ADT Security Services Vista 15 User Manual

							Recommendations for Proper Protection (contd)
- 41 -
Recommendations for Proper Intrusion Protection
For proper intrusion coverage, sensors should be located at every
possible point of entry to a home or commercial premises. This
includes skylights and upper windows in a multi-level building.
In addition, we recommend that radio backup be used in a security
system so that alarm signals can still be sent to the alarm monitoring
station in the event that the telephone lines are out of order (alarm
signals are normally sent over the phone lines, if connected to an
alarm monitoring station). 
						

							- 42 -
Emergency Evacuation
Establish and regularly practice a plan of escape in the event of fire. The following
steps are recommended by the National Fire Protection Association:
1. Position your detector or your interior and/or exterior
sounders so that they can be heard by all occupants.
2. Determine two means of escape from each room. One
path of escape should lead to the door that permits
normal exit from the building. The other should be
an alternative route, such as a window, should your
primary escape path be impassable. Station an
escape ladder at such windows if there is a long drop
to the ground.
3. Sketch a floor plan of the building. Show windows,
doors, stairs, and rooftops that can be used to escape.
Indicate escape routes for each room. Keep these
routes free from obstruction and post copies of the
escape routes in every room.
4. Assure that all bedroom doors are shut while you are
asleep. This will prevent deadly smoke from entering
while you escape.
5. To determine which escape path to use during a fire,
first feel the door. If it is hot, check your alternate
escape route. If the door is cool, open it cautiously. Be
prepared to slam the door if smoke or heat rushes in.
6. Where smoke is present, crawl on the floor; do not
walk upright. Smoke rises and may overcome you.
Clearer air is near the floor.
7. Escape quickly; dont panic.
8. Establish a common meeting place outdoors, away from your house, where
everyone can meet and then take steps to contact the authorities and account for
those missing. Choose someone to assure that nobody returns to the house —
many die going back.

FRONT

BACK

BATH
BEDROOMKITCHEN
BACK DOOR
1   FLOORST
BEDROOM
2    FLOORND
BATHBEDROOMPORCH
CLOSET
BEDROOMBEDROOM 
						

							- 43 -
Maintaining Your System
Taking Care of Your System
The components of your security system are designed to be as
maintenance-free as possible. However, to make sure that your
system is in reliable working condition:
1. Test your system weekly.
2. Test your system after any alarm occurs (see Testing the System
section).
Replacing Batteries in Wireless Sensors
Each wireless sensor in your system has a 9-volt or 3-volt battery. The
system detects a low battery in any wireless sensor, including smoke
detectors, the optional personal emergency transmitter, and the
optional portable wireless keypad. (The system detects a low battery
in a portable wireless keypad as soon as one of its keys is pressed, and
responds be displaying 
00 on the wired keypad.)
Alkaline batteries provide a minimum of 1 year of operation, and in
most units and applications, provide 2–4 years of service. Three-volt
lithium batteries provide up to 4 or more years of operation. Actual
battery life depends on the environment in which the sensor is used,
the number of signals that the transmitter in the sensor has to send,
and the specific type of sensor. Factors such as humidity, high or low
temperatures, or large swings in temperature may all lead to the
reduction of actual battery life in an installation.
If you have a low battery in a wireless sensor, the keypad displays a
LOW BATTERY message.
 In addition, a battery-operated smoke
detector with a low battery emits a single chirp sound
approximately once every 20–30 seconds, identifying itself as the
smoke detector with the weak battery.
NOTE: 
The 
LOW BATTERY message comes on as a warning that
battery replacement in the indicated sensor(s) is due within 30 days.
In the meantime, the sensor causing the low-battery indication is still
fully operational.Wireless
sensors may
not have
been
installed in
your security
system. 
						

