Advidia Encoder Vp 8 V2 Vp 16 V2 Quick Start Guide

							           VP-8-V2 and VP-16-V2 Encoder  Quick Start Guide                                                                                                                                                                               
						

							VP-8-V2 and VP-16-V2 Series Encoder·Quick Start Guide 2 About this Manual This Manual is applicable to All-in-One NVR (Network Video Recorder). The  Manual  includes instructions  for  using  and  managing  the  product.  Pictures,  charts,  images  and  all  other  information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the company website  Please use this user manual under the guidance of professionals. Legal Disclaimer REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. OUR COMPANY  SHALL  NOT  TAKE  ANY  RESPONSIBILITES  FOR  ABNORMAL  OPERATION,  PRIVACY  LEAKAGE  OR  OTHER  DAMAGES RESULTING  FROM  CYBER  ATTACK,  HACKER  ATTACK,  VIRUS  INSPECTION,  OR  OTHER  INTERNET  SECURITY  RISKS;  HOWEVER, OUR COMPANY WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.  SURVEILLANCE  LAWS  VARY  BY  JURISDICTION.  PLEASE  CHECK  ALL  RELEVANT  LAWS  IN  YOUR  JURISDICTION  BEFORE  USING THIS  PRODUCT  IN  ORDER  TO  ENSURE  THAT  YOUR  USE  CONFORMS  THE  APPLICABLE  LAW.  OUR  COMPANY  SHALL  NOT  BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.  IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.  
						

							VP-8-V2 and VP-16-V2 Series Encoder·Quick Start Guide 3 Regulatory Information FCC Information FCC compliance: This equipment  has  been  tested and  found  to  comply with the  limits for  a Class A  digital  device,  pursuant to  part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide  reasonable  protection  against  harmful  interference  when the  equipment is  operated  in  a  commercial environment. This  equipment generates,  uses, and can  radiate radio  frequency energy  and,  if  not  installed  and  used  in  accordance  with  the  instruction  manual,  may  cause  harmful  interference  to  radio communications. Operation of this  equipment in  a residential  area is likely  to cause  harmful  interference in which  case the user will be required to correct the interference at his own expense. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the  applicable  harmonized  European  standards  listed  under  the  EMC  Directive  2004/108/EC,  the  RoHS Directive 2011/65/EU. 2012/19/EU (WEEE  directive):  Products marked  with  this symbol  cannot be  disposed  of  as  unsorted  municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of  equivalent  new  equipment,  or  dispose  of  it  at  designated  collection  points.  For  more  information  see: www.recyclethis.info 2006/66/EC  (battery  directive):  This  product  contains  a  battery  that  cannot  be  disposed  of  as  unsorted municipal  waste  in  the  European  Union.  See  the  product  documentation  for  specific  battery  information.  The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.  
						

							VP-8-V2 and VP-16-V2 Series Encoder·Quick Start Guide 4 Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.  The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected.    Warnings ● Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. ● In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information. ● Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 100 to 240 VAC or 12 VDC according to the IEC60950-1 standard. Please refer to technical specifications for detailed information. ● Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. ● Please make sure that the plug is firmly connected to the power socket.    ● If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.   Warnings Follow  these safeguards  to  prevent  serious injury or death. Cautions Follow  these  precautions to  prevent  potential  injury  or material damage.   
						

							VP-8-V2 and VP-16-V2 Series Encoder·Quick Start Guide 5 Preventive and Cautionary Tips Before connecting and operating your device, please be advised of the following tips: • Ensure unit is installed in a well-ventilated, dust-free environment. • Unit is designed for indoor use only. • Keep all liquids away from the device. • Ensure environmental conditions meet factory specifications. • Use the device in conjunction with an UPS if possible. • Power down the unit before connecting and disconnecting accessories and peripherals. • Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer.   
						

