ADT Security Services Simon XTi User Manual

Figure 2: Cross-zone diagram 
Motion sensor
Motion sensor
Path of pe rson walking
 
Home security 
The Simon XTi allows you to control whic h sensors are active at any given time. 
Table 5  below  describes the arming levels that  y
 ou can set from the control panel. 
Table 5: Arming levels 
Level Function Description 
1 Disarm  In this level, only 24-hour sensors are active. Environmental sensors 
(such as smoke or carbon monoxide detectors) stay active at all 
times. 
2  Arm door and window 
sensors...

Correct the problem as indicated or press Bypass. You will see the arming countdown 
message at the bottom of the screen. You  can press Cancel and enter your code to 
stop the arming process. 
Figure 3: Pre arm screen 
 
To disarm (level 1): 
1.  Press PRESS TO DISARM. 
2.  Enter your code when the keypad screen appears. 
 
The panel displays and speaks Disarmed and the panel beeps once. 
To arm doors and windows (level 2): 
1.  Ensure that all doors and windows are closed. 
2. Press 
. 
3.  Press DOORS...

 
To arm motion sensors (level 3): 
1. Press 
. 
2.  Press MOTION SENSORS ONLY (AWAY) (see  Figure 3 on page 8 ). 
3. 

If a code is required, enter your  code when the keypad screen appears. 
The panel speaks Motions On, starts an exit delay, and sounds exit beeps in 
groups of three until the exit delay expires. 
Note : Depending on your configuration, this option may not appear. 
To arm doors, windows, and motion sensors (level 4): 
1. Press 
. 
2.  Press ARM ALL (AWAY) (see  Figure 3 on page 8 ). 
3....

Note: Swinger shutdown does not affect Smoke, Fire, Carbon Monoxide and 
Environmental sensors. 
Ask your installer how this option is prog rammed and have them explain how it will 
affect your system operation. 
Exit/entry delay 
Your Simon XTi provides a delay after ente ring or exiting your home before the 
system is armed or disarmed.  Table 6 below  provides details for the entry and exit 
delay features. 
Table 6: Entry and exit delay details 
Function Description 
Entry delay  Some active sensors...

1.  Close all door and windows. 
2. Press 
. 
3.  Press the OFF next to Entry Delay (see Figure 3  on page 8 ). 
4. 

Press your desired arming leve l. The arming countdown begins. 
The screen displays 
(clock with a red strike through) with your arming level and 
speaks Doors and Windows On, No Entry Delay. 
Note:  To avoid causing an alarm, you must di sarm the system with a wireless keyfob 
before entering your home. 
Quick exit 
Use the quick exit feature wh en you want to briefly leave the house...

To bypass, or unbypass, a sensor: 
1. Press 
. 
2. Press SELECT 
. 
3.  Enter your master code. 
4.  Next to the sensor name, select 
 to bypass the selected sensor, or  to 
not bypass the selected sensor. 
Alarms 
The system provides a series  of alarms that indicate an unusual occurrence. When an 
alarm is active, the red alarm pop-up display shows with a message explaining what 
caused the alarm: 
 
To listen to and cancel an alarm:   
1.  If you would like to hear addition al alarm information, press...

There is a communicator delay (dialer delay) of 30 seconds programmed into the 
panel. The panel will delay 30 seconds before dialing the central monitoring station 
remote phone to send reports. You can have  your installer program this delay time 
between 15 and 45 seconds. To cancel an  accidental alarm before the programmed 
dialer delay time expires, press the red  alarm pop-up and enter your access code. 
The panel will speak  Alarm Cancel and sound beeps. 
Note : There is no dialer delay for fire...

Special chime 
The special chime feature allows you to install motion sensors in a patio or at the 
front door, and be notified when someone  is approaching those areas. These motion 
sensors are not used for intr usion protection. The panel w ill chime three times, if the 
special chime mode is enabled. 
Note:  If there are no special ch ime sensors in your system , the special chime option 
will not appear in the System menu. 
System status 
Press  and then press  next to Panel Status (no  code is...

Action Phone key presses  Comments 
Arm doors and windows 2  Press 2 again to activate the no 
delay feature 
Arm motion sensors  3   
Arm doors, windows, and 
motion sensors 2  3  
Listen in to house 
5 to listen in to the house 
Once in listen in to house the 
following options are available: 
•  0 or 1 to speak 
•  3 or 6 to listen 
•  7 to extend call
 
When in this mode, the user cannot 
re-enter the previous menu. You 
must hang up and call back in to 
the panel to perform additional 
functions....

Table 8: Key fob button operation 
Task Instructions 
Arm doors and windows. Press the Lock button once. 
Arm doors, windows, and motion sensors. Press the Lock button twice. 
Send a panic (intrusion, silent, or 
emergency) alarm to the central 
monitoring station.  Press the Lock and Unlock buttons simultaneously for 3 
seconds.  
(Check with your installer to find out how the key fob panic 
buttons will operate.) 
Disarm your security system. 
Press the Unlock button once.