AEG Freestanding freezer A81000TNX1 User Manual

							ProblemPossible causeSolutionThe temperature in the ap-
pliance is too low/too high.The temperature regulator is
not set correctly.Set a higher/lower tempera-
ture.The door is not closed cor-
rectly.Refer to "Closing the door".The food products' tempera-
ture is too high.Let the food products tem-
perature decrease to room
temperature before storage.Many food products are
stored at the same time.Store less food products at
the same time.The door has been opened
often.Open the door only if neces-
sary.The FROSTMATIC function
is switched on.Refer to "FROSTMATIC
function".There is no cold air circula-
tion in the appliance.Make sure that there is cold
air circulation in the appli-
ance.Door does not open easily.You attempted to re-open
the door immediately after
closing.Wait a few seconds between
closing and re-opening of
the door.If the advice does not lead
to the desired result, call the
nearest Authorized Service
Centre.8.2  Closing the door
1.Clean the door gaskets.
2.If necessary, adjust the door. Refer to
"Installation".
3. If necessary, replace the defective
door gaskets. Contact the Authorised
Service Centre.9.  INSTALLATIONWARNING!
Refer to Safety chapters.9.1  Positioning
Install the appliance in a dry, well
ventilated indoors where the ambient
temperature corresponds to the climate class indicated on the rating plate of theappliance.
Climate
classAmbient temperatureSN+10°C to + 32°CN+16°C to + 32°CST+16°C to + 38°CT+16°C to + 43°CENGLISH11   
						

							Some functional problems
might occur for some types
of models when operating
outside of that range. The
correct operation can only
be guaranteed within the
specified temperature
range. If you have any
doubts regarding where to
install the appliance, please
turn to the vendor, to our
customer service or to the
nearest Authorised Service
Centre.9.2  Rear spacers
In the bag with the documentation, there
are two spacers which must be fitted as
shown in the figure.
1. Fit the spacers into the holes. Make
sure that the arrow (A) is positioned
as shown in the picture.
2. Turn counter-clockwise the spacers
through 45° until they lock into place.
9.3  Levelling
When placing the appliance ensure that
it stands level. This can be achieved by two adjustable feet at the bottom in
front.
9.4  LocationIt must be possible to
disconnect the appliance
from the mains power
supply; the plug must
therefore be easily
accessible after installation.
The appliance should be installed well
away from sources of heat such as
radiators, boilers, direct sunlight etc.
Ensure that air can circulate freely around
the back of the cabinet. To ensure best
performance, if the appliance is
positioned below an overhanging wall
unit, the minimum distance between the
top of the cabinet and the wall unit must
be at least 100 mm . Ideally, however, the appliance should not be positioned
below overhanging wall units. Accurate
levelling is ensured by one or more
adjustable feet at the base of the
cabinet.
www.aeg.com12 45°45°A
1
2 2   100 mm
15 mm 15 mm  
						

							9.5 Door reversibilityWARNING!
Before carrying out any
operations, remove the plug
from the power socket.CAUTION!
To carry out the following
operations, we suggest that
this be made with another
person that will keep a firm
hold on the doors of the
appliance during the
operations.
1. Tilt back the appliance carefully so
that the compressor cannot touch
the floor.
2. Unscrew both adjustable feet.
3.Unscrew the screws of the door
bottom hinge.
4. Take off the appliance door by
pulling it slightly downwards.
5. Unscrew the top door hinge pin of
the appliance then screw it back on the other side.
6. Fit the appliance door on the upper
door hinge pin.
7. Remove the lower hinge. Put over
the pin in the direction of the arrow.
8. Unscrew and install the screw on the
opposite side.
9. Install the lower hinge on the
opposite side leaving the position of
the door unchanged.
10. Screw in the one screw in the place
set free on the other side as well as the adjustable feet (2 pieces).
11. Remove and install the handle on the
opposite side.CAUTION!
Reposition, level the appliance, wait for at least
four hours and then connect
it to the power socket.Do a final check to make
sure that:
• All screws are tightened. • The magnetic seal adheres to the cabinet.
• The door opens and closes correctly.
If the ambient temperature
is cold (i.e. in Winter), the
gasket may not fit perfectly
to the cabinet. In that case,
wait for the natural fitting of
the gasket.
In case you do not want to
carry out the above
mentioned operations,
contact the nearest
Authorised Service Centre.
The Authorised Service
specialist will carry out the
reversibility of the doors at
your cost.ENGLISH13   2
1 12
3
4    
						

							9.6 Electrical ConnectionCAUTION!
Any electrical work required to install this appliance
should be carried out by a
qualified electrician or
competent person.WARNING!
This appliance must be
earthed.
The manufacturer declines
any liability should these
safety measures not be
observed.
The wires in the mains lead are coloured
in accordance with the following code:
• A - green and yellow: Earth
• C - brown: Live
• D - blue: Neutral
As the colours of the wires in the mains
lead of this appliance may not
correspond with the coloured markings
identifying the terminals in your plug,
proceed as follows:
1. Connect the wire coloured green and
yellow to the terminal marked either
with the letter “E“ or by the earth
symbol 
 or coloured green and
yellow.
2. Connect the wire coloured blue to
the terminal either marked with the
letter “N“ or coloured black.
3. Connect the wire coloured brown to
the terminal either marked with the
“L“ or coloured red.
4. Check that no cut, or stray strands of
wire is present and the cord clamp
( E ) is secure over the outer sheath.
Make sure the electricity supply
voltage is the same as that indicated on the appliance rating plate.
5. Switch on the appliance.
The appliance is supplied with a 13 amp
fuse ( B). In the event of having to change
the fuse in the plug supplied, a 13 amp
ASTA approved (BS 1362) fuse must be
used.
WARNING!
A cut off plug inserted into a
13 amp socket is a serious
safety (shock) hazard. Ensure
that it is disposed of safely.10.  NOISES
There are some sounds during normal running (compressor, refrigerant circulation).
www.aeg.com14  A BC D E   BRRR!
HISSS!
CLICK!
BLUBB!
CRACK!
SSSRR
R!
OK  
						

							11. TECHNICAL INFORMATION11.1  Technical data   Heightmm850Widthmm550Depthmm612Rising timeHours22ENGLISH15CLICK!CLICK!SSSRRR!SSSRRR! BRRR!BRRR!HISSS!HISSS! BLUBB!BLUBB!CRACK!CRACK!  
						

							   VoltageVolts220 - 240FrequencyHz50The technical information is situated in
the rating plate, on the external orinternal side of the appliance and in the energy label.12.  ENVIRONMENTAL CONCERNSRecycle the materials with the symbol .
Put the packaging in applicable
containers to recycle it. Help protect the
environment and human health and to recycle waste of electrical and electronic
appliances. Do not dispose appliancesmarked with the symbol  with the
household waste. Return the product to
your local recycling facility or contact
your municipal office.
*
www.aeg.com16   
						

							ENGLISH17 
						

							www.aeg.com18 
						

							ENGLISH19 
						

							www.aeg.com/shop212001479-A-082016