							 VP-8-V2 and VP-16-V2 Series Encoder · Quick Start Guide 6 Chapter 1  Panel Description 1.1 Front Panel VP-8-V2/VP-16-V2:  Figure 1. 1 VP-8-V2/VP-16-V2 Front Panel  Table 1. 1 Indicator Description  Indicator  Description  1 POWER  Lights in green when the device is powered on. 2  Not Used 3 Tx/Rx 1. Does not light when the network is not connected;  2. Blinks in green when the data is transmitting / receiving;  3. Blinks at higher frequency when the data for transmitting / receiving is larger. 1.2 Rear Panel VP-8-V2:  Figure 1. 2 VP-8-V2 Rear Panel  VP-16-V2:  Figure 1. 3 VP-16-V2    
						

							 VP-8-V2 and VP-16-V2 Series Encoder · Quick Start Guide 7 Table 1. 2 Interface Description   Description  1 VIDEO IN 2 AUDIO IN, RCA Connector 3 AUDIO OUT, RCA Connector 4 LAN Network Interface 5 RS-485 Serial Interface 6 12 VDC Power Input 7 Power Switch 8 ALARM IN and ALARM OUT 9 GND  
						

							 VP-8-V2 and VP-16-V2 Series Encoder · Quick Start Guide 8 Chapter 2  Installation 2.1 Pre-Installation The V2 Series Encoder is advanced surveillance equipment that should be installed with care. Please take into consideration the following precautionary steps before installation of the Encoder.    1. Keep all liquids away from the Encoder.  2. Install the Encoder in a well-ventilated and dust-free area. 3. Ensure environmental conditions meet factory specifications.    2.2 Installation During the installation of the Encoder: 1. Use brackets for rack mounting. 2. Ensure there is ample room for audio and video cables. 3. When installing cables, ensure that the bend radius of the cables are no less than five times than its diameter. 4. Connect both the alarm and RS-485 cable. 5. Allow at least 2cm (≈0.75") of space between racks mounted devices. 6. Ensure the Encoder is grounded. 7. Environmental temperature should be within the range of -10º C to 55º C, 14º F to 13º F. 8. Environmental humidity should be within the range of 10% to 90%.                       
						

							 VP-8-V2 and VP-16-V2 Series Encoder · Quick Start Guide 9 2.3 Access  to VP-8-V2 and  VP-16-V2 ENCODER via Web Browser  Steps: 1. Power on the encoder, and connect the encoder to the network. 2. Input  the  IP  address  into  the  address  bar  of  the  web  browser,  and  click  Enter  to  enter  the  activation interface.  The  default  IP  address  of  the  network  encoder  is  192.0.0.64.  You  are  recommended  to  change  the  default  IP address after your access. 3. Default username is admin Default password is 12345.    The V2  ENCODER can  also  be  accessed  by  WEB  Browser  for  configuration  and  operation. The  supported  WEB browsers  include:  Internet  Explorer  6/7/8/9 and  above,  Firefox  3.5  and  above,  Chrome  8  and  above,  Safari 5.0.2 and above. Open  WEB  browser,  input  the  IP  address  of V2  ENCODER (e.g., http://192.0.0.64)  and  then  press the Enter key on PC. The login interface is displayed.   When  the  HTTPS feature is  enabled,  the  system  will use  the HTTPS login  mode (e.g., https://192.0.0.64) by default. You  can  also  input http://IP  address/index.asp (e.g., http://192.0.0.64/index.asp)  if  you  want  to  use HTTP mode to log into the device.  Figure 2. 1 Login Interface Input the user name and password to log into the system.    
						

							 VP-8-V2 and VP-16-V2 Series Encoder · Quick Start Guide 10 In the Login dialog box, if you have entered the wrong password for 7 times for the admin user or 5 times for the normal user, the current user account will be locked for 60 seconds.   You should download and install the plug-in for the first time to use.   Figure 2. 2 Message from Webpage 2.4 Starting Live V iew 1. In the live view window, select a playing window by clicking the mouse.    2. Double-click a camera from the device list to start the live view.    Figure 2. 3 Live View Interface 3. You can click the  button on the toolbar to start the live view of all cameras on the device list.  Refer to the following table for the description of buttons on the live view window: