AEG B4101-5 User Manual

							Folding down the heating element
1. Remove the shelf support rails.
2. Hold the heating element with the two
hands at the front
3. Pull it forwards against the spring pres-
sure and out along the support on both
sides.
4. The heating element folds down.
The oven ceiling is ready to clean.
Installing the heating element
1. Install the heating element in opposite se-
quence.
Install the heating element correctly on the two sides above the support on the inner wall
of the oven.
2. Insert shelf support rails.
Shelf Support Rails
Removing the shelf support rails
1. Pull the front of the shelf support rail
away from the side wall.
2. Pull the rear shelf support rail away from
the side wall and remove it.
Installing the shelf support rails
Install the shelf support rails in opposite sequence.
Important! The rounded ends of the shelf support rails must point to the front!
Oven lamp
WARNING!
There is a danger of electrical shock!
2
1
Care and cleaning21 
						

							Before you change the oven lamp:
• Switch off the oven.
• Remove the fuses in the fuse box or switch off the circuit breaker.
Put a cloth on the bottom of the oven for protection of the oven light and glass cover.
Replacing the oven light bulb/cleaning the glass cover
1. Turn the glass cover anti-clockwise to remove it.
2. Clean the glass cover.
3. Replace the oven light bulb with applicable 300°C heat-resistant oven light bulb.
4. Install the glass cover.
Oven door and glass panels
To clean the oven door remove it.
CAUTION!
Be careful when you remove the door from the appliance. The door is heavy!
Removing the oven door
1. Open the oven door as far as it goes.
2. Lift up clamping levers (A) on the two
door hinges fully.
3. Close the oven door until the first posi-
tion (angle approximately 45°).
4. Hold of the oven door with one hand on
each side and pull it away from the oven
at an upwards angle.
Put the oven door with the outer side down
on a soft and level surface to prevent scratch-
es
5. Now you can remove the inner glass pan-
els and clean them.
To install the door follow the procedure in
reverse.
The oven door has 2, 3 or 4 panels of glass (depends on the model)
A
A
45°
22Care and cleaning 
						

							Removing and cleaning the door glasses
1. Hold the door trim (B) on the top edge of
the door at the two sides and push in-
wards to release the clip seal.
2. Pull the door trim to the front to remove
it.
3. Hold the door glass panels on their top edge one by one and pull them upwards out of
the guide
4. Clean the door glass panels.
To install panels follow the procedure in reverse. Insert the smaller panel first, then the
larger.
WHAT TO DO IF…
WARNING!
Refer to Safety information chapter.
ProblemPossible causeRemedy
The oven does not heat upThe oven is not switched onSwitch on the oven
The oven does not heat upThe clock is not setSet the clock
The oven does not heat upThe necessary settings are not
setControl the settings
The oven does not heat upThe fuse in the fuse box is re-
leasedControl the fuse. If the fuse is
released more than one time,
refer to a qualified electrician.
The oven lamp does not oper-
ateThe oven lamp is defectiveReplace the oven lamp
B
What to do if…23 
						

							ProblemPossible causeRemedy
Steam and condensation settle
on the food and in the oven
cavityYou left the dish in the oven
for too longDo not leave the dishes in the
oven for longer than 15-20 mi-
nutes after the cooking process
ends
The display shows “12.00”A power cutReset the clock
If you cannot find a solution to the problem yourself, contact your dealer or the service
centre.
The necessary data for the service centre is on the rating plate. The rating plate is on the
front frame of the oven cavity.
We recommend that you write the data here:
Model (MOD.) .........................................
Product number (PNC) .........................................
Serial number (S.N.) .........................................
TECHNICAL DATA
Voltage230 V
Frequency50 Hz
ENVIRONMENT CONCERNS
The symbol  on the product or on its packaging indicates that this product may not be
treated as household waste. Instead it should be taken to the appropriate collection point
for the recycling of electrical and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste
handling of this product. For more detailed information about recycling of this product,
please contact your local council, your household waste disposal service or the shop where
you purchased the product.
Packaging material
The packaging material is environmentally-friendly and recyclable. Plastic parts are marked
with international abbreviations such as PE, PS, etc. Dispose of the packaging material in
the containers provided for this purpose at your local waste management facility.
24Technical data 
						

							25 
						

							26 
						

							27 
						

							 www.aeg.com/shop
   
892938796-C-032011