AEG Freestanding dishwasher F66792W0P User Manual

 start to flash and the
display is blank.
2. Press 
.
• The indicators 
, ,  and
 go off.
• The indicator 
 continues to
flash.
• The display shows the current
setting: e.g. 
= level 4.
– The levels of rinse aid are from 0A to 6A.
– Level 0 = no rinse aid is
released.
3. Press 
 again and again to change
the setting.
4. Press the on/off button to confirm
the setting.
6.4  Use of rinse aid and multi-
tablets
The factory setting of the rinse aid dispenser is with the dispenser activated. This means that...

6.6 Acoustic signals
Acoustic signals sound when a
malfunction of the appliance occurs. It is
not possible to deactivate these acoustic signals.
There is also an acoustic signal that
sounds when the programme is
completed. By default this acoustic
signal is deactivated but it is possible to activate it.How to activate the acoustic
signal for the end of
programme
The appliance must be in programme
selection mode.
1. To enter the user mode press and
hold simultaneously 
 and  until
the indicators 
, , ,...

7.2 Multitab
Activate this option when you use multi- tablets that integrate the salt, rinse aid
and detergent functions. They can also contain other cleaning or rinsing agents.
This option deactivates the release of salt. The salt indicator does not come on.
This option also deactivates the release
of rinse aid but only when the rinse aid dispenser is deactivated, (rinse aid
indicator does not come on). If the rinse
aid dispenser is activated, rinse aid is
released even with the option Multitab...

4.Remove the salt around the opening
of the salt container.
5. Turn the cap of the salt container
clockwise to close the salt container.
Water and salt can come out
from the salt container when
you fill it. Risk of corrosion.
To prevent it, after you fill
the salt container, start a
programme.8.2  How to fill the rinse aid
dispenserCAUTION!
Only use rinse aid
specifically designed for dishwashers.
1. Open the lid ( C).
2. Fill the dispenser ( B) until the rinse
aid reaches the marking...

9.1 Using the detergentCAUTION!
Only use detergent specifically designed for
dishwashers.
1. Press the release button ( A) to open
the lid ( C).
2. Put the detergent, in powder or
tablets, in the compartment ( B).
3. If the programme has a prewash
phase, put a small quantity of
detergent on the inner part of the
appliance door.
4. Close the lid. Make sure that the lid
locks into position.
9.2  Setting and starting a
programmeThe Auto Off function
This function decreases energy
consumption by...

Cancelling the delay start while
the countdown operates
When you cancel the delay start you
have to set the programme and options
again.
Press and hold  RESET until the appliance
is in programme selection mode.Cancelling the programme
Press and hold  RESET until the appliance
is in programme selection mode.
Make sure that there is detergent in the detergent dispenser before you start a
new programme.End of programme
When the programme is completed and you open the door, the appliance is
automatically...

10.3 What to do if you want to
stop using multi-tablets
Before you start to use separately
detergent, salt and rinse aid do the following procedure.
1. Set the highest level of the water
softener.
2. Make sure that the salt and rinse aid
containers are full.
3. Start the shortest programme with a
rinsing phase. Do not add detergent
and do not load the baskets.
4. When the programme is completed,
adjust the water softener according
to the water hardness in your area.
5. Adjust the released quantity of...

1.Turn the filter ( B) counterclockwise
and remove it.
2. Remove the filter ( C) out of filter ( B). 
3. Remove the flat filter ( A).
4. Wash the filters.
5.Make sure that there are no residues
of food or soil in or around the edge
of the sump.
6. Put back in place the flat filter ( A).
Make sure that it is correctly
positioned under the 2 guides.
7. Reassemble the filters ( B) and ( C).
8. Put back the filter ( B) in the flat filter
( A ). Turn it clockwise until it locks.
CAUTION!
An incorrect position...

11.2 Cleaning the spray arms
Do not remove the spray arms. If the
holes in the spray arms are clogged,
remove remaining parts of soil with a thin
pointed object.11.3  External cleaning
• Clean the appliance with a moist soft
cloth.
• Only use neutral detergents.
• Do not use abrasive products, abrasive cleaning pads or solvents.
11.4  Internal cleaning
• Carefully clean the appliance, including the rubber gasket of the
door, with a soft moist cloth.
• If you regularly use short duration programmes, these...

For alarm codes not described in the
table, contact an Authorised Service
Centre.12.1  The washing and drying results are not satisfactoryProblemPossible solutionThere are whitish streaks or
bluish layers on glasses and
dishes.• The release quantity of rinse aid is too much. Adjust the rinse aid selector to a lower position.
• The quantity of detergent is too much.There are stains and dry water
drops on glasses and dishes.• The released quantity of rinse aid is not sufficient. Ad- just the rinse aid...