ADT Security Services Vista 10P User Manual

							 
– 31 – 


*
,	
+
 
3)



	




	0

The following lists the various command strings for adding user codes and attributes.  
Refer to the User Setup chart at the back of this manual for factory 
assignments of user attributes and to keep a record of user programming. 
 
 
Add User Code:  System Master code + [8] + user no. + 
new user’s code 
       User 01 = installer  User 03-16 = standard users
 
    User 02 = master  (factory set master code is 1234) 
  The Keypad beeps once to confirm that new user was added.  
Delete User Code:  System Master code + [8] + [user no.] + [#] [0] 
 The user code and all attributes programmed for this user number, 
including any associated RF keys, are erased from the system.  
 
Authority Level:  System Master code + [8] + [user no.] + [#] [1]+ auth. level 
Factory Assignments: Authority Levels (see definitions on previous page): 
users 03-16 = 0  0 = standard user   2 = guest 
 1 = arm only   3 = duress   
Access Group: System Master Code + [8] + [user no.] + [#] [2]+ group (1-8) 
Factory Assignments: none You can assign users to a group, then set an access schedule that 
defines the times this group of users can operate the system. The 
system ignores these users outside the scheduled times. 
 
RF User Number: System Master Code +  [8] + [user no.]  + [#] [4]+ zone no. 
Factory Assignments: none Use this command to assign a wireless button device (keyfob) to this 
user (keyfob must be enrolled in system first; see installer). 
 Zone number:  enter the zone number assigned to a button on the 
keyfob that will be used for arming/disarming by this user.
 
 
Pager On/Off:
 System Master Code +  [8] + [user no.]  + [#] [5] + 0 or 1 
Factory Assignments: You can program a user so that a message is sent to a pager  
users 01-16 = 1 (on)  whenever this code is used to arm or disarm the system. 
  Paging On/Off: 1 = allow paging; 0 = no paging for this user
  
						

							 
– 32 – 

$
 
0
	

The system provides one end-user schedule (programmable by master/installer only), 
which can control various types of events.  
• The schedule causes a defined event to start and stop (when appropriate) at a 
specified time.  
• The schedule can be set to automatically repeat at various intervals. 
• The schedule can be set for random starting, if desired.  
 
	


1.             +  [#] + [6] [4] 
 (Master Code) 
 
Alpha Displays: 
 (-7%61)(
6)%(= 83 %61  
 
2. Enter “01” as the 2-digit schedule number.  
 Press [
∗] to continue.
 )28)6 7,)( 23
=
59-8    
3. Enter the desired 2-digit event number from the 
following list.  
  00 = clear the scheduled event 
  01 = turn a programmed output on or off
 )28)6 ):)28
 
   (see 
Using Device Commands section for a list of output device numbers used 
in your system) 
  02 = set a user access schedule for one or more users 
(see 
Security Codes section for an explanation of access groups) 
  03 = send a “latch-key” report to a pager if the system is not disarmed by a specified 
time; message sent is “777-7777.” 
  04 = automatically arm the system in STAY mode at a specified time  
  05 = automatically arm the system in AWAY mode at a specified time  
  06 = automatically disarm the system at a specified time 
  07 = Display the word “REMINDER” at a specified time 
 Press [
∗] to continue.
  
4.  For event number “01,” enter the output number 
associated with this schedule. 
  Otherwise, this prompt is skipped. 
 Press [
∗] to continue to the “Start” prompt below.
 ():-) 291&)6

						

							 
– 33 – 

$

 
  
5.  For event number “02,” enter the access group 
number. Otherwise, this prompt is skipped. 
 Press [
∗] to continue to the “Start” prompt below.
 +6394 291&)6
<   
7.  Enter the event’s start time and days of week. 
  Hour = 00-12; minute = 00-59 
  AM = 0; PM = 1 
  Days = Position the cursor under the desired days 
using the [
∗] key to move forward, then press “1” to 
select the day. 
 Press [
∗] to continue.
 78%68 718;8*7
,,11%1 
  
8.  Enter the event’s stop time, AM/PM and days of 
week. 
  Refer to step 7 for available entries. 
 Press [
∗] to continue.
 7834 718;8*7
,,11%1 
  
9.  Enter the desired repeat option. 
  0 = no repeat 
  1 = repeat schedule weekly 
  2 = repeat schedule biweekly (every other week) 
  3 = repeat schedule every third week  
  4 = repeat schedule every fourth week 
  e.g., To make a schedule that happens everyday you 
would select all days with a repeat count of 1. To 
make a schedule that runs for one week then stops, 
select everyday with a repeat count of 0.
 6)4)%8 348-32
 <
  
