ADT Security Services Vista 10P User Manual
Here you can view all the pages of manual ADT Security Services Vista 10P User Manual. The ADT Security Services manuals for Home Security are available online for free. You can easily download all the documents as PDF.
Page 41
– 41 – / / THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS General Your fire alarm system (if installed) is on 24 hours a day, for continuous protection. In the event of an emergency, the strategically located smoke and heat detectors will sound their alarms and automatically send signals to your system, triggering a loud, interrupted pulsed sound* from the Keypad(s) and any external sounders. A FIRE message will appear at your Keypad and remain on until you...
Page 42
– 42 – THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS Manually Initiating a Fire Alarm 1. Should you become aware of a fire emergency before your smoke or heat detectors sense the problem, go to your nearest keypad and manually initiate an alarm by pressing the panic key assigned for FIRE emergency for 2 seconds. If a key pair has been assigned for fire, press both keys at the same time. See the Using the Panic Keys section below for further details. 2....
Page 43
– 43 – THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National Fire Protection Associations National Fire Alarm Code (NFPA 72) noted below. Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of the...
Page 44
– 44 –
THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS
FRONT
BACK
BATH
BEDROOMKITCHEN
BACK DOOR
1 FLOORST
BEDROOM
2 FLOORND
BATHBEDROOMPORCH
CLOSET
BEDROOMBEDROOM
Establish and regularly practice a plan of escape in the
event of fire. The following steps are recommended by
the National Fire Protection Association:
1. Position your detector or your interior and/or
exterior sounders so that they can be heard by all
occupants....
Page 45
– 45 – 0 #1 FUNCTION PROCEDURE COMMENTS Check Zones Press READY key. View faulted zones when system not ready. Arm System Enter code. Press arming key desired: (AWAY, STAY, NIGHT-STAY, MAXIMUM, INSTANT) Arms system in mode selected. Quick Arm (if programmed) Press #. Press arming key desired: (AWAY, STAY, MAXIMUM, INSTANT) Arms system in mode selected, quickly and without use of a code. Bypass Zone(s) Enter code. Press BYPASS key. Enter zone...
Page 46
– 46 – 2 3 SOUND CAUSE DISPLAY LOUD, INTERRUPTED* Keypad & Ext. FIRE ALARM FIRE is displayed; zone number of zone in alarm is displayed. If a fire alarm is manually activated, zone number 95 will be displayed. LOUD, CONTINUOUS* Keypad & Ext. BURGLARY/AUDIBLE EMERGENCY ALARM ALARM is displayed. Zone number of zone in alarm is also displayed. ONE SHORT BEEP (not repeated) Keypad only a. SYSTEM DISARM b....
Page 47
– 47 – SOUND CAUSE DISPLAY LOUD, INTERRUPTED* Keypad & Ext. FIRE ALARM. FIRE is displayed; descriptor of zone in alarm is displayed. If a fire alarm is manually activated, zone number 95 will be displayed. LOUD, CONTINUOUS* Keypad & Ext. BURGLARY/AUDIBLE EMERGENCY ALARM. ALARM is displayed. If programmed, descriptor of zone in alarm is also displayed ONE SHORT BEEP (not repeated) Keypad only a. SYSTEM DISARM....
Page 48
– 48 – 4$ - $ NOTE: This is a “Grade A” Residential System RADIO FREQUENCY EMISSIONS Federal Communications Commission (FCC) Part 15 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Industry Canada This Class B digital apparatus complies with...
Page 49
– 49 –
.
5
SERVICING INFORMATION
Your local authorized service representative is the person best qualified to service your
alarm system. Arranging some kind of regular service program with him is advisable.
Your local service representative is:
Name:
Address:
Phone:
General Features
Features
Comments
Exit Delay
Entry Delay 1
Entry Delay 2
Night-Stay Zones
Zones:
Quick Arm
yes no
Quick Bypass
yes no
Automatic Paging...
Page 50
![Page 50
– 50 –
User Setup
The following chart will help keep track of system users. To program a user attribute:
Enter system master code + [8] + user no. + “#” command listed in column heading…
User
No. User
Name Security
Code
enter new code
Au th.
Level
[#] [1] + level
Access
Group
[#] [2] + group
RF Zone
Number
[#] [4] + zone no. Pager
on/off [#] [5] + 0/1
01 installer installer (0)
02 system master master (0)
03 (0) (0)
04...](http://img.usermanuals.tech/thumb/193/2824/w300_vista-10p-1478588761_d-49.png "Page 50
– 50 –
User Setup
The following chart will help keep track of system users. To program a user attribute:
Enter system master code + [8] + user no. + “#” command listed in column heading…
User
No. User
Name Security
Code
enter new code
Au th.
Level
[#] [1] + level
Access
Group
[#] [2] + group
RF Zone
Number
[#] [4] + zone no. Pager
on/off [#] [5] + 0/1
01 installer installer (0)
02 system master master (0)
03 (0) (0)
04...")
– 50 – User Setup The following chart will help keep track of system users. To program a user attribute: Enter system master code + [8] + user no. + “#” command listed in column heading… User No. User Name Security Code enter new code Au th. Level [#] [1] + level Access Group [#] [2] + group RF Zone Number [#] [4] + zone no. Pager on/off [#] [5] + 0/1 01 installer installer (0) 02 system master master (0) 03 (0) (0) 04...