							Maintaining Your System (cont’d)
- 44 -
Important:  Use only batteries recommended by your installer as
replacement.
Silencing Low Battery Warning Tones at the Keypad
You can silence the keypad’s warning tones by pressing the 
   1   key,
OFF
but the keypads 
LOW BATTERY message display will remain on as
a reminder that you have a low-battery condition in one or more of
your sensors. When you replace the weak battery with a fresh one, the
sensor will send a good battery signal to the control as soon as the
sensor is activated (opening/closing of door, window, etc.), causing the
LOW BATTERY display to turn off. If the sensor is not activated, the
display will automatically clear within approximately 1 hour.
Routine Care
Treat the components of your security 
system as you would any
other electrical equipment. Do not slam sensor-protected doors or
windows.
Keep dust from accumulating on the keypad and all protective
sensors, particularly on motion sensors and smoke detectors.
The keypad and sensors should be cleaned carefully with a dry soft
cloth. Do not spray water or any other fluid on the units. 
						

							- 45 -
Quick Guide to System Functions
FUNCTION PROCEDURE COMMENTS
Check Zones
Press
 [✴]Do this to view faulted zones when system is
not ready.
Arm System Enter code or press #
Press arming key desired
(AWAY, NIGHT-STAY*, STAY,
INSTANT, MAXIMUM)
* Press STAY twice in rapid
succession to arm NIGHT-STAYDo this to arm the system in the mode
selected.
Disarm System Enter code
Press OFF [1]Do this to disarm the system and silence
alarms.
Bypass Zones Enter code
Press [6]
Enter zone numbers to be bypassed
(use 2-digit entries)Do this to bypass protection zones.  Bypassed
zones are unprotected and will not cause an
alarm if violated.
Quick Bypass Enter code
Press [6] and stopDo this to bypass all faulted zones
automatically, if programmed.
Chime Mode ON Enter code
Press CHIME [9]Do this to turn on CHIME mode.  Keypad
will sound if doors or windows are violated
while system is disarmed.
Chime Mode OFF Enter code
Press CHIME [9]Do this to turn CHIME mode off.
Test Mode ON Enter code
Press  [5]Do this to enter TEST mode.  Sounds alarm
sounder and allows sensors to be tested.
Test Mode OFF Enter code
Press OFF [1]Do this to turn TEST mode off.  System returns
to normal mode.
Add or Change a
UserEnter Master code
Press  [8] key
Enter users 2-digit user no.
Enter code for that userDo this to add or change a user code.
Delete a User Enter Master code
Press  [8] key
Enter user number to be deletedDo this to delete a user code from the system.
Change a Master
CodeEnter Master code
Press [8] key
Press [0] + [2] (master user no.)
Enter new 4-digit Master code
Enter new Master code againDo this to change the existing Master code. 
						

							- 46 -
Summary of Audible Notification
(Alpha Display Keypads)
SOUND CAUSE DISPLAY
LOUD, INTERRUPTED*
Keypad & ExternalFIRE ALARM
FIRE is displayed; descriptor of zone in alarm is
displayed.
LOUD, CONTINUOUS*
Keypad & ExternalBURGLARY/AUDIBLE
EMERGENCY ALARMALARM  is displayed; descriptor of zone in alarm is
also displayed.
ONE SHORT BEEP
(not repeated)
Keypad onlya. SYSTEM DISARM
b. SYSTEM ARMING ATTEMPT
WITH AN OPEN ZONE
c. BYPASS VERIFYa.
SYSTEM READY is displayed.
b. The number and descriptor of the open protection
zone is displayed.
c. Numbers and descriptors of the bypassed
protection zones are displayed (one beep is
heard for each zone displayed). Subsequently,
the following is displayed: 
ZONE BYPASSED
SYSTEM READY.
ONE SHORT BEEP
(once every 40 seconds)
Keypad onlySYSTEM IS IN TEST MODE Opened zone identifications will appear.
ONE BEEP
(once every 40 seconds)
Keypad onlyLOW BATTERY AT A
TRANSMITTERLO BAT displayed with description of transmitter.
TWO SHORT BEEPS
Keypad onlyARM AWAY OR MAXIMUM
ARMED AWAY or
 ARMED MAXIMUM  displayed.
Red ARMED indicator lit.
THREE SHORT
BEEPS
Keypad onlya. ARM STAY, NIGHT-STAY, OR
INSTANT
b. ZONE OPENED WHILE
SYSTEM IS IN CHIME MODEa.
ARMED STAY or 
ARMED INSTANT displayed.
Red ARMED indicator lit.
b.
CHIME displayed, descriptor of open protection
zone displayed if the [✱
] key is pressed.
RAPID BEEPING
Keypad onlya. TROUBLE
b. MEMORY OF ALARMa.
CHECK displayed; descriptor of troubled
protection zone is displayed.
b.
FIRE or 
ALARM  is displayed; descriptor of zone
in alarm is displayed.
c. BELL FAILURE
d.
 SYSTEM LOW BATTERY
e.
 LAST 10 SECONDS OF EXIT
DELAYc.
BELL FAILURE or 
CHECK 70 is displayed.
d.
 SYSTEM LO BAT or 
BAT  is displayed.
e.
 ARMED AWAY or 
ARMED MAXIMUM is
displayed along with
 You may exit now.
SLOW BEEPING
Keypad onlya. EXIT DELAY WARNING (if
programmed)
b. ENTRY DELAY WARNINGa.
ARMED AWAY or
 ARMED MAXIMUM is
displayed along with 
You may exit now.
b.
DISARM SYSTEM OR ALARM WILL OCCUR is
displayed.
Exceeding the delay time without disarming
causes alarm
.
* If a bell is used as external sounder, fire alarm is pulsed ring; burglary/audible emergency is steady ring. 
						