10. Select the randomize option, if desired. 
  0 = no; 1 = yes 
  If selected, the schedule times will vary within 60 
minutes of the “hour” time. For example, if a 
schedule is set to start at 6:15pm, it will do so the 
first time 6:15pm arrives, but on subsequent days it 
will start anytime between 6:00 and 6:59 p.m.  
 Press [
∗] to continue.
 6%2(31->)
=
23 =
=)7 <
  
						

							 
– 34 – 
	,$$$(


 
0
1
2	

The system records various events in a history log, which can be viewed by the master 
user using an Alpha Display keypad. 
• The Event Log holds up to 32 events. 
• Events are displayed in chronological order, from most recent to oldest. 
• When the log is full, the oldest event is replaced by the logging of any new event. 
 
	)	

1
2

 
1.             + [#] +    6  +   0  
 (Master Code) 
 
Alpha Displays: 
(-7%61)(
6)%(= 83 %61
 
  
2.  The system displays the most recent event as follows: 
 • event number 
 • type of event, identified by its corresponding code 
(see your installer for the meaning of each code) 
 • zone or user number (depending on type of event) 
 • time and date of the event’s occurrence. 
3. Pressing [∗] displays previous events (back in time). 
  Pressing [#] displays events forward in time. 
4.  Exit the event log by pressing any key other than [∗] 
or [#].
 
 ) 9 4
%1 
 
 
  
						

							 
– 35 – 
	,$$$(



 
/0

1
2


The following table lists the codes that may appear when viewing the Event Log. 
If the event code is preceded by an “E” (as in the example display on the previous 
page), it means that the event is new and ongoing; if preceded by an “R,” it means the 
event has been restored. 
 
 
Code 
Definition 
110 Fire Alarm 
121 Duress 
122 Alarm, 24-hour Silent 
123 Alarm, 24-hour Audible  
131 Alarm, Perimeter 
132 Alarm, Interior 
134 Alarm, Entry/Exit 
135 Alarm, Day/Night 
143  Alarm, Expansion Module 
145 ECP Module cover tamper 
146 Silent Burglary 
150 Alarm, 24-Hour Auxiliary/Monitor 
zone 
162 Carbon Monoxide 
301 AC Power 
302  Low System Battery/Battery Test 
Fail 
305  System Reset (Log only) 
309  Battery Test Failure 
321 Bell/Siren Trouble 
333  Trouble, Expansion Mod. 
Supervision 
341  Trouble, ECP Cover Tamper 
344 RF Receiver Jam 
351  Telco Line Fault 
353  Long Range Radio Trouble 
373  Fire Loop Trouble 
374  Exit Error Alarm 
380  Global Trouble, Trouble 
Day/Night 
  
Code 
Definition 
381 RF Supervision Trouble 
382  Supervision Auxiliary Wire Zone 
383  RF Sensor Tamper 
384  RF Sensor Low-battery 
393 Clean Me 
401  Disarmed, Armed AWAY,  
Armed STAY 
403  Schedule Arm/Disarm AWAY 
406  Cancel by User 
407 Remote Arm/Disarm 
(Downloading) 
408  Quick Arm AWAY 
409  Keyswitch Arm/Disarm AWAY 
441 Disarmed/Armed 
STAY/INSTANT, 
Quick-Arm STAY/INSTANT 
442  Keyswitch Arm/Disarm STAY 
570 Bypass 
601  Manually Triggered Dialer Test 
602 Periodic Test  
606  AAV to Follow 
607 Walk Test Entered/Exited 
623  Event Log 80% Full 
625  Real-Time Clock was Changed 
(log only) 
627  Program Mode Entry (log only) 
628  Program Mode Exit (log only) 
750 -
789 Reserved for Configurable Zone 
Type report codes (check with 
central station when using these 
codes) 
 
  
						

							 
– 36 – 
$

-#
 
0
/
	




Using Test mode allows each protection point to be checked for proper operation.  
 
• The keypad sounds a single beep every 40 seconds as a reminder that the 
system is in the Test mode. 
 
•  Alarm messages are not sent to your Central Station while Test mode is on. 
 
1. 
 Disarm the system and close all protected windows, 
doors, etc. The READY indicator light should come 
on if all zones are intact (i.e., all protected windows, 
doors, etc. are closed.
 Alpha Displays: 
(-7%61)(
6)%(= 83 %61 
 
 
2.             +    
5   then  [0] (walk) 
 (Security Code) TEST 
 
The Dial test (option “1”) is intended for the installer 
and should not be used unless directed to do so by 
your Security System Representative.
 
=
(-%0 =
;%0/
 
  
3.  Listen. The external sounder should sound for 1 
second and then turn off. If the sounder does not 
sound, CALL FOR SERVICE.
 8)78 -2 463+6)77
 
 
 4. Fault zones. Open each protected door and window in turn and listen for three 
beeps from the keypad. Identification (zone number or zone description) of each 
faulted protection point should appear on the display. The display clears when the 
door or window is closed. 
5.  Walk in front of any interior motion detectors (if used) and listen for three beeps. 
The identification of the detector should appear on the display when it is activated. 
The display clears when no motion is detected.  
Note that if wireless motion detectors are used, there is a 3-minute delay between 
activations. This is to conserve battery life. 
6.  Test all smoke detectors, following the manufacturers instructions. The 
identification of each detector should appear on the display when each is activated. 
  If a problem is experienced with any protection point (no confirming sounds, no 
display), call for service immediately. 
  When all protection points have been checked and are intact (closed), there should 
be no zone identification numbers displayed on the keypad.
 
7.  Exit test mode:
     
                + [1]  
  (Security Code) 
If the test mode is inadvertently left active, it automatically turns off after 4 hours.
  
						

							 
– 37 – 


 
Check and  
Battery Displays 
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 * Not all systems 
use wireless 
sensors. 
The word 
CHECK on the keypads display, accompanied by a 
beeping at the keypad, indicates a trouble condition in the system.  
To silence the beeping for these conditions, press any key. 
1. 
A display of CHECK and one or more zone numbers 
indicates that a problem exists with the displayed zone(s) and 
requires your attention. Determine if the zone(s) displayed are 
intact and make them so if they are not. If the problem has been 
corrected, the display can be cleared if you enter the OFF 
sequence (security code plus OFF key) twice. If the display 
persists, CALL FOR SERVICE
. 
 
Note: A display of 
CHECK 70 on Alpha Display keypads 
indicates that the wiring connection to the external sounder is 
at fault (opened or shorted), and you should CALL FOR 
SERVICE. See “BELL FAILURE” on next page. A display of 
CHECK 90 indicates that RF interference may be impeding the 
operation of wireless sensors* in the system. See “
Rcvr Jam” 
on next page. 
2. 
If there are wireless sensors* in your system, the 
CHECK 
condition may also be caused by some change in the 
environment that prevents the wireless receiver from receiving 
messages from a particular sensor.  CALL FOR SERVICE if this 
occurs. 
  
IF YOU CANNOT CORRECT A CHECK DISPLAY, 
CALL FOR SERVICE. 
 
 
TYPICAL CHECK DISPLAYS  
06 
CHECK 
        AC  
 
 
 
FIXED-WORD DISPLAY KEYPAD 
  
	
	




ALPHA DISPLAY KEYPAD 
						

							 
– 38 – 


	

	


 
 
Words or letters in parentheses (   ) are those that are 
displayed on Alpha Display keypads. 
 
 
Other Trouble 
Displays 
  
* Any “beeping” that 
accompanies a trouble 
display can be stopped 
by depressing any key 
on the keypad or by 
entering an OFF 
sequence (code + OFF) 
  
 
 
 
 **    Not all systems use   
  wireless sensors. 
 COMM. FAILURE  Indicates that a failure has occurred in 
(or 
FC)  the telephone communication portion of 
your system.  
    CALL FOR SERVICE.  
 
SYSTEM 
LO BAT  Indicates that a low system battery  
(or 
BAT with no  condition exists.  Display is  
zone No.)  accompanied by beeping* at the 
keypad. If this condition persists for 
more than one day (with AC present), 
CALL FOR SERVICE. 
 
LO BAT  Indicates that there is a low battery 
+ zone descriptor  condition in the wireless transmitter** 
(or 
BAT with  number displayed (00 is RF keypad).  
zone No.)  Accompanied by a single beep*
 (about 
once every 40 seconds) at the keypad.  
    Either replace the battery yourself, or 
CALL FOR SERVICE.  If the battery is 
not replaced within 30 days, a 
CHECK 
display may occur.  
 
Rcvr Jam  Wireless part of the system is experiencing
(or 
CHECK 90)  RF interference which may impede 
reception from wireless sensors.** 
 
MODEM COMM  
(or 
CC)
 Indicates that the control is on-line with 
the Central Monitoring Stations remote 
computer.  
The control will not operate while on-line. 
Wait a few minutes — the display should 
disappear. 
 
