Adtran Atlas 800 Series Dual Video User Manual
Here you can view all the pages of manual Adtran Atlas 800 Series Dual Video User Manual. The Adtran manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 31
Chapter 3. Operation 61200773L1-1A ATLAS 800 Series Video Module User Manual 31 ZERO The DTE is sending an excessive number of consecutive zeroes to the network interface. NO EXT CLK The DTE is not providing an external transmit clock. This alarm displays only if the Video Module DTE port is configured to get its transmit clock from the DTE. DTE S TATUSShows the status of key DTE interface signals. An asterisk (*) indicates the pres- ence of a signal and a hyphen (-) indicates no signal present....
Page 32
Chapter 3. Operation 32 ATLAS 800 Series Video Module User Manual 61200773L1-1A PLL/FIFODisplays the Phase Lock Loop (PLL) and FIFO status. C ONFIGURATIONAll of the following configurable parameters apply to the individual Video Module DTE ports. P RT Displays the port number. P ORT NAME Accepts any alpha-numeric name up to 16 characters long, to uniquely identify each DTE port on the Video Module. C LK +/- Controls the clock used by the ATLAS 800 Series to accept the transmit (TX) data from the DTE....
Page 33
Chapter 3. Operation 61200773L1-1A ATLAS 800 Series Video Module User Manual 33 DTR Selects the response to DTR transitions. The following table lists the configuration options for the DTR parameter with respect to the current configuration for the module in the Dial Plan. 0 I NH When the port detects an uninterrupted string of 0s being transmitted for more than one second, setting this parameter to O N will cause the ATLAS 800 Series to send 1s toward the network. T ESTThese options initiate...
Page 34
Chapter 3. Operation 34 ATLAS 800 Series Video Module User Manual 61200773L1-1A LOOPBACK STATUS This read-only option indicates a port’s current loopback status by displaying any of the following status messages: N O LOOPBACK ACTIVE PORT LOOPBACK ACTIVE LOOPING UP REMOTE UNIT... R EMOTE UNIT LOOPED BACK LOOPING DOWN REMOTE UNIT... R EMOTE LOOPUP FAILED PORT LOOPED FROM REMOTE SOURCE 511 Controls the activation of the 511 test pattern generator and detector. 511 pattern is generated inward through the...
Page 35
Chapter 3. Operation 61200773L1-1A ATLAS 800 Series Video Module User Manual 35 V. 3 5 Configures the interface for V.35 use. RS-449 Configures the interface for RS-449 use. L OOPBACK Configures the interface to emulate a connected loopback cable. CURRENT DTE TYPEDisplays the current configuration of the Video Module DTE Interface. MODULE ALARMSProvides a shortcut to the ALARM menu (see See “Alarm Status” on page 30.). TEST ACTIVITYProvides a shortcut to the TEST menu (see See “Test” on page 33.)...
Page 36
Chapter 3. Operation 36 ATLAS 800 Series Video Module User Manual 61200773L1-1A
Page 37
61200773L1-1A ATLAS 800 Series Video Module User Manual 37 Appendix ADial Plan Interface Configuration The IFCE CONFIG option for the DIAL PLAN menu (see Figure A-1) sets configura- tion parameters for the endpoint. These parameters vary by the type of port selected. The following section describes the configuration options available for the ATLAS 800 Series Video Module. To access these options, select D IAL PLAN from the ATLAS menu. Figure A-1. Dial Plan Menus The Video Module is only available...
Page 38
Appendix A. Dial Plan Interface Configuration 38 ATLAS 800 Series Video Module User Manual 61200773L1-1A ATLAS 800 SERIES VIDEO MODULE: USER TERMINATION The ATLAS 800 Series Video Module acts like the network while interfacing to user equipment (video equipment). When you are working in the U SER TERM section of the D IAL PLAN menu and SLT is defined as a Video Module, the following interface configuration options are available: DIALING METHODWrite Security: 3; Read Security: 5 Selects the method of...
Page 39
Appendix A. Dial Plan Interface Configuration 61200773L1-1A ATLAS 800 Series Video Module User Manual 39 STORED N UMBERS Write Security: 3; Read Security: 5 Enter the numbers to dial using the RS-366 Type II dialing interface in the stored numbers list. This list can contain up to 10 stored numbers. #Entry number (1-10) DIALActivator to dial or disconnect a call to the specified number. DESCRIPTIONAlphanumeric character string (up to 20 characters) used as a descriptor for the num- ber entry. Enter...
Page 40
Appendix A. Dial Plan Interface Configuration 40 ATLAS 800 Series Video Module User Manual 61200773L1-1A DEFAULT DIAL C ALL AS Write Security: 3; Read Security: 5 Specifies the call type used to populate the Bearer Capability Information Element in the ISDN Call Setup Message if not specified in the Smart Dial string. Options include: D IGITAL (Data), VOICE (Speech), or AUDIO (3.1kHz audio). DEFAULT S OURCE ID Write Security: 3; Read Security: 5 Defines the source ID assigned to this call to be...