Advidia 44 V2, A 54v2 Quick Start Guide

 A-44 V2/A-54 V2 · Quick Start Guide  11Figure 1-4 Overview (4) Table 1-1 Description of Overview (2~3) No. Description No. Description 1 Black Liner 2 Bubble 3 Lens 4 BNC Interface 5 Reset 6 Status Indicator 7 Test Serial Port 8 Micro SD Card Slot 9 Adapter Plate 10 Side Outlet Table 1-2 Description of Overview (4) No. Description LAN（PoE） 10M/100M Self-adaptive Ethernet Port(PoE Supported) AUDIO OUT/IN： Audio Out/In CVBS，GND Auxiliary video output 1A，1B Alarm Out D+，D- RS-485 Interface IN，GND Alarm In...

 A-44 V2/A-54 V2 · Quick Start Guide  12Note: Press RESET for approximately 10 seconds when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. 2  Installation Before you start:  Make sure the device is in good condition and all the assembly parts are included.  Make sure all the related equipment is powered-off during the installation.  Check the specifications of the products to ensure they match the installation...

 A-44 V2/A-54 V2 · Quick Start Guide  13● Dust or grease on the dome cover will cause IR reflection. Please do not remove the dome cover film until the installation is finished. If there is dust or grease on the dome cover, clean the dome cover with clean soft cloth and isopropyl alcohol. ● Make sure that there is no reflective surface too close to the camera lens. The IR light from the camera may reflect back into the lens causing reflection.  ● The foam ring around the lens must be seated flush against...

 A-44 V2/A-54 V2 · Quick Start Guide  14the part shown in the figure below, and you can route the cables from the side outlet.  Figure 2-2 Side Outlet 2. Attach the adapter ring to the ceiling with the supplied screws.  Side Outlet 

 A-44 V2/A-54 V2 · Quick Start Guide  15Figure 2-3 Install the Adapter Plate 3. Align the camera base with the adapter ring and rotate the camera base counter clockwise to lock it into the adapter ring, and then secure it by tightening the lock screw.  Figure 2-4 Install Camera to Adapter Ring 4. Adjust the lens angle according to the figure below. Panning angle [0~80°], tilting angle [0~355°], and azimuth angle of the lens [0~355°].  LockScrew0~80°0~355°0~355° 

 A-44 V2/A-54 V2 · Quick Start Guide  16Figure 2-5 3-axis Adjustment 5. Adjust the focus and zoom. This camera is equipped with an electronic lens. You can adjust the zoom and focus by logging into the web interface of the device, and adjusting it from the PTZ control interface found on the top header of the Live View Image.  Figure 2-6 Zoom and Focus Adjustment of Electronic Lens 6. Insert the black liner to the dome drive. 7. Attach the bubble to the dome drive and rotate it to get tightened.  Figure...

 A-44 V2/A-54 V2 · Quick Start Guide  17 Figure 2-8 Complete the Installation  

 A-44 V2/A-54 V2 · Quick Start Guide  183 Setting the Network Camera over the LAN Purpose: To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install the Advidia Camera Finder Software to search and change the IP of network camera.  The following figure shows the cable connection of network camera and PC:  Figure 3-1 Wiring over LAN   Set the IP address of the camera for accessing via LAN. Steps: To set the IP...

 A-44 V2/A-54 V2 · Quick Start Guide  19Refer to the following introductions to set IP address with the Advidia Camera Finder Utility software (for more detailed instructions please download the Camera Finder manual from the Advidia Website www.advidia.com/support):  After launching the Advidia Camera Finder software, it automatically searches the online devices from the subnet where your computer is located.  This search may take 30 seconds or more depending on network size. After searching it will...

 A-44 V2/A-54 V2 · Quick Start Guide  20Click the refresh icon  to refresh the online device list manually. The newly discovered devices will be added to the list. Note: You can click on each column heading to order the information.  Modify device information Steps: 1). Select the device(s) to be modified in the device list as shown in Figure 3-3.  2). Click on “File” and select “Login Manager” as shown in Figure 3-4 to enter the username and password information of selected device(s). 3). Enter the...