BELL FAILURE Indicates that the wiring connection to  
(or 
CHECK 70)  the external sounder is at fault (open or 
shorted). Accompanied by “beeping” at 
the keypad. CALL FOR SERVICE.  
  
						

							 
– 39 – 


	

	


 
 
Other Trouble 
Displays 
(Continued) AC LOSS  The system is operating on battery power 
(or 
NO AC)
  only due to an AC power failure.  
  
If only some lights are out on the premises, 
    check circuit breakers and fuses and 
reset or replace as necessary.  
  If AC power cannot be restored and a 
“low system battery” message appears 
(see previous page), 
CALL FOR 
SERVICE. 
 
Busy-Standby 
(or 
dI)
 If this message remains displayed for more 
than 1 minute, system is disabled. 
CALL  
FOR SERVICE. 
 
OPEN CIRCUIT   The keypad is not receiving signals from  
(or 
OC)  the control. CALL FOR SERVICE. 
 
 
Long Rng Trbl If part of your system, back-up Long  
(or 
bF)  Range Radio communication has failed.  
   CALL FOR SERVICE.
 
 
 
TELCO FAULT    The telephone line has a problem. 
(or 
CHECK 94) CALL FOR SERVICE. 
 
 
Total Power Failure If there is no keypad display at all, and the READY indicator  
is not lit, operating power (from AC and back-up battery) for the  
system has stopped and the system is inoperative. 
CALL FOR 
SERVICE.  
 
In The Event Of Telephone Operational Problems 
In the event of telephone operational problems, disconnect the control from the phone line by 
removing the plug from the phone wall jack. We recommend that your installer demonstrate this 
disconnection on installation of the system. Do not attempt to disconnect the phone connection 
inside the control. Doing so will result in the loss of your phone lines. If the regular phones work 
correctly after the control
 has been disconnected from the phone wall jack, the control has a 
problem and you should immediately call for service. If upon disconnection of the control, there is 
still a problem on the phone line, notify the Telephone Company that they have a problem and 
request prompt phone repair service. The user may not under any circumstances attempt any 
service or repairs to the security system. Repairs must be made only by authorized service (see 
the LIMITED WARRANTY statement for information on how to obtain service).      
  
						

							 
– 40 – 
)$.


 
Taking Care of 
Your System The components of your security system are designed to be as 
maintenance-free as possible. However, to make sure that your system 
is in reliable working condition, do the following: 
1.  Test your system weekly
. 
 2.  Test your system after any alarm occurs.
  
Silencing Low 
Battery Warning 
Tones at the 
Keypad You can silence the keypad’s warning tones by pressing the OFF key, 
but the keypads low battery message display will remain on as a 
reminder that you have a low battery condition in one or more of your 
wireless sensors. When you replace the weak battery with a fresh one, 
the sensor sends a good battery signal to the control as soon as the 
sensor is activated (opening/closing of door, window, etc.), causing the 
low battery display to turn off. If the sensor is not activated, the display 
will automatically clear within approximately 1 hour. 
 
Replacing 
Batteries in 
Wireless Sensors 
 
 
Wireless sensors 
may not have 
been used in your  
security system   
IMPORTANT:  
Use only batteries 
recommended by 
your installer as 
replacement. 
Each wireless sensor in your system has a 9-volt or 3-volt battery. The 
system detects a low battery in wireless sensors, including smoke 
detectors, the personal emergency transmitter, and the portable 
wireless keypad and displays a low battery message*. (A low battery in 
a portable wireless keypad is detected as soon as one of its keys is 
pressed, and displayed as 00.). Battery-operated smoke detectors with 
a low battery also emit a single chirp sound approximately once 
every 20–30 seconds. 
Alkaline batteries provide a minimum of 1 year of operation, and in 
most units and applications, provide 2–4 years of service. 3-volt lithium 
batteries provide up to 4 or more years of operation. Actual battery life 
will depend on the environment in which the sensor is used, the 
number of signals that the transmitter in the sensor has had to send, 
and the specific type of sensor. Factors such as humidity, high or low 
temperatures or large swings in temperature, may all lead to the 
reduction of actual battery life in an installation. 
 
* The low battery message comes on as a warning that battery replacement 
in indicated sensor(s) is due within 30 days. In the meantime, a sensor 
causing a low battery indication is still fully operational.
  
Routine Care  Treat the components of your security system as you would any other 
electrical equipment. Do not slam sensor-protected doors or windows. 
 Keep dust from accumulating on the keypad and all protective 
sensors, particularly on motion sensors and smoke detectors. 
 The keypad and sensors should be cleaned carefully with a dry soft 
cloth. Do not spray water or any other fluid on the units.