AEG Freestanding washer dryer L87695NWD User Manual

							5.6.7.8.9. 13.8 Emergency drain
Because of a malfunction, the appliance cannot drain the water.
If this occurs, do steps (1) through (9) of
'Cleaning the drain filter'. If necessary,
clean the pump.
When you drain the water with the
emergency drain procedure, you must
activate the drain system again:1. Put 2 litres of water in the main wash
compartment of the detergent
dispenser.
2. Start the programme to drain the
water.13.9  Frost precautions
If the appliance is installed in an area
where the temperature can be less than 0° C, remove the remaining water fromthe inlet hose and the drain pump.
ENGLISH3112   1
2 1
2  
						

							1.Disconnect the mains plug from the
mains socket.
2. Close the water tap.
3. Put the two ends of the inlet hose in
a container and let the water flow out of the hose.
4. Empty the drain pump. Refer to the
emergency drain procedure.
5. When the drain pump is empty,
install the inlet hose again.WARNING!
Make sure that the
temperature is higher than 0
°C before you use the
appliance again.
The manufacturer is not responsible for damages
caused by low temperatures.14.  TROUBLESHOOTINGWARNING!
Refer to Safety chapters.14.1  Introduction
The appliance does not start or it stops
during operation.
First try to find a solution to the problem
(refer to the table). If the problem
persists, contact the Authorised Service Centre.
With some problems, the acoustic signals operate and the display shows
an alarm code:
•
 - The appliance does not fill with
water properly.
•
 - The appliance does not drain
the water.
• - The appliance door is open or
not closed correctly. Please check the
door!
•
 - The mains supply is unstable.
Wait until the mains supply is stable.
•
 - No communication between
electronic elements of the appliance.
Switch off and switch on again.
•
 - The anti-flood device is on.
Disconnect the appliance and close
the water tap. Contact the Authorised Service Centre.
WARNING!
Deactivate the appliance
before you do the checks.14.2  Possible failuresProblemPossible solutionThe programme does
not start.Make sure that the mains plug is connected to the mains sock-
et. Make sure that the appliance door is closed. Make sure that there is not a damaged fuse in the fuse box. Make sure that the Start/Pause has been pressed. If the delay start is set, cancel the setting or wait for the end of
countdown. Deactivate the Child Lock function if it is on.The appliance does not
fill with water properly.Make sure that the water tap is open.www.aeg.com32          
						

							ProblemPossible solution Make sure that the pressure of the water supply is not too low.
For this information, contact your local water authority. Make sure that the water tap is not clogged.Make sure that the filter of the inlet hose and the filter of the
valve are not clogged. Refer to “Care and cleaning”.Make sure that the inlet hose has no kinks or bends.Make sure that the connection of the water inlet hose is cor-
rect.The appliance does not
fill with water and drain
immediately.Make sure that the drain hose is in the correct position. The
hose may be too low.The appliance does not
drain the water.Make sure that the sink spigot is not clogged. Make sure that the drain hose has no kinks or bends. Make sure that the drain filter is not clogged. Clean the filter, if
necessary. Refer to 'Care and cleaning'. Make sure that the connection of the drain hose is correct. Set the drain programme if you set a programme without drain
phase. Set the drain programme if you set an option which ends with
water in the tub.The spin phase does not
operate or the washing
cycle lasts longer than
usually.Set the spin programme. Make sure that the drain filter is not clogged. Clean the filter, if
necessary. Refer to 'Care and cleaning'. Adjust manually the items in the tub and start the spin phase
again. This problem may be caused by balance problems.There is water on the
floor.Make sure that the couplings of the water hoses are tight and
there is not water leakages. Make sure that the drain hose have no damages. Make sure you use the correct detergent and the correct quan-
tity of it.You cannot open the ap-
pliance door.Make sure that the washing programme is finished.ENGLISH33 
						

							ProblemPossible solution Set the drain or the spin programme if there is water in the
drum.Make sure that the appliance receives electrical power.This problem may be caused by a failure of the appliance.
Contact the Authorised Service Centre. If you need to open
the door, please read carefully «Emergency door opening».The appliance makes an
unusual noise.Make sure the levelling of the appliance is correct. Refer to 'In-
stallation'. Make sure that the packaging and/or the transit bolts are re-
moved. Refer to 'Installation'. Add more laundry in the drum. The load may be too small.The cycle is shorter than
the time displayed.The appliance calculates a new time according to the laundry
load. See the ‘Consumption Values’ chapter.The cycle is longer than
the time displayed.An unbalanced laundry load increases the duration time. This
is a normal behaviour of the appliance.The washing results are
not satisfactory.Increase the detergent quantity or use a different detergent. Use special products to remove the stubborn stains before you
wash the laundry. Make sure that you set the correct temperature. Decrease the laundry load.You cannot set an op-
tion.Make sure that you press only the wanted button(s).The appliance does not
dry or does not dry cor-
rectly.Turn the water tap on.Make sure the drain filter is not clogged.Reduce the laundry load.Make sure you have set the correct cycle. if necessary ,set
again a short drying time.The laundry is full of dif-
ferent colours fluff.The fabrics washed in the previous cycle released fluff of a dif-
ferent colour:
• The drying phase helps to eliminate some fluff.
• Clean the clothes with a fluff remover.
In case of an excessive amount of fluff in the drum run the spe-
cial programme to clean it (refer to “Fluff in the fabrics" for
more details).www.aeg.com34 
						

							After the check, activate the appliance. The programme continues from the point of
interruption.
If the problem occurs again, contact the Authorised Service Centre.
If the display shows other alarm codes. Deactivate and activate the appliance. If the
problem continues, contact the Authorised Service Centre.14.3  Emergency door opening
In case of power failure or functioning failure the appliance door remainslocked. The washing programme
continues when the power is restored. If
the door remains locked in case of
failure, it is possible to open it using the
emergency unlock function.
Before opening the door:CAUTION!
Make sure that the water
temperature is not too
high and the laundry is not
hot. If necessary, wait until
they cool down.CAUTION!
Make sure that the drum is
not rotating. If necessary,
wait until the drum stops
rotating.Make sure that the water
level inside the drum is not
too high. If necessary,
proceed with an
emergency drain (refer to
«Emergency drain» in
«Care and cleaning»
chapter).To open the door, proceed as follows:
1. Press the On/Off button to switch the
appliance off.
2. Disconnect the mains plug from the
mains socket.
3. Open the filter flap.
4. Keep the emergency unlock trigger
pulled downward and, at the same
time, open the appliance door.
5. Take out the laundry and then close
the appliance door.
6. Close the filter flap.
15.  TECHNICAL DATADimensionWidth/ Height/ Depth/
Total depth600 mm/ 850 mm/ 605 mm/ 639 mmElectrical connectionVoltage
Overall power
Fuse
Frequency230-240 V
2200 W
13 A
50 HzLevel of protection against ingress of solid particles
and moisture ensured by the protective cover, ex-
cept where the low voltage equipment has no pro-
tection against moistureIPX4ENGLISH35     
						

							Water supply pressure1)Minimum
Maximum0,5 bar (0,05 MPa)
8 bar (0,8 MPa)Maximum wash loadCotton9 kgMaximum dry loadCotton
Synthetics6 kg
3 kgSpin SpeedMaximum1600 rpm1)  The appliance works correctly if the water pressure is not lower than 0.05 MPa (0.5 bar). If you cannot
connect the water inlet hose to the cold water tap of the primary hydraulic system, connect it to your
domestic cold water storage system. Make sure not to exceed a distance of 5.02 m (16.5 ft) between the
appliance inlet hose and the bottom of the water storage tank.16.  ENVIRONMENTAL CONCERNSRecycle the materials with the symbol .
Put the packaging in applicable
containers to recycle it. Help protect the
environment and human health and to recycle waste of electrical and electronic
appliances. Do not dispose appliancesmarked with the symbol  with the
household waste. Return the product to
your local recycling facility or contact
your municipal office.
*
www.aeg.com36   
						

							ENGLISH37 
						

							www.aeg.com38 
						

							ENGLISH39 
						

							www.aeg.com/shop132950400-A-282015