ADT Security Services RC8325ADT Wireless Indoor HD Camera Installation Guide

							Chapter 3 ADT Pulse Enrollment 
 
11. Assign the camera a unique name (usually based on the location of the 
camera) in the  Name field, and then click the  Save button at the upper right of 
the screen.  
 
12. The Cameras  screen appears, now displaying the added camera.  
 
13. At the top left of the screen, click  Go Back. 
14. You are returned to the Manage Devices  screen. The total number of installed 
cameras has increased by one. Click  Close. 
15.  Click Close  again to confirm.   
16. Disconnect the  camera  from the  Gateway and remove from powe r.  
17. Install the camera in  its final location.  For  Wall Mounting , refer to Chapter 4.  
RC8325-ADT Wireless Day/Night  HD Camera Installation Guide 11  
  
						

							Chapter 3 ADT Pulse Enrollment 
 
Using a Wireless Connection to  Enroll the Camera  
1. Set up  the camera, as described in  Chapter 2. 
2. Launch an Internet browser and log in to the Pulse portal or TS installer  app. 
3. Enter the Manage Devices  screen using one of these methods:  
•  For the Pulse portal, select the  System tab and click Manage Devices . 
•   For the TS installer app, click the  Pulse Devices link. 
The Manage Devices screen displays.  
4. In the  Manage Devices  screen, click Cameras . 
5.  Click the  Add Using WPS  button at the bottom of the screen .  
 
6.  Locate the  PIN number located on the label on the rear of the  camera. 
 
12   RC8325-ADT Wireless Day/Night  HD Camera Installation Guide  
  
						

							Chapter 3 ADT Pulse Enrollment 
 
7. On the  Add Camera  Using WPS screen, enter  the PIN  number  in the WPS PIN  
field .  
 
8.  Ensure that the  camera is powered on, and then click the  Continue button to 
initiate the WPS process .  
The following screen appears.  
 
RC8325-ADT Wireless Day/Night  HD Camera Installation Guide 13  
  
						

							Chapter 3 ADT Pulse Enrollment 
 
9. Press and hold the  WPS/RESET button on the  camera for 5 seconds to 
establish a wireless connection.   
Note:  You must complete the WPS connection 
within 2 minutes or else the proc ess will time out. 
The time remaining is displayed in the upper left 
portion of the screen.   
The Network/WPS LED flashes amber as the 
Gateway attempts to connect to the  camera.  
The wireless connection is successful when the 
Network/WPS LED turns solid gre en. 
 
 
14  RC8325-ADT Wireless Day/Night  HD Camera Installation Guide  
  
						

							Chapter 3 ADT Pulse Enrollment 
 
10.  When the  Camera Details  screen appears, showing that the  camera has 
been enrolled , assign the  RC8325-ADT a unique  name (usually based on the 
location of the  camera) in the Name field , and then click Save . 
 
The Pulse enrollment is complete. The newly -added device appears in the 
Cameras  list. 
 
11. At the top left of the screen, click  Go Back. 
12. You are returned to the Manage Devices  screen. The total number of installed 
cameras has increased by one. Click  Close. 
13.  Cl ick  Close  again to confirm.   
14. Disconnect the  camera  from power.  
15. Install the camera  in its final location . For Wall Mounting , refer to Chapter 4. 
RC8325-ADT Wireless Day/Night  HD Camera Installation Guide 15  
  
						

							Chapter 3 ADT Pulse Enrollment 
 
If the Camera Continually Goes Offline  
If after enrolling it the camera, it continually goes offline (Power LED blinks 
continually), the camera  will automatically attempt to recover the wireless 
connection. If the camera cannot recover on its own, take the following measures 
to re -establish the  Wi-Fi connection.  
1. Power cycle the camera.  
2. If the  previous  measure fails, move the Pulse Gateway closer to the camera.  
3. If the  previous  measure fails, press the camera’s reset button for 15 seconds, 
and then re -enroll the camera into Pulse.  
4. If the  previous  measure fails, install a Wi -Fi Range Extender model 
WN3000RPH -2ADPAS.  
 
