Advidia A65 Bullet Camera Quick Start Guide

							Network Dome Camera · Quick Start Guide  10Slot Cover  Figure 1-2 Remove Card Cover 2. Insert the SD card into the SD card slot. Micro SD Card Figure 1-3 Insert the Card 3. (Optional) Push the inserted micro SD card inside to remove the micro SD card. 4. Re-install the card cover and fasten the two screws to complete the installation. 
						

							Network Dome Camera · Quick Start Guide  112 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12V DC or 24V AC, please make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment. ● Make sure that the wall is strong enough to withstand four times the weight of the camera and the bracket. For the camera that supports IR, you are required to pay attention to the following precautions to prevent IR reflection:  ● Dust or grease on the dome cover will cause IR reflection. Please do not remove the dome cover film until the installation is finished. If there is dust or grease on the dome cover, clean the dome cover with clean soft cloth and isopropyl alcohol. ● Make sure that there is no reflective surface too close to the camera lens. The IR light from the camera may reflect back into the lens causing reflection.  ● The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS. Fasten the dome cover to camera body so that the foam ring and the dome cover are attached seamlessly.   
						

							Network Dome Camera · Quick Start Guide  122.1 Ceiling Mounting Steps:  1. Drill the screw holes and the cable hole in the ceiling according to the supplied drill template. Ceiling Mounting11:Screw Hole forBracket2:Screw Hole forMounting Base1112222 Figure 2-1 Drill Template 2. Fix the camera to the wall with the supplied screws.  
						

							Network Dome Camera · Quick Start Guide  13 Please insert the expansion screws first if the camera is mounted to the cement ceiling. And you can use the self-tapping screws directly if camera is mounted to the wooden ceiling.  Figure 2-2 Install the Camera 3. Adjust the surveillance angle. 1). Loosen No.1 lock screw to adjust the tilt angle [0 °~100°]. 2). Loosen No.2 lock screw to adjust the pan angle [0°~360°]. 3). Loosen No.3 lock screw to rotate the camera [0°~360°]. 4). Tighten the lock screws.  A wrench is supplied to loosen and tighten the screws.  
						

							Network Dome Camera · Quick Start Guide  140°~100°0°~360°0°~360°123 Figure 2-3 Adjust the Surveillance Angle  Figure 2-4 Supplied Wrench 4.  (Optional) Install the water-proof jacket for network interface.  It is recommended to adopt the water-proof jacket (supplied) for the network interface when the camera is installed outdoor.  1). If the network cable has been settled down, cut off the plug of the network cable first.  
						

							Network Dome Camera · Quick Start Guide  152). Route the network cable through the following components in sequence: fix nut, water-proof ring, and the main body of the water-proof jacket, as shown in the figure. 3). Insert the water-proof ring into the main body of the water-proof jacket, to increase the sealing ability of the components. 4). Wire the plug and network cables up. 5). Fix the O-ring to the network interface of the camera, and then connect the network cables. 6). Wrap the network interface with the main body of the water-proof jacket, and then rotate the fix nut clockwise to assemble it to the main body of the water-proof jacket. Network InterfaceO-ringPlugWater-proof JacketWater-proof RingFix NutNetwork Cable Figure 2-5 Install the Water-proof Jacket  
						

							Network Dome Camera · Quick Start Guide  162.2 Wall Mounting with a Junction Box Steps: 1. Drill the screw hole and cable hole according to the supplied drill template (shown as Figure 2-1). 2. Align the screw holes of the junction box to the drill template, and fix the junction box to the wall with screws. 3. Route the cables. 4. Fix the camera to the junction box with screws. 5. Adjust the surveillance angle according to step 3 in Chapter 2.1. 6. Install the water-proof jacket according to step 4 in Chapter 2.1. Drill Template Figure 2-6 Installation with a Junction Box  
						

							Network Dome Camera · Quick Start Guide  172.3 Wall Mounting with a Gang Box  An adapter plate should be purchased separately if you mount the camera to a gang box. Steps: 1. Install the adapter plate to the gang box. 2. Route the cables. 3. Fix the camera to the adapter plate with screws. 4. Adjust the surveillance angle according to step 3 in Chapter 2.1. 5. Install the water-proof jacket according to step 4 in Chapter 2.1. Adapter Plate Figure 2-7 Installation with a Gang Box  
						

							Network Dome Camera · Quick Start Guide  183 Setting the Network Camera over the LAN Purpose: To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install the Advidia Camera Finder Utility to search and change the IP of network camera.  The following figure shows the cable connection of network camera and PC:  Figure 3-1 Wiring over LAN  Set the IP address of the camera for accessing via LAN. Steps: To set the IP address, please use the Advidia Camera Finder Utility as described below:  To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install the Advidia Camera Finder Utility.  
						

							Network Dome Camera · Quick Start Guide  19Refer to the following introductions to set IP address with the Advidia Camera Finder Utility software (for more detailed instructions please download the Camera Finder manual from the Advidia Website www.advidia.com/support):  After launching the Advidia Camera Finder software, it automatically searches the online devices from the subnet where your computer is located.  This search may take 30 seconds or more depending on network size. After searching it will show total number and information of the Advidia cameras found on the network. Device information including the device type, IP address, port number, gateway, etc. will be displayed.  Figure 3-2 Advidia Camera Finder Note: To perform a manual search for additional cameras: