ADT Security Services Safewatch Plus Entrepreneur User Manual

ADT-1090-INT  7/25/00  3:12 PM  Page 1 

ADT-1090-INT  7/25/00  3:12 PM  Page 2 

Table of Contents
*
System Reference.................................................2
Operating Your System.........................................3
ARMING.......................................................................................3
Arming The System Prior To Leaving.....................................3
Arming The System Without Leaving.....................................3
System Will Not Arm (Ready Light Off)..................................4...

Zone Identification Card
Space is provided for
recording the areas of
protection which are
;“““““““““‘““““““““’
: lndlvldual Zone Status
iReady statusIf lighted, zone is not secure.
i
;/flight& the system is ready to be armed.
Chedc doors, windows, etc.If not Iighted, one or more zones are faulted.i
!H not lighted, zone is secure.i,Indicator(s) of zonekl at fault will be lighted.
assigned to each zone.
i___~bll~~~~~_~~~~_~_bypassed. !. ,. ,
Depending upon the,I
installation, this card pulls1,\
out from...

Operating Your System
ARMING
Before the control can be armed, all of the intrusion zones must be secure asindicated by the green READY indicator. If the READY indicator is off, one or
more zones are faulted. The indicator(s) corresponding to the faulted zone(s) will
light. Use the pull out zone I.D. card on the control station to determine the areas of
protection which are assigned to each of the six (6) zones, thencheckthe appropriate
doors and windows to see that they are closed.
1.Verify that the...

;I Turning Off the lnterlor Zones and Entrance Delay
Control station key 4 may be used to turn the interior zones off prior to arming. This
will allow the system to alarm instantly if the entrance door is opened, while armed.
1.Press the 4 key and hold for three seconds.
2.When interior defined zones are turned off, the corresponding Zone indicators
will flash. The flashing will stop 30 seconds after the system is armed.
3.Arm the system by entering your User Code.Note: Upon disarming, the interior zones...

DISARMING
Your system is programmed with one or more entrance delay zones which allow
time to enter the premises without causing an alarm. Each delay door may be
programmed with a different entry time. Be sure to check with your installer.Note: If your system has the “Interior Follower” feature enabled, all
interior designated zones automatically become delay zones wheneveryou first enter through a delay zone. This allows you to walk In front of
motion detectors on the way to the control station after...

ALARM CONDITIONSWhenever an alarm occurs, the ALARM indicator will light, the audible alarm will
sound (if applicable), and the control 
wilI communicate with the central station (if
this option was purchased).
NOTE: If upon returning to the premises it 1s discovered that an alarm has
occurred, DO NOT ENTER THE PREMISES.Leave immediately and go to
the nearest phone and contact the appropriate authorities.
0 To reset the alarm:
1.
2.
Enter your User Code to reset the alarm.
The ALARM indicator will remain...

THE EMERGENCY KEYPAD PANIC ALARMSYour system may have been purchased with up to three emergency keypad panic
alarms. These may be used to activate an alarm in the event of a Fire, Hold-up, orother emergency condition, as programmed by your installer. Each alarm is
activated by pressing the appropriate emergency panic key (located below the
numeric keys).Each alarm may be audible or silent. It may also be programmed
to report 
the condition to a central monitoring station.Check with your security rep-...

SPECIAL FEATURES
The CHIME mode allows audible monitoring of zones while the system is
disarmed. When the CHIME mode is active, the control station sounder will beep
whenever a perimeter burglar defined zone (door, window, etc.) indicator is opened.
For example, the CHIME feature will cause the control station to beep two times
whenever the front door has been opened.Many businesses use this type of signal
to announce that a customer has entered.In a residential application, the CHIME
is useful for...