AEG Freestanding fridge freezer S95900XTM0 User Manual

							To get best performance the carbon air
filter should be changed once every year.
New active air filters can be purchased
from your local dealer.Refer to “Installation of the carbon air
filter” for the instructions.7.  TROUBLESHOOTINGWARNING!
Refer to Safety chapters.7.1  What to do if...ProblemPossible causeSolutionThe appliance does not op-
erate.The appliance is switched
off.Switch on the appliance. The mains plug is not con-
nected to the mains socket
correctly.Connect the mains plug to the
mains socket correctly. There is no voltage in the
mains socket.Connect a different electrical
appliance to the mains socket.
Contact a qualified electrician.The appliance is noisy.The appliance is not sup-
ported properly.Check if the appliance stands
stable.Audible or visual alarm is on.The cabinet has been re-
cently switched on or the
temperature is still too
high.Refer to "Door Open Alarm"or
"High Temperature Alarm".The temperature in the ap-
pliance is too high.Refer to "Door Open Alarm"or
"High Temperature Alarm".The door is left open.Close the door.The temperature in the ap-
pliance is too high.Contact a qualified electrician
or contact the nearest Author-
ized Service Centre.A rectangular symbol is
shown instead of numbers
on the Temperature Display.Temperature sensor prob-
lem.Contact the nearest Author-
ized Service Centre (the cool-
ing system will continue to
keep food products cold, but
temperature adjustment will
not be possible).The lamp does not work.The lamp is in stand-by.Close and open the door.The lamp does not work.The lamp is defective.Contact the nearest Author-
ized Service Centre.ENGLISH11  
						

							ProblemPossible causeSolutionThe compressor operates
continually.Temperature is set incor-
rectly.Refer to "Operation" chapter. Many food products were
put in at the same time.Wait some hours and then
check the temperature again. The room temperature is
too high.Refer to climate class chart on
the rating plate. Food products placed in
the appliance were too
warm.Allow food products to cool to
room temperature before stor-
ing.The door is not closed cor-
rectly.Refer to "Closing the door".The COOLMATIC function
is switched on.Refer to "COOLMATIC func-
tion".The compressor does not
start immediately after
pressing the COOLMATIC,
or after changing the tem-
perature.This is normal, no error has
occurred.The compressor starts after a
period of time.Water flows inside the refrig-
erator.The water outlet is clog-
ged.Clean the water outlet.Food products prevent
that water flows into the
water collector.Make sure that food products
do not touch the rear plate.Water flows on the floor.The melting water outlet is
not connected to the
evaporative tray above the
compressor.Attach the melting water out-
let to the evaporative tray.Temperature cannot be set.The FROSTMATIC or 
COOLMATIC function is
switched on.Switch off FROSTMATIC or 
COOLMATIC manually, or wait
until the function resets auto-
matically to set the tempera-
ture. Refer to "FROSTMATIC
or COOLMATIC function".DEMO appears on the dis-
play.The appliance is in demon-
stration mode.Keep the Mode pressed for
approximately 10 seconds un-
til a long sound is heard and
display shuts off for a short
time.The temperature in the ap-
pliance is too low/too high.The temperature regulator
is not set correctly.Set a higher/lower tempera-
ture.www.aeg.com12 
						

							ProblemPossible causeSolutionThe door is not closed cor-
rectly.Refer to "Closing the door".The food products' tem-
perature is too high.Let the food products temper-
ature decrease to room tem-
perature before storage.Many food products are
stored at the same time.Store less food products at the
same time.The door has been
opened often.Open the door only if necessa-
ry.The COOLMATIC function
is switched on.Refer to "COOLMATIC func-
tion".There is no cold air circula-
tion in the appliance.Make sure that there is cold air
circulation in the appliance.If the advice does not lead to
the desired result, call the
nearest brand-mark service.7.2  Closing the door
1.Clean the door gaskets.
2. If necessary, adjust the door. Refer to
"Installation".
3. If necessary, replace the defective
door gaskets. Contact the Service
Center.
7.3  Replacing the lamp
The appliance is equipped with a longlife
LED interior light.
Only service is allowed to replace the
lighting device. Contact your Service Center .8.  INSTALLATIONWARNING!
Refer to Safety chapters.8.1  Positioning
This appliance can be installed in a dry,
well ventilated indoor where the ambient
temperature corresponds to the climate
class indicated on the rating plate of the
appliance:
Climate
classAmbient temperatureSN+10°C to + 32°CN+16°C to + 32°CClimate
classAmbient temperatureST+16°C to + 38°CT+16°C to + 43°CENGLISH13   
						

							Some functional problems
might occur for some types of
models when operating
outside of that range. The
correct operation can only be
guaranteed within the
specified temperature range.
If you have any doubts
regarding where to install the
appliance, please turn to the
vendor, to our customer
service or to the nearest
Service Centre8.2  Installation of the
CLEANAIR CONTROL Filter
The carbon air filter is an active carbon filter which absorbs bad odors and
permits to maintain the best flavour and
aroma for all foodstuffs without risk of
odor cross contamination.
On delivery the carbon filter is in a plastic bag to preserve performance. The filter
should be placed in the drawer before
the appliance is turned on.
1. Open the drawer.
2. Take the filter out of the plastic bag.
3. Insert the filter in the drawer.
4. Close the drawer.
The filter should be handled
carefully so fragments do not
loosen from the surface. Make
sure that the air lever drawer
is closed to obtain proper
function.8.3  Electrical ConnectionCAUTION!
Any electrical work required to
install this appliance should
be carried out by a qualified
electrician or competent
person.WARNING!
This appliance must be
earthed. The manufacturer
declines any liability should
these safety measures not be
observed.
The wires in the mains lead are coloured
in accordance with the following code:
• A - green and yellow: Earth
• C - brown: Live
• D - blue: Neutral
As the colours of the wires in the mains
lead of this appliance may not
correspond with the coloured markings
identifying the terminals in your plug,
proceed as follows:
1. Connect the wire coloured green and
yellow to the terminal marked either
with the letter “E“ or by the earth
symbol 
 or coloured green and
yellow.
2. Connect the wire coloured blue to
the terminal either marked with the
letter “N“ or coloured black.
3. Connect the wire coloured brown to
the terminal either marked with the
“L“ or coloured red.
www.aeg.com14     A BC D E   
						

							4.Check that no cut, or stray strands of
wire is present and the cord clamp ( E ) is secure over the outer sheath. 
Make sure the electricity supply
voltage is the same as that indicated
on the appliance rating plate.
5. Switch on the appliance.
The appliance is supplied with a 13 amp
fuse ( B). In the event of having to change
the fuse in the plug supplied, a 13 amp ASTA approved (BS 1362) fuse must be
used.WARNING!
A cut off plug inserted into a
13 amp socket is a serious
safety (shock) hazard. Ensure
that it is disposed of safely.8.4  Door reversibility
The door of the appliance opens to the
right. If you want to open the door to the
left, follow these steps before you install
the appliance:
1. Loosen and remove the upper pin.
2.Remove the door.
3. Remove the spacer.
4. With a key, loosen the lower pin.
5. Tighten the lower pin on the
opposite side.
6. Install the spacer.
7. Install the door.
8. Tighten the upper pin.8.5  Ventilation requirements
The airflow behind the appliance must
be sufficient.
8.6  Installing the applianceCAUTION!
Make sure that the mains
cable can move freely.
1. If necessary cut the adhesive sealing
strip and then apply it to the
appliance as shown in figure.
2. Drill the unit using a Ø 2.5 mm drill
(10 mm max. penetration).
3. Fix the square fitting to the
appliance.
ENGLISH15   5 cmmin. 
200 cm2
min. 200 cm
2  x
x  
						

							4.Install the appliance in the niche.
5. Push the appliance in the direction of
the arrows (1) until the upper gap cover stops against the kitchen
furniture.
6. Push the appliance in the direction of
the arrows (2) against the cupboard on the opposite side of the hinge.
7. Adjust the appliance in the niche. 
Make sure that the distance between
the appliance and the cupboard front-edge is 44 mm.
The lower hinge cover (in the
accessories bag) makes sure that the
distance between the appliance and
the kitchen furniture is correct.
Make sure that the clearance
between the appliance and the
cupboard is 4 mm.
8. Open the door. Put the lower hinge
cover in position.
9. Attach the appliance to the niche
with 4 screws.
10. Remove the correct part from the
hinge cover (E). Make sure to remove the part DX, in the case of right
hinge, SX in opposite case.
11. Attach the covers (C, D) to the lugs
and the hinge holes.
www.aeg.com16Ø 2.5 mm
13 mm
1
32 1
2 44mm
4mm II   
						

							12.Install the vent grille (B).
13. Attach the hinge covers (E) to the
hinge.
14. Disconnect the parts (Ha), (Hb), (Hc)
and (Hd).
15. Install the part (Ha) on the inner side
of the kitchen furniture.
16. Push the part (Hc) on the part (Ha).
17.Open the appliance door and the
kitchen furniture door at an angle of
90°.
18. Insert the small square (Hb) into
guide (Ha).
19. Put together the appliance door and
the furniture door and mark the
holes.
ENGLISH17EEB
D
C Hb HaHc
Hd 21 mm
~50 mm ~50 mm
90o
90o
90o Ha
Hc  
						

							20.Remove the small squares and drill
holes with ø 2 mm at 8 mm from the
outer edge of the door.
21. Place the small square on the guide
again and fix it with the screws
supplied.
22. Align the kitchen furniture door and
the appliance door by adjusting the
part (Hb).
23. Press the part (Hd) on the part (Hb).
Do a final check to make sure that:
• All screws are tightened.
• The sealing strip is attached tightly to the cabinet.
• The door opens and closes correctly.
9.  NOISES
There are some sounds during normal running (compressor, refrigerant circulation).
www.aeg.com18Ha
Hb 8 mm Hb HbHd BRRR!
HISSS!
CLICK!
BLUBB!
CRACK!
SSSRR
R!
OK  
						

							10. TECHNICAL INFORMATION10.1  Technical data   Heightmm1855Widthmm545Depthmm575VoltageVolts230 - 240ENGLISH19CLICK!CLICK!SSSRRR!SSSRRR! BRRR!BRRR!HISSS!HISSS! BLUBB!BLUBB!CRACK!CRACK!  
						

							   FrequencyHz50The technical information are situated in
the rating plate, on the external orinternal side of the appliance and in the energy label.11.  ENVIRONMENTAL CONCERNSRecycle the materials with the symbol .
Put the packaging in applicable
containers to recycle it. Help protect the
environment and human health and to recycle waste of electrical and electronic
appliances. Do not dispose appliances
marked with the symbol 
 with the
household waste. Return the product to
your local recycling facility or contact
your municipal office.
*
www.aeg.com20