AEG A 70318 Gs Operating Instructions

Installation
818 22 90-00/011
Electrical Connection
Any electrical work required to install this appliance should be carried 
out by a qualified electrician or competent person.
1 WARNING – THIS APPLIANCE MUST BE EARTHED
The manufacturer declines any liability should these safety measures 
not be observed.
Before switching on, make sure the electricity supply voltage is the 
same as that indicated on the appliance rating plate. The rating plate is 
inside, on the left.
The appliance is supplied with a 13...

12818 22 90-00/0
Reversing the door
The door hinges can be changed from right (as supplied) to left if 
required to suit the location where the appliance is installed. 
1 Warning! Unplug from the mains before reversing the door. 
0 1.Open the door and remove the 
plinth cover to the front. Move 
the door hinge bracket cover on 
the plinth cover from the left to 
the right. Close the door. 
2.With the door closed, remove the 
cross-head screws from the lower 
door hinge bracket and remove 
the door hinge...

Reversing the door
818 22 90-00/013
4.Remove the door fitting on the 
lower right (1) and reposition the 
door hinge bracket cover from the 
lower left to the right of the door 
(2), place the door fitting supplied 
in the lower left of the door (3).
Carefully remove the door to the 
front and place on one side. 
5.Move the upper hinge bracket 
pivot to the left. 
6.Carefully slide the door onto the 
top hinge bracket pivot and close. 
7.Place the lower door hinge 
bracket with the hinge bracket 
pivot...

Reversing the door
14818 22 90-00/0
8.Unscrew the top handle bracket 
from the handle rod (1). Unscrew 
the bottom handle bracket from 
the door (2).
9.Unscrew the top handle bracket 
from the door (3) and screw onto 
the bottom right-hand side of the 
door (4).
1 Caution! Do not overtighten the 
screws (max. 2 Nm) as you may 
damage the door handle.
10.Turn the handle bracket with the 
handle rod 180° and screw them 
to the door (5) and the fitted han-
dle bracket (6). 
1 Caution! Do not overtighten the...

818 22 90-00/015
Description of the appliance
View of the appliance
(various models)
áControl panel
àInterior Illumination 
âCompartments with drawers 
äMaxi-Box
ãDrawer (for frozen food storage only) 
Cold accumulation block
(not on all models)
There is one cold accumulation block in the freezer.
Refer to the section “Prior to Initial Start–Up” concerning freezing of 
the cold accumulation block.
3 In the event of a power failure or malfunction, the cold accumulation 
block will increase the hold over...

Description of the appliance
16818 22 90-00/0
Control Panel
1ON/OFF button and stand-by display (green)
2Temperature display
3Temperature setting buttons
4FROSTMATIC button and FROSTMATIC indicator light (yellow)
5ALARM OFF button and warning indicator light (red) 
(see section: Control and Information Systems) 
Temperature setting buttons
The temperature is adjusted using the 
„+“ (WARMER) and „-“ (COLDER) buttons.
These buttons are connected to the temperature display.
 The temperature display is...

Description of the appliance
818 22 90-00/017
Temperature display
The temperature display shows several types of 
information.
 In normal operation the current freezer compartment temperature is 
displayed (ACTUAL temperature). 
 During temperature adjustment, a blinking display of the 
temperature selected at the moment occurs (DESIRED temperature). 
 In the event that frozen food has been partially or totally defrosted, 
perhaps as the result of a lengthy power failure, if the ALARM OFF 
button is...

18818 22 90-00/0
Prior to Initial Start–Up
1 Before connecting the appliance to the mains and putting it into oper-
ation for the first time, leave the appliance to stand for 30 minutes if 
was transported upright. After transport on its side, the appliance must 
be left to stand for 4 hours before putting it into operation. This is nec-
essary to allow the refrigerant to flow back into the compressor. Other-
wise the compressor may be damaged.
0 1.Please clean the appliance interior and all accessories...

818 22 90-00/019
Temperature Adjustment
0 1.Press either the „+“ (WARMER) or „-“ (COLDER) button.
The temperature display switches over and the DESIRED temperature 
currently set flashes on the temperature display.
2.To adjust to a warmer temperature, press the „+“ (WARMER) button. To 
adjust to a colder temperature, press the „-“ (COLDER) button. The 
changed setting is immediately displayed on the temperature display.
Each time one of the two buttons is pressed again the DESIRED temper-
ature is...

20818 22 90-00/0
Switching the Appliance Off
In order to protect frozen goods, the appliance is guarded against 
accidental switching off (child-proof).
0 1.To switch off press and hold the ON/OFF button for approximately 1 
second. Illumination at the temperature display goes off.
3 The appliance is only completely disconnected from the electricity 
supply when the power plug has been removed from the power outlet.
Note:
The appliance cannot be switched on or off if unplugged, or if there is 
no power...