							- 47 -
Glossary
The following terms are used throughout the manual.
ARM/DISARM:Armed simply means that the burglary portion of your system
is turned ON and is in a state of readiness. Disarmed means
that the burglary system is turned OFF, and must be re-armed
to become operational. However, even in a disarmed state,
emergency and fire portions of your system are still
operational.
KEYPAD:This is the area on your keypad containing numbered
pushbuttons similar to those on telephones or calculators. These
keys control the arming and disarming of the system, and
perform other functions described in this manual.
ZONE:
 A specific area of protection.
BYPASS:
 To disarm a specific area of burglary protection while leaving
other areas operational.
DELAY ZONE:
 An area of protection containing doors most frequently used to
enter or exit (typically, a front door, back door, or door from the
garage into the building). The delay zone allows sufficient time
for authorized entry or exit without causing an alarm. Consult
your installer for the entry and exit delay times that have been
set for your system during installation, and record them in the
space provided in “Entry/exit delays.”
DAY/NIGHT ZONE: An area of protection whose violation causes a trouble indication
during the disarmed (DAY) mode and an alarm during the
armed (NIGHT) mode. 
						

							- 48 -
UL NOTICE: This is a GRADE A system.
FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15 STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The
FCC requires the following statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly,
that is, in strict accordance with the manufacturers instructions, may cause interference to radio
and television reception. It has been type tested and found to comply with the limits for a Class B
computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed
to provide reasonable protection against such interference in a residential installation.  However,
there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
If using an indoor antenna, have a quality outdoor antenna installed.
Re-orient the receiving antenna until interference is reduced or eliminated.
Move the receiver away from the control/communicator.
Move the antenna leads away from any wire runs to the control/communicator.
Plug the control/communicator into a different outlet so that it and the receiver are on different
branch circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for
additional suggestions.
The user or installer may find the following booklet prepared by the Federal Communications
Commission helpful:  Interference Handbook.  This booklet is available from the U.S. Government
Printing Office, Washington, DC 20402.
The user shall not make any changes or modifications to the equipment unless authorized by the
Installation Instructions or Users Manual.  Unauthorized changes or modifications could void the
users authority to operate the equipment.
IN THE EVENT OF TELEPHONE OPERATIONAL PROBLEMS
In the event of telephone operational problems, disconnect the control by removing the plug from the
RJ31X (CA38A in Canada) telephone wall jack. We recommend that your certified installer
demonstrate disconnecting the phones on installation of the system. Do not disconnect the phone
connection inside the control/communicator. Doing so will result in the loss of your phone lines. If the
regular phone works correctly after the control/communicator
 has been disconnected from the phone
lines, the control/communicator has a problem and should be returned for repair. If, upon
disconnection of the control/communicator, there is still a problem on the line, notify the telephone
company that they have a problem and request prompt repair service. The user may not under any
circumstances (in or out of warranty) attempt any service or repairs to the system. It must be returned
to the factory or an authorized service agency for all repairs. 
						

