25 - 50Add the minimum twice as
much liquid as rice, mix milk
dishes part procedure
through.5 - 7Steam vegetables, fish, meat.20 - 45Add some tablespoons of liq-
uid.www.aeg.com16      
						

							Heat settingUse to:Time
(min)Hints7 - 9Steam potatoes.20 - 60Use max. ¼ l water for 750 g of
potatoes.7 - 9Cook larger quantities of food,
stews and soups.60 - 150Up to 3 l liquid plus ingredi-
ents.9 - 12Gentle fry: escalope, veal cor-
don bleu, cutlets, rissoles,
sausages, liver, roux, eggs,
pancakes, doughnuts.as nec-
essaryTurn halfway through.12 - 13Heavy fry, hash browns, loin
steaks, steaks.5 - 15Turn halfway through.14Boil water, cook pasta, sear meat (goulash, pot roast), deep-fry chips.Boil large quantities of water. Power function is activated.6.5  Hints and Tips for
Hob²Hood function
When you operate the hob with the
function:
• Protect the hood panel from direct sunlight.
• Do not spot halogen light on the hood panel.
• Do not cover the hob panel.
• Do not interrupt the signal between the hob and the hood (for example
with a hand or a cookware handle). See the picture.  Hood in the picture
is only exemplary.It may happen that other
remote controlled
appliances may block the
signal. To avoid it do not
operate the remote of the
appliance and the hob at the
same time.
Cooker hoods with the Hob²Hood
function
To find the full range of cooker hoods
which work with this function refer to our
consumer website. The AEG cooker
hoods that work with this function must
have the symbol 
.
ENGLISH17     
						

							7. CARE AND CLEANINGWARNING!
Refer to Safety chapters.7.1  General information
• Clean the hob after each use.
• Always use cookware with clean bottom.
• Scratches or dark stains on the surface have no effect on how the hob
operates.
• Use a special cleaner applicable for the surface of the hob.
• Use a special scraper for the glass.
7.2  Cleaning the hob
•Remove immediately:  melted plastic,
plastic foil, sugar and food with sugar.
If not, the dirt can cause damage to
the hob. Take care to avoid burns. Put
the special scraper on the glass
surface at an acute angle and move the blade on the surface.
• Remove when the hob is sufficiently
cool:  limescale rings, water rings, fat
stains, shiny metallic discoloration.
Clean the hob with a moist cloth and
non-abrasive detergent. After
cleaning, wipe the hob dry with a soft
cloth.
• Remove shiny metallic
discoloration:  use a solution of water
with vinegar and clean the glass
surface with a moist cloth.8.  TROUBLESHOOTINGWARNING!
Refer to Safety chapters.8.1  What to do if...ProblemPossible causeRemedyYou cannot activate or oper-
ate the hob.The hob is not connected to
an electrical supply or it is
connected incorrectly.Check if the hob is correctly
connected to the electrical
supply. Refer to the connec-
tion diagram. The fuse is blown.Make sure that the fuse is
the cause of the malfunction.
If the fuse is blown again
and again, contact a quali-
fied electrician.  Activate the hob again and
set the heat setting in less
than 10 seconds. You touched 2 or more sen-
sor fields at the same time.Touch only one sensor field. There is water or fat stains
on the control panel.Clean the control panel.www.aeg.com18   
						

							ProblemPossible causeRemedyAn acoustic signal sounds
and the hob deactivates.
An acoustic signal sounds
when the hob is deactivated.You put something on one
or more sensor fields.Remove the object from the
sensor fields.The hob deactivates.You put something on the
sensor field 
.
Remove the object from the
sensor field.Residual heat indicator does
not come on. The zone is not hot because
it operated only for a short
time.If the zone operated suffi-
ciently long to be hot, speak
to an Authorised Service
Centre.Hob²Hood function does not
work.You covered the control
panel.Remove the object from the
control panel.Automatic Heat Up function
does not operate.The zone is hot.Let the zone become suffi-
ciently cool. The highest heat setting is
set.The highest heat setting has
the same power as the func-
tion.The heat setting changes
between two levels.Power management function
operates.Refer to "Daily use" chapter.The sensor fields become
hot.The cookware is too large or
you put it too near to the
controls.Put large cookware on the
rear zones if possible.There is no signal when you
touch the panel sensor
fields.The signals are deactivated.Activate the signals.
Refer to "Daily use" chapter.The flexible induction cook-
ing area does not heat up
the cookware.The cookware is in the
wrong position on the flexi-
ble induction cooking area.Place the cookware in the
correct position on the flexi-
ble induction cooking area.
The position of the cook-
ware depends on the activa-
ted function or function
mode.
Refer to "Flexible induction
cooking area" chapter.ENGLISH19  
						

							ProblemPossible causeRemedy The diameter of the bottom
of the cookware is incorrect
for the activated function or
function mode.Use cookware with diameter
applicable to the activated
function or function mode.
Use cookware with diameter
smaller than 160 mm on a
single section of the flexible
induction cooking area.
Refer to "Flexible induction
cooking area" chapter. comes on.Automatic Switch Off oper-
ates.Deactivate the hob and acti-
vate it again. comes on.The Child Safety Device or
the Lock function operates.Refer to "Daily use" chapter. comes on.There is no cookware on the
zone.Put cookware on the zone. The cookware is incorrect.Use the correct cookware.
Refer to “Hints and tips”
chapter. The diameter of the bottom
of the cookware is too small
for the zone.Use cookware with correct
dimensions.
Refer to “Technical informa-
tion” chapter. FlexiBridge function oper-
ates. One or more sections
of the function mode which
operates are not covered by
the cookware.Place the cookware on the
correct number of sections
of the function mode which
operates or change the func-
tion mode.
Refer to "Flexible induction
cooking area" chapter. PowerSlide function oper-
ates. Two pots are placed on
the flexible induction cook-
ing area.Use only one pot.
Refer to "Flexible induction
cooking area" chapter. and a number come on.There is an error in the hob.Disconnect the hob from the
electrical supply for some
time. Disconnect the fuse
from the electrical system of
the house. Connect it again.
If 
 comes on again, speak
to an Authorised Service
Centre.
www.aeg.com20