16  RC8325-ADT Wireless Day/Night  HD Camera Installation Guide  
  
						

							Chapter 4 
Wall Mounting  
This section  provides details for  final mounting of  the RC8325- ADT 
Wireless Day/Night HD Camera. You should ensure that the camera  is 
configured and enrolled in ADT Pulse before permanently mounting it.  
1. Locate the mounting plate at the bottom of the camera stand and s lide the 
mounting plate  forward to release it from the  stand. 
2. Hold the mounting plate at  the location where you would like to  mount  the 
camera  and mark the location of the two mounting holes.  
3. Drill two pilot holes  on the mounting surface  at the marked locations. 
4. Align the two mounting holes  on the camera stand with the two  pilot holes, 
and mount the  mounting plate  to the surface using  the two screws  supplied. 
 
Figure  5: Installing the  Mounting Plate  
5. Slide the c amera stand  onto the mounting plate  until it clicks into place . 
 
Figure  6: Mounting  the Camera Stand  
4 
RC8325-ADT Wireless Day/Night  HD Camera Installation Guide  17 
  
						

							Chapter 4 Wall Mounting 
6.Remove the cable organizer from the stand. Insert the cables into the hole andrun cables through the organizer. Place the organizer back on the stand.
7.Connect the power cable  (and USB to RJ-45 Adapter Cable, if used) into the
back of the camera and plug the adapter end into a power outlet.
CAUTION:  Use only the power adapter provided. Using a different 
one can result in  hardware damage.  
F

igure  7: Routing the Cables  
8.Screw/attach the camera onto the camera stand.
F

igure  8: Attaching the Camera 
9.Adjust the camera  to a desired position and secure it firmly.
10.V erify that the camera is  active on the wireless network and is  recognized by
ADT Pulse
. Note:  If the camera does not re-c
onnect, use of the ADT Wi-Fi extender (part no. 
WN3000RPH-2 ADPAS) may be recommended to imp
rove wireless connectivity. 
USB to RJ-45 
Power Power 
18  RC8325-ADT Wireless Day/Night  HD Camera Installation Guide   
						

							Appendix A 
Specifications 
RC8325-ADT Wireless  Day/Night  HD Camera  
Model RC8325- ADT 
Dimensions 
W x H x D 2.56” x 2.56” x 1.34” ( 65mm x  65mm x 3 4mm ) 
Operating 
Temperature 32°F to 104 °F  ( 0°C to  40 C ) 
Video Compression H.264 and MJPEG  
Image Resolution 1280x 720, 640x480, 320x 240 (QVGA)  
Storage 
Temperature -4°F to 158 °F  ( -20 °C to 70 °C) 
Network Protocols  TCP/IP, UDP, ICMP, DHCP, NTP, DNS, SMTP, FTP, 
HTTP, HTTPS, DDNS, RTP, RTSP, RTCP, UPnP 
Network Interface 1 RJ-45 LAN connection for Ethernet through Micro 
USB to RJ-45 Adapter Cable 
Wireless Interface IEEE 802.11n/802.11b/802.11g compatible, WEP 
64/128 bit, WPA/WPA2 personal security support 
LEDs  2, Power and Network/WPS  
Power Adapter 12V/1A, 100 to  240 VAC 
A
RC8325-ADT Wireless Day/Night  HD Camera Installation Guide  19  
						

							Chapter 4 Wall Mounting 
 
Regulatory Approvals 
 
FCC Statement 
This equipment generates, uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful 
interference to radio  communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be determined by 
turning the equipment off and on, t he user is encouraged to try to correct the 
interference by one of the following measures:  
•   Reorient or relocate the receiving antenna.  
•   Increase the separation between the equipment and receiver.  
•   Connect the equipment into an outlet on a circuit different f rom that to which 
the receiver is connected.  
•   Consult the dealer or an experienced radio/TV technician for help.  
To assure continued compliance, any changes or modifications not expressly 
approved by the party responsible for compliance could void the user' s authority 
to operate this equipment. (Example  - use only shielded interface cables when 
connecting to computer or peripheral devices).  
FCC Radiation Exposure Statement 
This equipment complies with FCC RF radiation exposure limits set forth for an 
uncontrolled environment. This equipment should be installed and operated with 
a minimum distance of 20 centimeters between the radiator and your body.  
This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions :  
(1) This device may not cause harmful interference, and  
(2) T his device must accept any interference received, including interference that 
may cause undesired operation.  
This transmitter must not be co -located or operating in conjunction with any other  
antenna or transmitter.  
20  RC8325-ADT Wireless Day/Night  HD Camera Installation Guide