							- 49 -
FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 68 NOTICE
This equipment complies with Part 68 of the FCC rules. On the front cover of this
equipment is a label that contains, among other information, the FCC registration number
and ringer equivalence number (REN) for this equipment. If requested, this information
must be provided to the telephone company.
This equipment uses the following jacks:
An RJ31X is used to connect this equipment to the telephone network.
The REN is used to determine the quantity of devices which may be connected to the
telephone line. Excessive RENs on the telephone line may result in the devices not ringing
in response to an incoming call. In most, but not all areas, the sum of the RENs should not
exceed five (5.0). To be certain of the number of devices that may be connected to the line,
as determined by the total RENs, contact the telephone company to determine the
maximum REN for the calling area.
If this equipment causes harm to the telephone network, the telephone company will notify
you in advance that temporary discontinuance of service may be required. If advance notice
is not practical, the telephone company will notify the customer as soon as possible. Also,
you will be advised of your right to file a complaint with the FCC if you believe necessary.
The telephone company may make changes in its facilities, equipment, operations, or
procedures that could affect the operation of the equipment. If this happens, the telephone
company will provide advance notice in order for you to make the necessary modifications
in order to maintain uninterrupted service.
If trouble is experienced with this equipment, please contact the manufacturer for repair
and warranty information. If the trouble is causing harm to the telephone network, the
telephone company may request you remove the equipment from the network until the
problem is resolved.
There are no user serviceable components in this product, and all necessary repairs must
be made by the manufacturer. Other repair methods may invalidate the FCC registration
on this product.
This equipment cannot be used on telephone company-provided coin service. Connection to
Party Line Service is subject to state tariffs.
This equipment is hearing-aid compatible.
When programming or making test calls to an emergency number, briefly explain to the
dispatcher the reason for the call. Perform such activities in the off-peak hours; such as
early morning or late evening. 
						

							- 50 -
WARNING!
THE LIMITATIONS OF THIS ALARM SYSTEM
While this system is an advanced design security system, it does not offer guaranteed protection
against burglary or fire or other emergency. Any alarm system, whether commercial or residential, is
subject to compromise or failure to warn for a variety of reasons. For example:
Intruders may gain access through unprotected openings or have the technical sophistication to
bypass an alarm sensor or disconnect an alarm warning device.
Intrusion detectors (e.g., passive infrared detectors), smoke detectors, and many other sensing
devices will not work without power. Battery-operated devices will not work without batteries,
with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will
not work if their AC power supply is cut off for any reason, however briefly.
Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the
alarm receiver. Even if the signal path has been recently checked during a weekly test, blockage
can occur if a metal object is moved into the path.
A user may not be able to reach a panic or emergency button quickly enough.
While smoke detectors have played a key role in reducing residential fire deaths in the United
States, they may not activate or provide early warning for a variety of reasons in as many as 35%
of all fires, according to data published by the Federal Emergency Management Agency. Some of
the reasons smoke detectors used in conjunction with this System may not work are as follows.
Smoke detectors may have been improperly installed and positioned. Smoke detectors may not
sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or
roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another
level of a residence or building. A second-floor detector, for example, may not sense a first-floor or
basement fire. Moreover, smoke detectors have sensing limitations. No smoke detector can sense
every kind of fire every time. In general, detectors may not always warn about fires caused by
carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper
storage of flammable materials, overloaded electrical circuits, children playing with matches, or
arson. Depending upon the nature of the fire and/or the locations of the smoke detectors, the
detector, even if it operates as anticipated, may not provide sufficient warning to allow all
occupants to escape in time to prevent injury or death.
Passive Infrared Motion Detectors can detect intrusion only within the designed ranges as
diagrammed in their installation manual. Passive Infrared Detectors do not provide volumetric
area protection. They do create multiple beams of protection, and intrusion can only be detected in
unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes
place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows.
Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or
any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense
changes in temperature; however, as the ambient temperature of protected area approaches the
temperature range of 90° to 105°F, the detection performance can decrease.